Modules
See Also: Contacts, Boards, ITA, Cable Assembly, Cards
-
Product
Intelligent 16 Bit Data Acquisition
CPCI-AD16
Data Acquisition Module
The CPCI-AD16 module provides a 3U high performance data acquisition subsystem. The Local DSP can be used to simply move data samples to the CPCI bus or can provide processing functions such as limit checking, FFT’s, digitalfiltering, etc. Application software can be downloaded to the DSP via the CPCI interface. Instrumentation amplifiers provide over-voltage protection, gain and filtering on a per channel basis. Internal scan and trigger clocks are derived from either the CPCI bus clock or the local DSP clock. Dual 32 bit timers can programmed to pace the acquisition process. The CPCI-AD16 can also accept external scan and trigger signals from a front panel connector.
-
Product
PXI Very High Density Multiplexer, 198-Channel, 1-Pole
40-675B-002-198/1
Multiplexer Module
The 40-675B-002-198/1 (PXI) and the 42-675B-002-198/1 (PXIe) are 198-channel, 1-pole multiplexers and are part of our range of very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems.
-
Product
NI-9219, 100 S/s/channel, 4-Channel C Series Universal Analog Input Module
779781-02
Analog Input Module
100 S/s/channel, 4-Channel C Series Universal Analog Input Module - The NI‑9219 is designed for multipurpose testing. With the NI‑9219, you can measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors, as well as make quarter-bridge, half-bridge, and full-bridge current measurements, with built-in voltage and current excitation. Each channel is individually selectable, so you can perform a different measurement type on each channel.
-
Product
Radio Module (2x2)
SX-PCEAN2
-
This SX-PCEAN2 is a dual band PCI Express wireless module, featuring two stream MIMO technology and industrial temperature support with throughput up to 300 Mbps. It is an ideal solution for high performance applications based on the NXP i.MX6 platform.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-151-HI
-
The 40-230-151-HI (PXI) and 42-230-151-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4.5Ω and 2.95MΩ with 0.25Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI Single 2x2 RF Matrix 2.5GHz 50 SMB
40-877-001
Matrix Switch Module
The 40-877-001 is a 50Ω 2x2 RF matrix with 1 bank in a single PXI slot. Loop-thru connections are provided on both the X and Y axis allowing the attachment of terminations for unused signals or for expansion to other matrices. Larger matrices are easily built with varied X and Y dimensions, such as 8x2 and 4x4 using multiple 40-877 modules. The module has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
Product
sbRIO-9225, Non-Enclosed, 300 Vrms, 50 kS/s/ch, 24-Bit, Simultaneous Input, 3-Channel C Series Voltage Input Module
780588-01
Voltage Input Module
Non-Enclosed, 300 Vrms, 50 kS/s/ch, 24-Bit, Simultaneous Input, 3-Channel C Series Voltage Input Module - The sbRIO‑9225 performs differential analog input. The wide measurement range is well suited for high-voltage measurement applications such as power metering, power quality monitoring, motor test, battery stack testing, and fuel cell tests. You can perform transient and harmonic analysis with high-speed simultaneous sampling. In addition, you can prevent ground loops and add safety to a system with 600 Vrms channel‑to‑channel isolation between the three sbRIO‑9225 channels. Non-enclosed modules are designed for OEM applications.
-
Product
Isolated Thermocouple Input Module
ADAM-3011
-
1000 VDC, fully isolatedConfigurable thermocouple typeFlexible DIN-rail mountingLinearized thermocouple measurementOperates from a single +24VDCTemperature range of 0 to 50°C
-
Product
DDR4 X16 2-wing BGA Interposer For Logic Analyzers, Connects To 61-pin ZIF
W4641A
Interposer
The W4641A DDR4 2-wing BGA interposer for DDR4 x16 BGA DRAM probing takes full advantage of the quad sample state mode on the U4164A the W4641A is the smallest BGA interposers for DDR4 x16 DRAM capable of capturing simultaneous read and write traffic at data rates exceeding 3.2 Gb/s. U4208A and U4209A probe/cables connect any W4640A Series DDR4 BGA interposer directly into the U4164A logic analyzer module from 61-pin high density zero insertion force (ZIF) connectors that attach to the W4640A Series BGA interposer wings.
