Modules
See Also: Contacts, Boards, ITA, Cable Assembly, Cards
-
Product
PXI 4 Slot BRIC 264x4 1-Pole (6 sub-cards)
40-562A-021-264X4
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 16 Amp Power Multiplexer, Quad 4-Channel 1-Pole (SP4T)
40-662A-001
Multiplexer Module
The 40-662A-001 is a quad 4-channel, 1-pole (SP4T) MUX and is part of our range of 16 Amp PXI power multiplexer modules is available in seven configurations ranging from 4-off 2:1 multiplexers to 1-off 16:1 multiplexer.
-
Product
8-Ch RTD Input IDAQ Module
iDAQ-815
-
Hot-swappable in iDAQ system8-ch simultaneous RTD sampling24-bit resolutionMultiple supported RTD types and connection typesIsolation protection up to 600VRMS
-
Product
PXI 4-Slot BRIC Matrix, 176x4 1-Pole (4 sub-cards)
40-562B-021-176X4
Matrix Switch Module
The 40-562B-021-176X4 is a high density BRIC4 matrix module with a size of 176x4 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
Load Modules
-
Load Modules are available with a selection of voltage and current ranges. Use for discharge testing batteries, power supplies or test gear.
-
Product
External Input Module
EIM-01
-
The EIM-01 external input module is used to safely isolate and input an external drive signal into the MAC-01, -02 or -03 AC Power Sources/Frequency Converters. The unit can accept various waveforms from laboratory or programmable oscillators or from a Titan MOS-01, -01A, -01B when used as a slave unit in multi-KVA systems. BNC input is completely isolated and floating with 1,500VAC breakdown and excellent common mode rejection. A recessed 8% gain adjustment control is also provided. The EIM-01 must be factory installed.
-
Product
Multi-standard Cable/terrestrial Modulator For PCIe
DTA-2111
-
DekTec's PCIe modulator for most QAM-, OFDM- and VSB-based modulation standards. The DTA-2111 has a programmable output level with excellent signal quality due to digital upconversion.
-
Product
4-CH Analog Output Module
ND-6024
Analog Output Module
- Channels: 4- Voltage Output: -10 V to 10 V- Output Isolation: 5000 VRMS- Resolution: 12-bit resolution- Accuracy: ± 0.02% of FSR- 7 TTL digital input
-
Product
PXI-8517, 2-Port PXI FlexRay Interface Module
780689-02
FlexRay Interface
2-Port PXI FlexRay Interface Module—The PXI‑8517 is designed for developing FlexRay applications. As part of the NI‑XNET platform, the PXI‑8517 works well in applications requiring real-time, high-speed manipulation of hundreds of FlexRay frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The PXI‑8517 contains two fully functional FlexRay interfaces, allowing an individual ECU to be connected to the interface when other cold-start nodes are not available. You also can use the interfaces individually to connect two separate FlexRay networks while maintaining full performance on each interface.
-
Product
H009 Module
M4KH009
Module
H009 modules can operate as a Central Computer Complex (CCC) and/or up to 16 Peripheral Units (PUs) simultaneously, or as a Bus Monitor. In addition, a Concurrent Bus Monitor enables concurrent monitoring of the bus during CCC and PU simulation. The module also supports error injection and detection, and all control parameters and data may be updated in real time. Note: The M4KH009 Module is a "double size" module, and occupies two vertically adjacent sockets in the EXC-4000 carrier Board.
-
Product
PXIe-7862, Kintex-7 325T FPGA, 16-Channel AI, 1 MS/s, PXI Multifunction Reconfigurable I/O Module
786672-01
Multifunction Reconfigurable I/O
PXIe, Kintex-7 325T FPGA, 16-Channel AI, 1 MS/s, PXI Multifunction Reconfigurable I/O Module - The PXIe-7862 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of timing and synchronization. With 16 analog input channels connected directly to a Kintex-7 325T FPGA, you have ample space to design applications that require precise timing such as hardware-in-the-loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXIe-7862 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware. The PXIe-7862 also includes peer-to-peer streaming for direct data transfer to other PXI Express modules.
