-
Product
Probe Station
EPS1000
-
Reasonable price and compact design. - Sellectable chuck size : 4inch, 6inch, 8inch when ordering probe station. - Hot chuck can be installed. Temp range: RT ~ 300°C - Hot and cool chuck from 0 °C ~ 300 °C can be provided. - Maximum pcs of manipulators can be installed on the base unit of probe
-
Product
32 Channel, 1 Form C 2A Relay Switch
DP-cPCI-4509
-
The DP-cPCI-4509 is a 32 channel relay switch module. This module is constructed using 2 Form ‘C’ (DPDT) relays. It provides for 250V DC isolation between channels. Out of the two contacts in each relay, one is used to provide the status of the relay through read back and the other is used for switching purpose. The user can write the command for the selected channels on to the Primary latch of the FPGA section. Readback is available to confirm the selected commands.
-
Product
Cable Assembly, 9-Pin D-Type, Male to Unterminated With Cut Ends, 0.5m, HV
A009DM5-C-HA050
Cable Assembly
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation.
-
Product
Chilled Mirror Hygrometer
DewMaster
-
One, two or three stage sensors available - integral or remote from controller.NIST traceable calibration certificate.Depression range choice of either 45, 65 or 95°C . (one, two or three-stage cooling)Automatic Balance Control (ABC)
-
Product
Ultrasound Detector/Recorder
D500X
-
The D500X Mk II is as easy to use and provides the same features as the classic D500X, with the following exceptions:*It does not include an internal microphone. Instead it ships with an external microphone which is either directly connected to the microphone jack or through an extension cable (sold separately). The microphone jack is an XLR type so no adapter cable is required.*It is powered by 4 C type batteries which last roughly three times longer than the AA batteries used in the classic D500X.*The jack for external power is a standard 2.5 mm DC power jack for easy connection.
-
Product
NI-9234 and cDAQ-9171 USB Sound and Vibration Measurement Bundle
865664-01
Sound and Vibration
NI-9234 and cDAQ-9171 USB Sound and Vibration Measurement Bundle - The USB Sound and Vibration Measurement Bundle with NI-9234 and cDAQ-9171 includes the NI-9234 C Series Sound and Vibration Input Module and the cDAQ-9171 CompactDAQ Chassis for sound and vibration measurements. This bundle provides a portable, USB-based sensor measurement system that helps you measure signals from integrated electronic piezoelectric (IEPE) and non IEPE sensors such as accelerometers, tachometers, and proximity probes. The included NI-9234 features 4 channels with built-in anti-aliasing filters that automatically adjust to your sample rate. Additionally, when used with NI software, the bundle provides processing functionality for condition monitoring such as frequency analysis and order tracking.
-
Product
75-Watt AC/DC Power Supply; Single Output
56KS1
Programmable Power Supply
NAI’s 56KS1 is a 75 Watt AC/DC Power Supply that accepts multiple AC inputs plus a +270 VDC input. This COTS unit provides full-power, single output, at a baseplate temperature of +85° C.
-
Product
Multi Interface USB Adapter
SUB-20
-
SUB-20 is a versatile and efficient bridge device providing simple interconnect between PC (USB host) and different HW devices and systems via popular interfaces such as I2C, SPI, MDIO, RS232, RS485, SMBus, ModBus, IR and others. It is also a full "any to any" converter between all supported interfaces and I/O features. SUB-20 is a powerful I/O controller with 32 GPIO, 8 Analog Inputs, PWM Outputs, Edge DEtectors, LCD, Leds and push buttons.SUB-20 system includes SW package containing driver, API Library, GUI and Command Line based applications, C,C++,C#,VB.net, MATLAB, LabView sample code and documentation. SUB-20 can be used with PC 64/32 bit running Windows 2000/XP/Vista/Win7/Win8, MacOS, Unix/Linux and DOS.Working with SUB-20 does not require deep knowledge of low layers of the specific interface. All you need to do is to call right API function at the right place. And this is really very easy as API functions are well documented and "exampled". API set is relatively small but comprehensive.SUB-20 is equipped with status Leds, optional LCD and buttons. All this guarantee fast and comfortable development, field debugging and maintenance of applications including option of standalone operation.
-
Product
NI-9212, 8-Channel, 95 S/s/ch Simultaneous, ±78 mV C Series Temperature Input Module
785259-01
Temperature Input Module
8-Channel, 95 S/s/ch Simultaneous, ±78 mV C Series Temperature Input Module - The NI‑9212 offers channel‑to‑channel, isolated thermocouple input channels. The NI‑9212 channel‑to‑channel isolation protects channels from continuous voltages up to 250 Vrms and transient (withstand) voltages up to 1500 Vrms. You can use the NI‑9212 in a variety of applications that are not conducive for bank-isolated channels such as white goods testing, in-vehicle data logging, battery stack testing, as well as in various other noisy industrial environments.