-
Product
PXIe-2529, 128-Crosspoint, 4x32 OR 8x16, 2-Wire PXI Matrix Switch Module
780587-29
Matrix Switch Module
128-Crosspoint, 2-Wire PXI Matrix Switch Module—The PXIe‑2529 is a high‐density PXI matrix switch module that you can configure as either a 4x32 or an 8x16 2‑wire matrix by using different terminal block accessories. It uses electromechanical relays that offer excellent performance for high-power signals and low thermal offset for accurate measurements at low-voltage levels. The PXIe‑2529 also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
Product
(70×90×12mm) Single Channel Gain Block MSA Compact Pre-Amplifier EDFA Module
SPA4300-GM02
-
Hangzhou Huatai Optic Tech. Co., Ltd.
SPA4300-GM02 is a gain block optical Pre-amplifier EDFA module, adopts 70×90×12mm MSA compact package. It is featured with high reliability, superior optical performance and compact reasonable configuration by Industrial standard, creating the most flexible and variable low-cost amplifier in the market. This module is suitable for multiple network application, especially the application that requires 40GB/S transmission speed.
-
Product
68-Pin SCSI Micro-D Female Straight PCB
40-963-068-SF
-
Ideal for user created termination schemes where the termination is to be on the front of the product or remotely connected to the module by cable. Suitable cables for this product are contained elsewhere in the data sheet. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
PXIe-5663E, 6.6 GHz PXI Vector Signal Analyzer
781339-03
Signal Module
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5663E provides a low-cost solution to high-performance RF measurements.The PXIe-5663E comprises the following modules:• PXIe-5601 RF Signal Downconverter• PXIe-5622 IF Digitizer• PXIe-5652 RF Analog Signal GeneratorThere is no physical device named "PXIe-5663E".
-
Product
PXI Dual Microwave Transfer Switch 18GHz 50 SMA
40-782A-522
Switch Module
The 40-782A-522 is a dual transfer switch and is part of our range of PXI microwave switching modules. It has a characteristic impedance of 50Ω and a maximum operating frequency of 18GHz. Connections are made via front panel mounted high quality SMA coaxial connectors.
-
Product
Voltage Meter
MDS32
-
M-module MDS32 is a mezzanine module designed to analyze the state of discrete sensors. М-module MDS32 is installed on the mezzanine carrier - module НМ-М and connected to it via a local information highway. Up to four m-modules of various types can be installed on the NM-M module. The NM-M module together with the m-modules installed on it forms a C-1 VXI module for 64 analyzing channels and is used to create information measuring VXI systems.
-
Product
PXI Thermocouple Simulators
-
Our PXI Millivolt Thermocouple Simulator modules provide 32, 24, 16 or 8 channels of accurate low sources. They are ideal for the simulation of thermocouples and can be used for sensor emulation in ECU testing. The channels can be operated with one of three voltage ranges covering most thermocouple types. We can also supply connection solutions allowing the easy integration of the Thermocouple Simulator into your test system.
-
Product
ccXMC-Serial
-
Conduction Cooled XMC module with 16 differential IO and 12 RS-232 IO plus Spartan VI 100 FPGA. Industrial Temp. SOSA pinout. Initial design has 2 HDLC, 2 NRZ, and 3 UART ports implemented.
-
Product
PXI Single RF Attenuator 63dB in 1dB steps
41-180-021
Attenuator
The 41-180 Programmable Attenuator Module is available with either one or two independently programmable attenuators in a single width 3U PXI module
-
Product
PXI Dual 8 to 1 Mux 1GHz 75Ohm 1.0/2.3 Con
40-748-731
Multiplexer Module
The 40-748 is a dual 8 to 1 RF MUX available in 50 Ohm or 75 Ohm versions occupying a single PXI slot. The module is available with SMB or SMA connectors for 50 Ohm versions or, 1.0/2.3 or Mini SMB connectors for 75 Ohm versions. Applications for the 40-748 include routing high frequency signals to and from oscilloscopes, analyzers, signal generators and synthesizers, telecoms tributary switching, video/audio switching and switching high frequency logic signals.
-
Product
Embedded BACnet Stack For 32 Bit Processors
FreeRange VSB
-
PolarSoft FreeRange is a set of modular software component modules that provide BACnet client and server application layer, network layer and media access (MAC) layer communications services to embedded systems programs. FreeRange is written entirely in the C language for ease of portability to various platforms.
