DC DC Converters
-
Product
Millimeter Wave Converter
ZVA-Z Series
-
Millimeter-wave measurements in the V, E, W, F, D, G, J and Y band – network analysis in frequency ranges from 50 GHz to 500 GHz depending on the converter model. Featuring a wide dynamic range, the RPG converters offer high operating convenience and allow fast measurements. Two-port measurements can be performed using a four-port network analyzer and two converters; no external generator is required. When using a two-port network analyzer, an external generator is needed to supply the LO signals.
-
Product
Variable Transformer DC Power Supplies
-
Variable DC power supplies are AC to DC power supplies with a variable DC output. The output can be varied with a Variable Transformer (also known as variac). The Variable Transformer can be adjusted manually or with a motorized control. The AC input power can be single phase or three phases. With single phase AC input, the DC output ripple is very high (50%). With three phase AC input, the DC output ripple is low (5%). This would be a key benefit for selecting three phase AC input instead of single phase.
-
Product
Programmable DC Current Source
Model 121
-
The Model 121 programmable DC current source is a precision instrument suitable for bench-top use or panel-mounted operation in labs, test facilities, and manufacturing environments. It provides a low-noise, highly stable source of current up to 100 mA, with convenient manual selection through 13 pre-set output levels, each representing a ten-fold change in power when attached to a resistive load. A “user” setting allows the current output to be defined anywhere within the operating range of the unit, from 100 nA to 100 mA.
-
Product
High Power DC Electronic Loads
63200A
-
Chroma Systems Solutions, Inc.
Chroma High Power DC Electronic Loads provide wider operating voltage and current ranges up to 240kW, sine wave loading, dynamic frequency sweep to 50kHz, digitizing, MPPT, an impressive front panel that tilts, and the highest accuracy available (voltage 0.015% + 0.015% F.S. and current 0.04% + 0.04% F.S.) – all with an incredibly high power density (6kW @4U).
-
Product
S.O. DIMM Converter
DDR 200-pin
-
The RAMCHECK DDR 200-Pin Converter is a perfect low-cost solution for testing modern laptop DDR memory. The converter plugs directly into the 184-pin RAMCHECK DDR main adapter, providing you with fast, convenient testing capabilities
-
Product
DC/DC Converter 150 W
CQB150W-110S48
-
DC/DC converter with 150 W from Cincon | input ranges 43 - 160 VDC | output 48 V | operates in temperature from -40 to +105 °C | according to EN45545-2 fire and smoke
-
Product
Standard Mechanical Calibration Kit, DC To 7.5 GHz, 7–16 (male)
85038M
Mechanical Calibration Kit
Modern wireless communication systems require high-performance components offering low VSWR and low intermodulation distortion at high transmit power levels. To meet these needs, 7-16 connectors are becoming increasingly common in base station transmitters, amplifiers, duplexers, and other products. These connectors conform to IEC 169-4, DIN 47223, European standard EN 122190, and British standard BSEN 122190.
-
Product
DC Power Supply
PW-3032R
-
*Toroidal Transformer*Low EMI & High EMS*Very Low Ripple & Noise*30V/3A+5V/3A Dual output.*<0.3m Vrms Ripple & Noise(C.V.)*<2m Arms Ripple & Noise(C.C.)*Low EMI & High EMS.*Dual Display.
-
Product
Digital to LVDT RVDT Converters
DLVT
ITA
Computer Conversions Corporation
The SLVT Series are complete, low profile, continuously updating, single channel, Isolated Digital to LVDT Converters used to simulate the output of LVDT's (Linear velocity displacement transducers), RVDT's (Rotary...) and other phase/voltage sensitive AC devices.
-
Product
Coaxial Switch, DC Up To 26.5 GHz, SPDT
N1810TL
Coaxial Switch
The Keysight N1810TL latching coaxial switch combines unmatched flexibility of configuration with excellent repeatability, long life, and reliability.
-
Product
DC Blocking Power Splitter Combiner
PD7130
-
INSTOCK Wireless Components, Inc
True 3 Way Equal Split and BalanceWideband Frequency, 698-2700 MHzHigh Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)50 VDC maximum on DC block portTri Alloy SMA Female (Jack) Low PIM
-
Product
DC/DC Converter 120 W
CTS-120-6867-D
-
DC/DC converter with 120 W from Premium | input ranges 14.4 - 30 VDC | output 24 V | operates in temperatures from -25 to +85 °C | designed according to EN50155
-
Product
Low PIM Coaxial Switch, DC to 4 GHz, SP6T
87106P
Coaxial Switch
Low passive intermodulation (PIM) is crucial for applications where two or more transmitted signals share a common antenna or whenever the transmitter signal is too high or the receiver is sensitive to high intermodulation. The Keysight 87106P is a low PIM SP6T coaxial switch, operating from DC to 4 GHz, which can help to keep the system PIM level low. A guaranteed 0.03 dB insertion loss repeatability and 3 million cycles of operating life ensures signal integrity, improves testing efficiency, and ultimately maximizes test throughput.
