-
product
Programable Power Supply & Programable Electronic Load
EL-820P
*Digital button control and easy operation*High resolution(20mV, 10mA, 0.1W, 0.1Ω)*Overload prevention function*9 sets programmable memory*4 sets real time display*Voltage range: 1V~63V*Current range: 10mA~15A*Maximum power: 200W*Operation mode: CV, CC, CP and CR*Built in USB interface
-
product
PCI-7813, 3M Gate Virtex-II FPGA, Digital Reconfigurable I/O Device
779370-01
The PCI‑7813 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. The PCI‑7813 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware-in‑the‑loop (HIL) test, custom communications protocols, bit error rate test, and other applications that require precise timing and control.
-
product
Data Acquisition Systems
m+p Coda is a full-featured turnkey software platform for data acquisition, signal analysis and monitoring. Complete turnkey operation provides quicker time to test by eliminating costly application programming and long learning curves. The extensive built-in features and tools offer a functionality that was previously available only in custom packages. The intuitive graphical user interface facilitates set-up, operation and analysis, thus leading to precise, repeatable results quickly.
-
product
PXI Vehicle Multiprotocol Interface Module
PXI Vehicle Multiprotocol Interface Modules use hardware-selectable NI-XNET Transceiver Cables (TRC) to communicate High-Speed/Flexible Data‑rate CAN, Low-Speed/Fault Tolerant CAN, and/or LIN. Using the NI-XNET driver, you can create applications that require real-time, high-speed manipulation of hundreds of CAN and/or LIN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time. PXI Vehicle Multiprotocol Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
product
PXI Signal Generators (Signal Sources)
Accelerate test throughput with fast, high-quality measurements optimized for RF or microwave design validation & manufacturing testIncrease test configuration flexibility with a PXI platform and license key upgradesReduce development time with easy integration of drivers and programming examples into test environments
-
product
Radar Target Repeater
Series 8000
The Eastern OptX Series 8000 Radar Target Repeater is a portable, variable delay and propagation loss system designed for radar testing and alignment. The repeater may be remotely programmed in the field for dynamic operation. When connected to a user specified antenna the repeater can provide delays of up to 500 usec with a fixed delay, multiple discrete delays, or a progressive variable delay with amplitude control The Series 8000 features ultra wide bandwidth, low loss, high isolation, low noise figure, and high dynamic range.
-
product
Programmable Controllers Series
UniStream
Powerful programmable controllers with incredible HMI features—backed by the most efficient programming software you have ever used. Execute high-end projects — on time and within budget.
-
product
Test Systems
In-Circuit Test (ICT) tests populated circuit boards by means of electronic measurements through thin needles on test fixtures. We offer in-circuit testers for various testing strategies – from the flexible 19“ rack to the ergonomic high-performance tester. And all of our in-circuit testers are also available in the Lambda edition for true parallel testing. The flying probe test checks your printed circuit boards using four movable test heads. This requires no fixtures and allows for flexible test program generation. That makes our flying probe test systems ideal for a high mix of printed circuit boards and small to medium test volumes, such as for prototype testing.
-
product
SIMRC - Carrier Kit
1050-002
The SIM Relay Carrier 1050 simplifies the custom integration of small format embedded switching cards. No additional PCB design is necessary. Due to the Eurocard format the carrier can be fitted into a standard case or can be mounted in a 19" rack with side rails. Plug in standard SIM Relay Cards and control your switch application with the provided Soft Front Panel without any additional programming.
-
product
Test Executive & Development Studio
ATEasy
ATEasy is a test executive and a rapid application development framework for functional test, ATE, data acquisition, process control, and instrumentation systems. ATEasy provides all the necessary tools to develop, deploy and maintain software components - including instrument drivers, test programs, and user interfaces, as well as a complete and customizable test executive. It is designed to support and simplify ATE system applications with long product life cycles. With ATEasy, test applications are faster to generate and easier to maintain.