-
Product
NI-9852, 2-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module
779707-01
CAN Interface
2-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module—The NI-9852 is a fault‑tolerant Controller Area Network (CAN) interface for developing FPGA-based applications with the NI‑RIO driver on CompactRIO. The NI‑9852 is ideal for low-level FPGA‑based control and triggering applications that are programmed using the LabVIEW FPGA Module. The NI‑9852 is ideal for byte-level manipulation of CAN frames using the LabVIEW FPGA Module. The NI‑9852 is only compatible with CompactRIO systems.
-
Product
Carrier Boards
ROM-DB5901
Carrier Board
ROM-DB5901 is an evaluation carrier board designed for the Advantech SMARC v2.0 module. It is compatible with the ROM-5720, ROM-5620 and ROM-5721 SMARC modules and has a multiple I/O interface for evaluation and development. It supports wide range operating temperatures, two power input interfaces, and two MIPI connectors for the camera module. ROM-DB5901 is an ideal development board for mobile applications, such as portable devices, industrial tablets or HMI systems
-
Product
32-Ch DPST 2A-125VAC 24VDC Multiplexer
YAV904X8
Multiplexer Module
The YAV904X8 features 32 channels of DPST relays distributed in 4-banks. The module uses electro-mechanical relays allowing each channel to switch current up to 2A and voltage up to 125VAC.
-
Product
PXI 8-slot BRIC Matrix, 2A, 2-Pole, 456x4, 8 Sub-cards
40-574-108
Matrix Switch Module
The 40-574-108 is a 456x4 2-pole matrix and is part of a range of BRIC matrices providing high density configurations capable of switching signals up to 2 A. The modules are available in 2, 4 or 8-slot PXI sizes and are constructed using high quality electro-mechanical relays.
-
Product
4 Channel DAC FMC Module
DACNF04 – HPC
-
Sundance Multiprocessor Technology Ltd.
The RFM-DACNF04 is a four channel Digital to Analog converter FMC which complies with VITA 57.1-2010. Each channel provides 16-bit input and one DC coupled single-end analog output with DC – 250KHz sampling speed based on Linear Technology’s LTC2704-16. The 16-bit input data for each channel is provided through SPI from the FPGA on the FMC carrier board. A single-ended TTL level trigger output is provided from the FPGA.
-
Product
Time-domain Field-Device-Circuit coupled simulator
EM-SUPREME®
-
Time-domain Field-Device-Circuit coupled simulator for modeling of passive structures, active components, and complete RF & millimeter-wave modules. EM-Supreme is used for EM modeling of power amplifiers, switches, filters, active antennas, and complete RF modules such as antenna-switch, switch-filter, switch-filter-amplifier, and front-end modules with no approximations.
-
Product
PXIe-4463, 51.2 kS/s, 2-Output PXI Sound and Vibration Module
783086-01
Sound and Vibration
The PXIe‑4463 offers high dynamic range and THD+N for audio, acoustic, and vibration applications. It provides the high precision and dynamic range necessary for the most stringent audio generation requirements in a modular form … factor. The PXIe‑4463 contains two 24-bit digital‑to‑analog converters to allow for fully differential simultaneous generation. Complete with three gain ranges, the PXIe‑4463 can generate current with programmable, per channel output configurations. The two timing engines allow you to perform multisample-rate applications on a single module and independently start and stop channels on a single module.
-
Product
CompactPCI
CPCI-ADDA
-
The CPCI-ADDA module offers a complete solution forhigh performance data acquisition applications. Boththe ADC’s and the DAC’s use 10 mS converters thatwill support up to 100khz signals. The CPCI-ADDAsupports P.I.D. loop closure frame rates of up to 4 KHzper channel. The CPCI host can download gain andsetpoint changes on the fly. The CPCI host can readback the current values for feedback, error, setpointand output drive on each channel. The local DSPprocessor can be used for data processing such asdigital filters and FFT’s. The DSP can also be used asa waveform generator to drive the 16 bit DAC.