-
Product
Economy Mechanical Calibration Kit, DC To 3 GHz, Type-F, 75 Ohm
85039B
Mechanical Calibration Kit
The Keysight 85039B calibration kit, with option M0F, contains male and female type-F open, short, and load standards. This calibration kit works with all 75 ohm network analyzers and test sets for measurement of devices with 75 ohm type-F connectors. The kit also includes type-N to type-F adapters. More economical versions of this kit are available by ordering option 00F for the female standards only, or option 00M for the male standards only. This kit is specified from dc to 3 GHz.
-
Product
USB Converter Cables
-
These converter cables connect various serial interfaces to a computer USB port.
-
Product
DC Power Supply
-
A device that converts electrical energy from a source into a constant, unidirectional flow of low-voltage DC power to operate electronic devices.
-
Product
DC Blocks From 0.1 MHz To 18 GHz
-
Pulsar Microwave Corporation's DC blocks are designed to inner-only topology and utilize our standard housings for fast turn manufacturing. Designs are tested to 50 Ohms, and models range up to 18 Ghz with a maximum voltage rating of 500 Vdc.
-
Product
I/O's & Converters
-
Rishabh Instruments Pvt. Ltd.,
Module of logic outputs. Control of actuators from monitoring systems or PLC over RS485. 4 relay outputs or 8 OC outputs steered through RS-485/Modbus. Fixing on a TS35 rail. Full galvanic separation between outputs (for relay outputs). Configuration through free LPConfig software.
-
Product
DC Power Supply
MPP-2K/3K Series
-
MPP Series DC power has a maximum output voltage/current of 1000V/100A, a maximum power of 8kw, and a standard 2U/3U chassis for easy mounting.
-
Product
Dynamic D/A Converter, 16-channels, 16-Bit, Unipolar, 30 V/20 mA
M9188A
Digital / Analog Converter
The M9188A is a PXI based, 1-slot unipolar Dynamic DAC which has 16 channels capable of supplying typical waveforms at high voltages. It has 4 isolated banks with 4 channels in each bank.
-
Product
Frequency Converters & Transceivers
-
Mercury Systems’ converter and transceiver products are at the forefront of SWaP-optimized RF integrated products. Through substantial R&D investment and a library of building blocks, Mercury Systems has the capability to rapidly execute on the most complicated of custom transceiver designs. As the OpenVPX industry leader, Mercury Systems knows how to make integration into your system a breeze.
-
Product
LED DC Electronic Load Simulator
3340G Series（150W~300W）
-
Each 3340G Series module has its own control and display panel, LED/CC/CR/CV/CP/ Dynamic modes, plug in 3300F with 150 sets Store/Recall memory which provides load set-up more efficiently，also can be controlled intranet via RS232、Ethernet、USB and GPIB interface.
-
Product
Coaxial Switch, DC to 4 GHz, SPDT
8762A
Coaxial Switch
The Keysight 8762A offers excellent electrical and mechanical performance with broadband operation, high isolation, low SWR, long life, and exceptional repeatability.
-
Product
Adapter, 1.0 mm (m) to 1.0 mm (m), DC to 110 GHz
11920A
Coax Adapter
The Keysight 11920A precision 1.0 millimeter waveguide-to-coax adapter offers a simple way of measuring coaxial devices at higher frequencies. It is designed for the measurement of components with 50 ohms impedance and frequency range from dc to 110 GHz.
-
Product
High Speed DC Electronic Load
6330A series
-
The 6330A family offers 8 types of modular loads with power ranging from 30 watts to 1200 watts, current from 0.5mA to 240A, and voltage measurement from 0.5mV to 500V. Each load is isolated and floating, programmable in dual current range and measuring voltage range, and capable of synchronizing with other modules for control operating. The load can be operated in constant current, constant voltage, and constant resistance. With Synchronic parallel control capability, 6330A series loads allow users to parallel and synchronize more than one load together from an internal loading control signal. This feature provides synchronic dynamic loading test for multi-output power and high power test solution. Real time measurement of voltage, current, is integrated into each 6330A load module using a 16-bit precision measurement circuit. The user can perform on line voltage measurement and adjustment, or simulate short circuit test using the simple keypad on the front panel.
-
Product
L Band Splitter, DC Block All Ports
PD5142
-
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.4 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)50 VDC maximum on DC block portsTri Alloy SMA Female (Jack) Low PIM
-
Product
DC/DC Converter 140 W
CTS-120-6887-D
-
DC/DC converter with 140 W from Premium | input ranges 21.6 - 47 VDC | output 24 V | operates in temperatures from -25 to +85 °C | designed according to EN50155
-
Product
Programmable High Power DC Power Supply
ADG series
-
Preen’s ADG series is a programmable DC power supply with high power density and high output power, and offers many great advantages on response time, accuracy and output voltage range. ADG is an excellent source for testing or facility type applications, such as aerospace, renewable energy, automated test system, battery and server. With power level up to 80kW per unit, the ADG series provides output voltage up to 1000V and high output current of 2000A after custom modification.
-
Product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-02 And WMA-02LF
-
The Falco Systems WMA-02 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 4mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-02LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.2mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Product
Standard Mechanical Calibration Kit, DC To 7.5 GHz, 7-16
85038A
Mechanical Calibration Kit
The Keysight 85038A calibration kit contains open circuits, short circuits and terminations with both male and female 7-16 connectors and has frequency coverage from dc to 7.5 GHz (usable to 8 GHz).