-
product
Mobile Comm DC Source w/ Battery Emulation
66321B
The Keysight Mobile Communications DC Source 663xx series offers several features ideal for testing wireless and battery powered devices. Excellent voltage transient response ensures maximum test-system throughput by minimizing device shutdowns due to significant voltage drops in the test wiring. Built-in advanced measurement system to accurately measure battery current drains when the device operates in different modes and a Keysight-developed feature that enables cellular telephone manufacturers to detect permanently and intermittently open-sense wire connections.The Keysight 66321B mobile communications dc source provides fast transient response, exceptional sourcing, output resistance programming, and precision measurement. This product is specially designed for testing next generation digital wireless communications products. The 66321B mobile communications dc source offers a new capability that simulates the internal resistance of a battery or battery pack. Additionally, these high performance models offer improved transient response and stable output operation with either short or long load leads.
-
product
NI-9871, 4-Port, RS485/RS422 C Series Serial Interface Module
779892-02
The NI‑9871 adds RS485/RS422 serial ports to CompactRIO systems. The serial ports are accessed directly from the FPGA to offer you flexibility in communicating with serial devices. The module has individual buffers on every port that save FPGA space and simplify programming. The NI‑9871 supports standard start bit, stop bit, and handshaking settings. It uses an external power to provide maximum compatibility and reliability under all serial port conditions.
-
product
NI-9870, 4-Port, RS232 C Series Serial Interface Module
779891-03
The NI‑9870 adds RS232 serial ports to CompactRIO systems. The serial ports are accessed directly from the FPGA to offer you flexibility in communicating with serial devices. The module has individual buffers on every port that save FPGA space and simplify programming. The NI‑9870 supports standard start bit, stop bit, and handshaking settings. It uses an external power to provide maximum compatibility and reliability under all serial port conditions.
-
product
Data Logger
The DeltaTrak FlashLink Mini Multi-Use Data Logger is ideal for customers looking for a low cost temperature data logger that can be programmed and reused. The FlashLink Mini Multi-Use data logger can be used in production and processing areas, or anywhere that tracking of temperature sensitive commodities or environmental conditions is needed. The data logger's sensor operates within a range of -40°C (-40°F) to 66°C (150°F).
-
product
Laureate Time Interval Meter
Model FRI
Configured to time periodic events which produce start and stop pulses from 1 s to 199.99 s over a programmed gate time up to 199.99 s. Timing resolution to 0.2 s. Optional data I/O and relays for alarm or control. Six 0.56" (14.2 mm) high digits, 1/8 DIN case.
-
product
Embedded Motherboards
ontrons embedded motherboards with a longevity up to 7 years are the ideal solution for a wide variety of applications.As the options for embedded computing continue to expand, choosing the right embedded motherboard becomes more complicated and confusing.In applications where permanence and risk avoidance must be optimized, Kontron's experience in a variety of markets leads customers to the solution that meets their critical programming and cost objectives.
-
product
8 Relay Output Board
APCI-2200-8
*8 relay output channels*Switching voltage 60 V/DC, 48 V/AC, switching current 1 A*Optical isolation*Watchdog*Easy programming
-
product
Test Device for Bicycle Batteries
ATGF 1500/PBG
The ATGF 1500 is a multifunctional testing instrument for bicycle batteries and accompanying battery chargers. The easy to use ATGF 1500 is suitable for battery systems of Derby Cycle, Gazelle, Simplon and ZEG. est programs: Quick Test, Capacity Test, Recalibration.
-
product
PXI Multiplexer Switch Module
PXI Multiplexer Switch Modules are ideal for high-channel-count applications that need to connect measurement or signal generation instruments to various test points on devices or units under test(DUTs or UUTs). PXI Multiplexer Switch Modules use a variety of relay types, including electromechanical armature relays, reed relays, field-effect transistor(FET) relays, and solid-state relays, each with their own benefits, allowing you to choose a multiplexer that fits your requirements. To program the switches, you can use the IVI-compliant NI-SWITCH driver software, complete with help documentation, example programs, and a soft front panel application for interactive control of switches. For intelligent management of complex switch systems, NISwitch Executive provides additional software tools to help you design, build, and deploy your switching system.
