Filter Results By:
Products
Applications
Manufacturers
- Omnicor
product
Network Testing Tools
Network IP traffic packet generators are used for network performance testing under maximum or partial throughput conditions. Network health can be analyzed by network traffic measurement in a testbed network, using an IP network traffic generator such as IP Traffic Test and Measure. The traffic generator sends packets, often with a unique packet identifier, making it possible to keep track of the packet delivery in the network.Network impairment simulation (emulation) is a technique for testing the performance of real applications over a virtual network. The aim is to assess performance, predict the impact of change, analyze impairment conditions or otherwise optimize technology decision-making. Measurements usually focus on simulation of conditions like delay, jitter, latency, dropped packets and limited bandwidth.
-
product
Visible Fault Identifier
TVFI
The Yamasaki TVFI Visible Fault Identifier is a practical palm sized solution for finding breaks, bends and faulty connectors or splices in fiber optic cable.
-
product
Cable Identifier
OFI-50A
OFI–50A uses optical fiber sensing principle to confirm the target fiber; It can quickly identify deep buried, overhead and pipe fiber cable without any destroy, and provide a simple method for maintenance personnel. Users only need gently knock on cable, when knocking to the target cable, OFI-50 can clearly hear the knock from earphone, which can accurately identify the target cable.
-
product
CANbus Controller for VMEbus
VME360
The VME360 CANbus controler is a 6U VMEbus board based on four SJA1000 CANbus controllers. Each SJA1000 provides an interface to the popular CANbus that supports both standard (11-bit) and extended (29-bit) identifier fields. Front panel LEDs provide diagnostical network information. The VME360 provides four CANbus interfaces. The CAN network is a serial communication protocol which efficiently supports distributed control with a high level of reliability.
-
product
Refrigerant
The Mentor Automotive Refrigerant Identifier portfolio provides simple and accurate refrigerant analysis. The Mentor is a user-friendly, cost effective R-1234yf and R-134a refrigerant purity analyzer designed with state-of-the-art non-dispersive infrared (NDIR) technology for the identification of refrigerant gases in automotive air-conditioning systems.
-
product
CANbus Controller Standard Interface
PCI360
The PCI360 CANbus controller PCI card is based on the SJA1000. The SJA1000 provides an interface to the popular CANbus that support both standard (11-bit) and extended (29-bit) identifier messages. LEDs provide diagnostics information.The CAN network is a serial communication protocol which efficiency supports distributed real-time control with a high level of reliability.
-
product
FibreSeek | PON Power Meter
TP40
Testing in the FTTx environment just got easier with Yamasaki’s latest piece of PON Test Equipment, the TP40 FiberSeek FTTx PON Power Meter. The TP40 includes FTTH PON Testing, 6 Wavelength Optical Power Meter & Visible Fault Identifier all in one unit. This rugged hand held unit includes a removable rubberized boot; bright backlit LCD; auto shut off function; wide measurement range; upstream burst mode; accurate testing and bright flashing VFI.
-
product
LanCaster
4402700
Indicates all common wiring faults including split pairs Shows which end the installed link contains the fault Cable Length Meter, Tone Generator & Service Indicator Instant digital display gives unambiguous fault indication Rugged Palm-Top design weighs less than 350g (12oz) Complete with 1 Active Remote unit and test leads Up to 16 unique Active Remote units / Office Identifiers
-
product
HDTV / SDTV FORMAT IDENTIFIER
TFI-7
Description: The TFI-7 is a hand-held meter used to identify the picture format of any HDTV, EDTV, SDTV, and HD-TVI video signal.
-
product
Handheld Optical Fiber Identifier
JW3306D
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
JW3306D Optical Fiber Identifier is an important tool for optical maintenance, which is used for nondestructive fiber identification project. Meanwhile it also has Visual Fault Locator module with fault location function. Useing the macro bending technology on line for nondestructive testing, JW3306D can measure the signal direction and power and avoid misoperation resulting in interrupted lines.
-
product
SMD Tweezer Capacitance Resistance Diode Tweezers Test Pen Multimeter SMD Meter
VA50372
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
SMD tweezer Capacitance Resistance Diode Tweezers Test Pen Multimeter SMD Meter VA503 SMD Components Identifier
-
product
Multibeam Profiling Software
MB-DataLogger
Teledyne BlueView's MB-DataLogger software provides a powerful tool for multibeam profiling applications. From mission setup to data playback, review, and export, MB-DataLogger gives users full end-to-end mission support. Set up data collection parameters (sonar head range, ping rate, filename identifiers, etc.) for a SmartCore-enabled system prior to deployment, then review bathymetric profiles in a 2D or 3D waterfall display with or without navigation correction post mission. When regions of interest are identified, export batches of data files to georeferenced point clouds to be imported by third-party applications. MB-DataLogger is the software Swiss army knife for your BlueView multibeam profiling system.
-
product
Cable Identifier
K&S Engineering and Scientific Ltd
K&S Engineering and Scientific LTD's Cable Identifier Set offers the user a compact, portable solution for cable identification. Depending on the user preference, the Cable Function Generator and Cable Identifier Unit can be jointly housed in a rugged briefcase, or alternatively, for the user requiring a more rugged unit, can be delivered as two individual units each with their own carry-case. With the Cable Identifier Set, power optimum levels are selected by means of a rotary switch and the power levels are displayed on a meter located on the Cable Function Generator. As the Cable Identifier Unit is capable of detecting magnetic fields around mains cables it has the added advantage of the user being able to use this as a stand-alone unit to detect power cable configuration.