-
Product
AC/DC Power Supply 60 W
TR100M150
-
AC/DC power supply with 100 W from Cincon | input ranges 90 - 264 VAC | output 15 V | operates in temperature from -20 to +80 °C | provides 2 MOPP
-
Product
Bipolar Power Transistors
-
A wide variety of products are rolled out, for example, for uses at high temperature (up to 175°C applicable), high power, and low Vce (sat), and others.
-
Product
Sound Level Meter, 40 dB, 130 dB, 3.5 dB, 0.1 dB, 40 °C, 0 °C
72-935
-
The 72-935 is a Compact Digital Sound Level Meter, measures less than 6-inch length, including the windscreen and provides full 40 to 130dB measuring range. Perfect for numerous types of measurement including sound system testing and noise level monitoring.
-
Product
ARINC 429 Test And Simulation PCIe Module
PCIe-C429
-
*4, 8, 16 or 32 software programmable TX / RX channels*X4 lane PCI Express host interface*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*Sorting according to SDI field*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
Product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Cut Ends, 2m HV, Exit Towards Pin 1
A050DF5-C-HA200
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Door Contact Sensor
ENVIROMUX-M-DCS
-
Monitors access with a magnetic bridge sensor, which responds to any magnetic material (no special inserts necessary). Can also be used for monitoring side wall and covers. Includes mounting hardware. For normally closed circuit connection. 2-wire interface. Screw terminal. Maximum cable length: 1,000 ft. Wide actuating gap, approximately 1". Dimensions WxDxH (in): 0.5x0.5x2 (Switch), 0.5x0.5x2 (Magnet). Operating temperature: 32 to 158°F (0 to 70°C). Regulatory approvals: RoHS.
-
Product
Environmental Testing
-
Educated Design & Development, Inc.
Incredible size / features at a phenomenal price! A must have when a larger chamber is needed. Easy to use, microprocessor based digital controls. Standard models are heat/humidity Humidity range of 10-96%, temperature range of 35°-70° C, Refrigeration can be added for cold testing to -10°. Chamber inside dimensions are 34x28.5x60 in. (87x73x153 cm), many options are available including chart recorder, RS232, programmable ramp/soak, viewing window and CO2 system.
-
Product
Temperature Measurement IR Sensors & Detectors
ST120 TO-5
-
A single-channel silicon-based thermopile provides lowest cost solutions in a small active area of 1.2mm x 1.2mm in a TO-5 package. Time constant of 25ms with Nitrogen encapsulation gas. Delivers a very low Temperature Coefficient of Responsivity of -0.04%/C. This detector has a very short thermal shock response to ambient temperature change.
-
Product
AC/DC Power Supply 60 W
TR100M200
-
AC/DC power supply with 100 W from Cincon | input ranges 90 - 264 VAC | output 20 V | operates in temperature from -20 to +80 °C | provides 2 MOPP
-
Product
Imaging
SLA64 (Preliminary)
-
A 1 x 64 element silicon-based thermopile array. Each active area is 0.45mm x 2.0mm with a time constant of 42ms and a low Temperature Coefficient of Responsivity of -0.06%/C. It is packaged in a 68-pin QIP. Includes internal 30k 5% NTC chip thermistor provides ambient package temperature measurement. See Thermistor Options p/n: MT04.
-
Product
Hillgus for Windows™
-
Ingenieurbüro Dr. Hillger Ultrasonic-Techniques
*Fast imaging with A-, B-, C-, and D- scans*(A-scan-software) and for ultrasonic imaging (generating of Full-wave-scan option*Hillgus controls the HFUS 2XXX-, HILL-SCAN 3XXX- and all USPC XXXX- systems *Easy to handle, shortcut- and menu- driven functions *Hillgus for Windows™ is the digital high resolution and fast data acquisition package for evaluation of A-scans 1 (A-scan-software) and for ultrasonic imaging (generating of C-, D-, and B-scans). *Hillgus for Windows™ controls ADC-boards up to 5 GSamples. *Hillgus for Windows™ combines the control of motion and of ultrasonic systems, serves to data acquisition and data analyses.
-
Product
Desktop Tunable Laser Source
UC8110
-
The UC8110 desktop tunable lasers offer superior performance for the test of DWDM components, AWG & PLC components, optical amplifiers, DWDM system and other general purpose of fiber optical test and measurement applications. It is a wavelength high accuracy, high power output, small dimension, fast startup, affordable tunable laser source system. UC INSTRUMENTS provides C band, L band, or C+L band tunable laser sources options.