-
Product
XMC-to-PCI Express Adapter
7769
-
Our XMC-to-PCI Express Adapter 1X w/ VITA 61 (XMC 2.0) Style Connectors (7769) permits the use of a single-wide XMC module in a 1X PCIe slot. PCI express lanes on the P15 XMC connector are routed to the male PCI express edge finger connector.
-
Product
PXI-2503 , 48‐Channel, 1-, 2-, or 4-Wire, Electromechanical PXI Multiplexer Switch Module
777697-01
Multiplexer Module
48‐Channel, 1-, 2-, or 4-Wire, Electromechanical PXI Multiplexer Switch Module—The PXI‑2503 is a PXI switch module that you can configure as a multiplexer or matrix switch by using different terminal block accessories. It uses electromechanical relays with low thermal offset for accurate measurements and offers a 1,024‐step scan list for deterministic scanning.
-
Product
PXI 12x8 RF Matrix 250MHz 75 SMB - With Loop-Thru
40-726A-751-L
Matrix Switch Module
The 40-726A is a 12x8 RF Matrix Module suitable for switching frequencies up to 300MHz (50Ω version). The 40-726A is available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The module is designed to provide a simple and scalable bidirectional matrix for RF frequencies. Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture. This maximizes isolation and RF performance.
-
Product
Peritec TestStand
-
Automatic test stand of Peritec is a product plus Peritec made LabVIEW module to optimize the use of automation of product evaluation NI tools TestStand. The module-based system using PXI, With savings available all over the state to be able to use from that day, the best evaluation system in line with customer requirements.
-
Product
PCIe Mini Module
PCIe-Mini-DIO16/32
-
The PCIe-Mini-DIO16/32 has 32 I/O channels that can monitor or control the on/off (high/low) status of up to 16 differential devices or up to 32 channels LVTTL, software selectable in groups of 2. Each channel can be used as an input or output.
-
Product
PXI 100 x Normally Closed Relay 1A 60W
40-145-201-NC
Relay
The 40-145/46/48 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector.
-
Product
PXI Programmable Resistor Card 2-Channel 2.5 Ohm to 8.19k Ohm - SPST
40-294-124
Programmable Resistor Modules
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI Very High Density Versatile 2 Amp Multiplexer
40-612A-002
Multiplexer Module
The 40-612A Very High Density Versatile Multiplexer module features a wide range of software selectable switching configurations. It is especially useful where a number of high density multiplexers are required with the option of easily altering the channel count as a test system evolves. Typical applications include signal routing in ATE and data acquisition systems. The 40-612 module uses high quality electro-mechanical relays, connections are made via a front panel 160 pin DIN41612 connector. The module can be software configured into one of a large number of different multiplexer modes. Relays allow the multiplexer banks to be set in 1 or 2 pole mode and inter-bank switching enables the channel count to be increased up to a maximum of 128
-
Product
Wired SIM Solutions
-
VPC's Snap-In-Modular (SIM) inserts offer multiple protocols, but share the same footprint, making them all compatible with VPC's 90 Series SIM module, iSeries SIM module, and i2 MX SIM model.SIM Infinity® inserts revolutionized the way PCB connections were made to the board with pass-thru technology and the ability to intermix multiple protocols in one module. SIM wired inserts expand that technology by offering even more protocols including micro coax, micro power, QuadraPaddle and VTAC; and coming soon, 20/26 GHz coax.
-
Product
PXI/PXIe High Density 2A Multiplexer, 8-Bank, 4-Channel, 4-Pole
42-614D-005
Multiplexer Module
The 40-614D-005 (PXI) and 42-614D-005 (PXIe) 8-bank, 4-channel, 4-pole multiplexers are part of the High Density 2A multiplexer module range available in 23 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
Modular Breakout System 78-Pin D-type Plugin Module for 40-197A
95-197A-001
-
The 95-197A-001 Plugin Breakout Module is designed to be fitted to a PXI 40-197A Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