-
product
Live Fiber Identifier
TM-OFI-401L
TM-OFI-401L Optical Fiber Identifier Suitable for 0.25mm, 0.9mm, 3.0mm fiber, and no need to replace the clamp block, more convenient than others;
-
product
Fiber Identifier & VFL
Are designed to non-invasively identify continuous-wave signals in fiber optic cables. They are low cost, hand-held tools.
-
product
Circuit Breaker Identifiers
190 CBI
Standard Electric Works Co., Ltd
● 190 CBI is an easy tool to find the circuit breaker or fuse supplying electrical power to an outlet or lighting fixture. Just plug the transmitter into the outlet.● Use the receiver to scan the circuit breaker panel box. An audible tone will be clearly heard when the right circuit breaker is scanned.● The plug of transmitter is changeable. The plug of transmitter could be changed for customers' requirement from different countries.
-
product
Circuit Breaker Identifiers
191 CBI
Standard Electric Works Co., Ltd
● 191 CBI is an easy tool to find the circuit breaker or fuse supplying electrical power to an outlet or lighting fixture. Just plug the transmitter into the outlet.● Use the receiver to scan the circuit breaker panel box. An audible tone will be clearly heard when the right circuit breaker is scanned.● The plug of transmitter is changeable. The plug of transmitter could be changed for customers' requirement from different countries.
-
product
FiberScout | Fault Identifier & Singlemode Fibre Length Tester
TS21
The TS21 Fiber Scout was designed and developed by Yamasaki as a cost effective and simple solution for identifying faults and testing the length of singlemode fibers. This lightweight, rugged, dustproof and water resistant piece of test equipment can list up to 8 results at one time and has three brilliant functions.
-
product
Optical Fiber Identifier
X5004
Lower power indicationEasy-to-replace adaptersEasy-to-use with "ONE KEY" operationDisplays the relative core powerDurable metal housing and quality constructionEfficiently identifies the fiber transmission direction and frequency tone (270Hz, 1 KHz, 2 KHz) with audible warning
-
product
Mineral Identifier
TerraSpec Halo
Analytical Spectral Devices, Inc.
For exploration and mine geologists, the PANalytical ASD TerraSpec Halo mineral identifier is the next generation all-in-one mineral analysis system that allows you to immediately identify alteration minerals with a simple pull of a trigger for faster delineation of alteration, speedier core logging and quick confirmation of ore mineralogy.
-
product
Cable ID & PoE Tester
PK-170 INNOTESTER PRO
INNOTESTER PRO combines the functions of a smart cable tester, network tester, port identifier and organizer with the capability to identify up to 100 cables run at a time, and 8 Test + ID remotes allows one person to test 8 cables run up to 600 meters. Tone mode, transmits 2 powerful tones for tracing inactive and active network cables on a Switch or HUB. More effectively tracing at patch panel, termination blocks or hidden within bundles.
-
-
product
Thickness Gauges
CMX DL
The CMX DL has all the features of the CMX, plus a huge storage capacity, using multiple file structures. Select between to file formats: Sequential, with auto identifiers or, our standard alpha numeric grid format.
-
product
Optical Fiber Identifier
OrienTek Optical Technology Ltd.
Optocal Fiber Identifier Economical Solution for Integrated Fiber Preparation Tool Demand● 4 easy-change chucks for:bare fiber, patch cords & ribbon fiber● Identifies 3 common test tones● Identifies dominant traffic direction, audible alarm● Approximate core power reading● Low false detection & insertion loss● Very easy to operate● Battery low indication
-
product
Color Identifier
CAPSURE
Stores up to 100 color capturesToggles easily across multiple PANTONE LibrariesSynchronizes with popular design applications, including Adobe Photoshop, Adobe Illustrator and QuarkXPressAutomatically updates color libraries through CAPSURE SyncCompact and lightweight weighs just six ounces (with battery)Annotates colors with a voice recording and time-and-date stampLarge 1.75 inch-color viewing screen
-
product
Fiber Identifier
OFI-20A
OFI-20A can detect optical signal presence, type and direction anywhere on fibers during optical network deployment, maintenance and troubleshooting. With non-destructive macro-bend detection technology, it introduces no damage to tested fiber or interference to the service on fiber. OFI-20A is able to identify wide-spectrum signals (such as signals in CATV system) and can be used in SONET/SDH & DWDM systems tests.
-
product
F Set / Cable Pair Identifier
CZ1000
The CZ1000 Cable Pair Identifier (F-Set) is the original and best cable tracer and pair identifier used by electricians, telecommunications, and data cabling companies Australia wide. Designed for finding conductors in multi pair cabling applications, particularly in copper telecommunication cables, it soon became the standard tone and probe for telecommunications. Once electricians realised how good it was as a cable tracing tool it soon became the standard cable tracing tool for the electrical industry. Electricians, technicians, engineers, and tradespeople all rely on the CZ1000 to get their daily jobs done.
-
product
Optical Fiber Identifiers
Optical fiber identifiers from GAOTek are ruggedly built and easy to use. Using this instrument, detect the presence of signals on optical fibers. For field technicians, fiber identifiers are an important tool. Instantly verify whether live fibers are connected or disconnected, and trace fibers from end to end.
-
product
CANbus Controller
CPCI360
The CPCI360 CANbus controller is a 3U CompactPCI card based on the SJA1000. The SJA1000 provides an interface to the popular CANbus that supports both standard (11-bit) and extended (29-bit) identifier messages. Front LEDs provide diagnostic information.
-
product
INNOTESTER
PK-160/160PL
INNOTESTER (PK-160/160PL) combines the function of a smart cable tester, network tester, port identifier and organizes with the capability to identify up to 100 cables run at a time, and 8 Test + ID remotes allows one person to test 8 cables runs up to 600 meters.