-
Product
75 Ohm Mini SMB Cable Assembly
40-977-751-2m
RF Cable Assembly
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
Network Interface Controllers for Anonymous Subscriber Messaging (FC-ASM)
Fibre Channel
-
Avionics Interface Technologies
FC-ASM Network Interface Controllers for Avionics applications. The AIT FC-ASM NIC solutions are Quad interface modules providing 4 independent NIC interfaces on a single module. All FC-ASM and Fibre Channel protocol operations are handled onboard, providing an efficient, high bandwidth, FC-ASM protocol offload solution for 1Gbp/s and 2Gbp/s FC-ASM.
-
Product
PXIe Semi-Dynamic Digital I/O Module, 32-Channel
42-419-003
Digital I/O
The 40-419-003 (PXI) and 42-419-003 (PXIe) are a 32-channel digital I/O modules suitable for operating external devices, such as power, RF and high voltage relays, solenoids and lamps. They can also be used for interfacing with external logic such as a programmable instrument with a BCD interface depending upon the module’s driving capabilities.
-
Product
cRIO-PB-MS, Master/Slave, C Series PROFIBUS Interface Module
781352-01
Interface Module
Master/Slave, C Series PROFIBUS Interface Module - The cRIO-PB-MS connects NI programmable automation controllers (PACs) to PROFIBUS industrial networks as powerful masters or slaves. The interface includes the NI‑PROFIBUS for CompactRIO instrument driver for human machine … interface (HMI) and SCADA applications, as well as a graphical networking Configurator software. You can perform PROFIBUS device automated test using these interfaces. The cRIO-PB-MS is compatible with only CompactRIO systems.
-
Product
8-Channel A/D & D/A Zynq UltraScale+ RFSoC Gen 3 Processor - QuartzXM
Model 6003
-
- Unique QuartzXM eXpress Module enables deployment in custom form factors- Supports Xilinx Zynq UltraScale+ RFSoC FPGAs- 16 GB of DDR4 SDRAM- Measuring only 2.5 by 4 inches- LVDS connections to the Zynq UltraScale+ FPGA for custom I/O- GTY connections for gigabit serial communication- Ruggedized and conduction-cooled versions available- Includes a complete suite of IP functions and example applications- Model 8257 1-Slot 3U VPX Development Chassis for Quartz Products
-
Product
AMR Module Warm-up Station
3206G
-
The Model 3206G Meter Warm-Up Station for AMR Modules has been specifically designed for meters that utilize the DCSI TWACS™ power line carrier communications module. Additionally, this versatile unit includes voltage output and voltage input connections that allow you to test additional brands of power line carrier modules when using the manufacturer’s supplied module. The Model 3206G can even be used as a simple meter warm-up station.
-
Product
PXI/PXIe Microwave Relay, Single SPDT, 12.4 GHz, 50 Ω, N-Type, Remote Mount, Failsafe
42-780B-511-E
Relay
The 40-780B-511-E (PXI) and 42-780B-511-E (PXIe) are single failsafe SPDT 12.4 GHz unterminated microwave relay modules with remotely mounted relays. The 40/42-780B range is available with one, two, three or four SPDT front panel mounted relays capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions can support up to three SPDT relays in a single slot.
-
Product
Analog I/O Module with 16 single-ended analog output channels
IO111
-
This I/O module is a dedicated analog output module with a resolution of 16 bits. Each of the 16 output channel has its dedicated D/A converter with an update time of 3µs. The output coupling of the module is single-ended for all channels. The output range of each channel can be selected individually.
-
Product
USB DAQ
-
ADLINK USB DAQ modules leverage the expertise of ADLINK's analog design capability, enhancing convenience of data acquisition. Simply plug the ADLINK USB DAQ into a USB port on your computer or notebook for performance equaling or even exceeding that of ADLINK PCI/PCIe DAQ cards, with no need to power down or open the chassis. As well as providing basic voltage measurement, ADLINK USB DAQ modules feature built-in signal conditioning to directly receive measurement from most commonly used sensors, with no need for extra signal processing. From basic testing to high-accuracy measurement, from portable application to industrial automation, the ADLINK USB DAQ series delivers easy, efficient, and accurate measurement every time.
-
Product
4-Ch 500 MHz A/D with DDC & 4-Ch 800 MHz D/A with DUC, Virtex-6 FPGA - 6U VPX
Model 58651
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 500 MHz 12-bit A/Ds- Four multiband DDCs (digital downconverters)- Two DUCs (digital upconverters)- Four 800 MHz 16-bit D/As- Two multiboard programmable beamformers- Up to 4 GB of DDR3 SDRAM; or: 64 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