-
product
Universal Checkback Standalone System
UCBS
The Universal Checkback Standalone System (UCBS) provides periodic testing of "ON-OFF" carrier sets other than the TC-10B and the UPLC/UPLC-II (which incorporate this same checkback tester internally). The UCBS determines the functionality of the complete channel including the transmitters, receivers and associated coupling equipment. Periodic testing is required for the normally "off" channel, to provide warning of signal deterioration prior to needing it for relaying, The UCBS facilitates automatic testing of the channel at preset intervals. The UCBS is totally field programmable. All programming is done with a computer using the RS232 serial port or limited factory settings with switches on the Checkback module. Front panel LEDs indicate the factory or custom setting applied and the status of alarms.
-
product
DiodeTester
FECPLS500
Frothingham Electronics Corporation
The PLS500 automatic tester is designed primarily to do SURGE testing either as single pulses or with Forward and Reverse bias, according to methods 4066-1 or 4066-2. In addition, it can also test VF with rectangular pulses and THERMAL RESPONSE either in DVF (mV) or degrees per watt. All three test types may be performed in a single test program.
-
product
3000W-3200W 3-Phase Input Industrial AC-DC Power Supplies
TPS3000
The TPS3000 industrial AC-DC power supplies offer output power up to 3.2kW in a 2U high package with 3 phase supply input.Features include voltage and current programming, remote on/off, remote sense, a standby supply, PMBus communication, built in ORing FET and wide operating temparature range of -40°C to +70°C
-
product
Intelligent Mini Munitions Store Interface (MMSI) Module for Excalibur 800 Family of Carrier Boards
M8KMMSI
The M8KMMSI is an intelligent, Mini Munitions Store Interface [MMSI] module for the multimode, multiprotocol, Excalibur 8000 family of carrier boards. Each module of the M8KMMSI contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory mapped and may be accessed in real time. Each M8KMMSI module may be programmed to operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT/Concurrent Monitor and Bus Monitor.The M4KMMSI comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
product
Software Engineering Services
Reston Software provides state-of-the-art, U.S.-based software development services. We can fulfill your immediate and long-term software development needs by creating new applications, supporting and enhancing existing applications, and modernizing legacy applications.We focus primarily on Microsoft technologies: .NET, WPF/XAML, Visual C++, COM/ATL, ASP.NET, Microsoft Office plug-ins.We also specialize in upgrading legacy programs to modern environments. We are experienced in upgrading Visual Basic programs (from version 2.0 and higher) to the latest version of VB.NET, and in upgrading Windows NT, 2000, and XP applications to Windows Vista, 7, and 8.
-
product
ICT Tester
Adapter design, assembly and validation for Agilent, Keysight, HP, Checksum, Spea. Preparing and debugging ICT scripts. ISP Programming Integration. Integration of edge scan testing, Jest testing, digital testing, semi-functional testing, IC programming, FINN probes, and more
-
product
Serial Controlled Relays And Relay Drivers
*ICS's Serial controlled Relay Interfaces provide the user with a choice of 16 contact closures or 16 relay driver outputs for driving external relays. All of the Serial to Relay Interfaces include 8 isolated digital inputs. Available in ICS's Minibox™ or as an OEM board.*All interfaces are IEEE-488.2 compliant and use SCPI commands for operation with NI or Agilent VISA, LabVIEW and VEE or any Serial programming language. Use ICS's interactive Serial Keyboard program for easy operation from your PC without having to write a program.
-
product
ApTest Services
Applied Testing and Technology, Inc.
We undertake projects ranging from short term engagements to long term partnering, for customers from startups to the Global 1000. Many ApTest projects encompass a complete outsourced test design and development program, while others involve assisting a client with defining or implementing in-house testing programs.
-
product
Stand Alone Low Voltage Tester
Model 256/PC
Internal Memory: 8 program locations without test point labels or 2 program locations with test point labels. Removable Memory: 16 program locations without test point labels, or 4 program locations with test point labels.
-
product
50 MHz to 18 GHz USB Peak and Average Power Sensor
U2021XA
The U2020 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming.
-
product
DLMS Meter Reading App
Signals & Systems India Private Limited
The DLMS meter reading application runs on Android mobile devices. It is an effective and efficient meter reading solution for DLMS meters (IEC-62056) & Smart meters (IS-16444). This application supports reading and Real-time viewing of field meter profiles, data view, programming the meter, smart meters connect/disconnect. This is also a solution to address the last mile connectivity issues- where the AMR and AMI networks failed due to network problems.