-
Product
UV TOCONs
-
SiC based UV sensor with integrated amplifier and 0 – 5 V voltage output. Measures intensities from 1.8pW/cm² up to 18W/cm². Spectral response for broadband UV or filtered for UVA, UVB, UVC or UV-Index. Also available for blue light (GaP chip) or visible light (Si chip) measurement. Available in TO5 housings or as miniature sensor probes (stainless steel or plastic). Special TOCONs for hydrogen flame sensing (TOCON_F) and for fire detection (TOCON_N) available. Also available for operating temperatures up to 120°C (standard is 85°C). Please learn more about the sglux TOCONs here: TOCON selection guide and here: TOCON User Guide.
-
Product
Automotive-grade Diodes
-
ST's portfolio of automotive diodes is qualified to the AEC-Q101 standard and is intended for DC-DC converters used in numerous automotive functions. Most of these dedicated diodes are guaranteed in operation at junction temperatures as low as -40 °C and as high as +175 °C. The automotive-grade diodes belong to our STPOWER family.
-
Product
Hamburg Wheel-Tracking Tester
-
The Hamburg Wheel-Tracking Tester is used to test submerged, compacted Hot Mix or Warm Mix Asphalt specimens as per standard.The device consists of a reciprocating wheel that is rolled over the specimens while measuring the rate of permanent deformation. A constant load of 705 N ±4.5 N is applied to the specimens with a sinusoidal wheel speed of 1 ft/sec in a constant temperature controlled water bath up to 70 °C (± 1.0 °C). An LVDT jig is used for continuous measurement of permanent deformation along the path of the rolling wheel. Accommodates cylindrical or slab specimensSoftware for automatic determination of Stripping inflection PointNumber of passes to SIP, number of passes to failure and other calculated parametersStainless steel construction with temperature controlled water bath up to 70ºC
-
Product
Multimeter, Tester, LCR
-
7 digit resolution.Highly sensitive DCV and resistance measurements with 100 pV and 100 nOhm.1.3 nV eff , 8 nV peak-peak noise performance.Built-in low-noise 2-channel scanner.Direct SPRT, RTD , thermistor and thermocouple temperature measurement with 0.003 C accuracy.3 built-in low-power, dry-circuit test resistance functions.GPIB and RS232 interface.
-
Product
SIL Reed Relays
Series 105
-
• SoftCenter™ construction• Highest quality instrumentation grade switches• Encapsulated in a plastic package with internal mu-metal magnetic screen• Wide range of switch confi gurations -Form A, 1 Form B, 2 Form A, 1 Form C• Two pole relay requires the same board area as the single pole type• Dry and mercury wetted switches are available with the same pin configuration and footprint.• Many benefits compared to industry standard relays. Learn more here >.• Insulation resistance greater than 10E12 Ohms (1TOhms) for dry Form A devices• 5, 12 and 24 Volt coils are standard, with or without internal diode• 100% tested for dynamic contact resistance
-
Product
sbRIO-9236, Non-Enclosed, 10 kS/s/channel, 350 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module
781580-01
Strain/Bridge Input Module
Non-Enclosed, 10 kS/s/channel, 350 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module - The sbRIO‑9236 measures dynamic strain on all channels simultaneously, allowing for synchronized, high-speed measurements. This capability is important for applications, such as impact tests, that require comparison across many channels at a particular instant in time. The sbRIO‑9236 includes built-in voltage excitation for quarter-bridge sensors. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. Non-enclosed modules are designed for OEM applications.
-
Product
Functional Testing For Critical Software
RapiTest
-
*Requirements-based testing for Ada, C & C++ on-host & target*Reduce test authoring effort through easy-to-use test formats*Manage project artifacts with requirements traceability*Simplify verification through integration with your CI tool*Produce evidence for DO-178 and ISO 26262 certification
-
Product
Conductivity / TDS Monitor / Controllers
750 Series II Conductivity Monitor & Controllers
-
The unique circuitry of the 750 Series II Conductivity Monitor/controllers guarantees accurate and reliable measurements. Drift-free performance is assured by “field proven” electronics, including automatic DC offset compensation and highly accurate drive voltage. Since temperature compensation is at the heart of accurate water measurement, all Myron L® Monitor/controllers feature a highly refined and precise TC circuit. This feature perfectly matches the water temperature coefficient as it changes. All models corrected to 25°C. The TC may be disabled to conform with USP requirements.
-
Product
AC/DC Power Supply 50 W
HBU50-109
-
AC/DC power supply with 50 W from Sinpro | input ranges 80 - 275 VAC | output 32 V | operates in temperatures from -10 to +70 °C | provides 2 MOPP protection
