Solar Array
field of panels.
-
Product
Solar Radiation Meter
MacSolar E
-
The measuring device has been designed primarily for engineers, architects, fitters and measurement technicians. The MacSolar E allows both an indication of the current irradiance as well as an estimate of the solar installation yield.
-
Product
Testing for Si Solar Cells Using High Performance CCD
EL Imaging Tester
-
EL Testing for Si Solar Cells using High Performance CCD. The determination of luminescence (photo emissions) in solar cells is an important characterization tool. Typical solar cells often have defects which limit the efficiency or lifetime of a cell. Many of these defects are visualized with Luminescence Imaging. By using this technique, the manufacturing process can be optimized to produce better cells. Luminescence Imaging takes advantage of the radiative inter-band recombination of excited charge carriers in solar cells. The emitted photons can be captured with a sensitive CCD camera to obtain an image of the distribution of the radiative recombination in the cell. This distribution is determined by the local excitation level, allowing the detection of electrical losses, thus mapping the diffusion length of minority carriers as the emitted light is low intensity and in the near infra-red range, the CCD camera has a high sensitivity wavelength from 900 to 1100 nm with little thermal noise. This CCD camera provides excellent resolution of 1024 x 1024 pixels with a large 1μm pixel size, multi-megahertz readout speed, and robust USB 2.0 connectivity. The EL CCD Camera is the ultimate high-performance CCD camera for electroluminescence and photoluminescence imaging for Photovoltaic (PV) Cells and Modules. This camera combines low noise electronics and optimal sensitivity in NIR.
-
Product
Daystar Solar Meter
DS-05A
-
Daystar's DS-05A solar meter brings 'point and read' simplicity to the measurement of solar irradiance. Just turn the meter on, point the sensor at the sun and obtain a reading in Watts/m2.
-
Product
Solar simulation systems
-
Whatever your application, from an environmental chamber for small components to an extensive array for a complete automobile or aircraft test, EYE / Iwasaki has the experience to provide a solar lighting system customized for your requirements.
-
Product
Solar Radiation (Sunshine) Test
-
This test determines the effects of direct solar radiation on components and material. The heating effects of solar radiation differ from those of high air temperature in that the amount of heat absorbed depends on the roughness and color of the surface on which the radiation is incident and the angle of incidence to the sun. Variations in the intensity of solar radiation over the surface of the component, may cause components to expand or contract at different rates, which can lead to severe stresses and loss of structural integrity. In addition, degradation due to photo-chemical changes can occur such as fading of color, deterioration of natural and synthetic elastomers and polymers. The test items that are subjected to solar radiation testing are those that are exposed to solar radiation during its life cycle, in the open, in warm climates.
-
Product
Linear Array
-
Linear array sensors consist of a linear array of integrating photosensing pixels which measure incident light over a user-defined exposure time and generate a voltage or digital output which represents the light exposure at each pixel. The sensors are available in a variety of lengths and pixel resolutions. The analog output may be directly interfaced to an ADC for digital processing or for comparing black/white thresholds. Applications include contact image sensing, optical character recognition, edge detection, and object measurement in products such as copiers, document scanners and spectroscopy.
-
Product
Solar Radiation Sensors & Transmitters
A70 Series
-
The Comptus A70 Series solar radiation sensors with transmitters are available in two models. The A70-A PAR Sensor measures photosynthetically active radiation (PAR) in the 400 to 700 nm range. The A70-I Insolation Sensor measures solar radiation in the 280 to 2800 nm range. The signals from the sensors are scaled by the signal conditioner to provide the desired output.
-
Product
Solar Simulators
-
Abet Technologies offer a wide range of ASTM, IEC, and JIS standards compliant solar simulators ranging from 150W to 3kW with one sun or greater illuminated field sizes from 50 x 50 mm to 35 x 35 cm. The direction of illumination, traditional down pointing, horizontal, or vertical up pointing can be specified at the time of ordering.
-
Product
6″ (15.25 cm) 1000W Pre-Irradiation Solar Simulator
Model LS1000-6S-009
-
1000W Pre-Irradiation Solar Simulator Kit specifically designed for the pre-irradiation step during in vitro broad spectrum sunscreen testing. Fully compliant with the most current FDA and ISO requirements. The 6″ (15.25 cm) Class A beam can irradiate up to 9 PMMA plates simultaneously.
-
Product
SINE M-14 Sinusoidal Array
-
The Sinusoidal Array SINE M-14 was designed for various electro-optical applications, particularly where a small array is needed to fit into the frame. It can fit into an 18mm diameter circle or into a standard 35mm motion picture frame.The lines in the SINE M-14 lie perpendicular to the length of the film. In addition, the pattern is available on a wider film (without perforations) cemented between glass (TM-G options) both the .6 (-60) and .8 (-80) modulations.
-
Product
FBG Arrays & Cables
-
Technica Optical Components, LLC
Our Fiber Bragg Grating Arrays are available in a wide range of optical specifications. Our optical FBG cables consist of an array of Fiber Bragg Grating sensors. All our Fiber Bragg Grating Arrays and Cable models are designed to make handling and deployment fast, easy and intuitive. Technica undertakes a rigorous development process before products release. We are committed to continuous improvements after release to insure performance to the highest of standards.
-
Product
Coupled Multielectrode Array Sensor (CMAS) Probes
-
CMAS probes are made from user-specified sensing materials, including carbon steels, stainless steels, and nickel-, aluminum-, and copper-based alloys. They can also be made from customer supplied materials that have the same microstructure/heat treatment as the system component materials to be monitored. The size of the sensing electrode varies from 0.1 to 3 mm (0.004" to 0.12") in diameter, depending on the application. Typical numbers of electrodes in a CMAS probe are 9, 16 or 25 for online corrosion monitoring and vary from 8 to 100 for laboratory corrosion and electrochemical studies.
-
Product
Solar simulators
-
Solar simulators enable the measurement of (dark and) light IV characteristics and of power and efficiency of photovoltaic An artificial light source is used to create illumination conditions that are similar to those in natural sunlight. International standards hosted by ASTM, IEC and JIS allow to classify the properties of a solar simulator with respect to spatial light uniformity, spectral content of the light and time variation of intensity.
-
Product
SINE Sinusoidal Vision Demonstration Array
-
The Sinusoidal Visual Demonstration Array is designed to demonstrate the Modulation Transfer Function (MTF) of the human eye. Its transmittance varies sinusoidally and increases in spatial frequency from 0.2 to 20 c/mm, following a logrithmic scale. The modulation increases linearly from top to bottom. One can see, in the image, where the visual contrast contour disappears which is the MTF of the eye. Ideally suited for teaching and demonstration, the Array is available on film mounted in glass (-G), or mounted in a 2″x 2″ projection slide.(-SL)
-
Product
Flashlight Solar Simulator
-
Flashlight Solar Simulators have the advantage of negligible temperature change to the solar cell. For this reason, they are primarily used in cell and module production environments. Also, they are a more budgetary alternative if large cell areas are to be illuminated, because it is easier to have excellent light uniformity on areas of 8 in x 8 in or larger. So, this type of solar simulator is also used for analysis of large area thin film solar cells. But care must be taken, as some materials (e.g. CIGS) have long inherent time constants, so that the pulse length (better: flash plateau) must be chosen accordingly.
-
Product
Array Solutions K9AY Loop Wire/Mast Kit
AS-AYL-4 WM
-
All materials required for the installation of your receiving loop system, have been included in this kit with the exception of those items listed below under the heading; ‘You will also need. ‘ The specified 8’ x 5/8” copper-clad steel ground rod can be purchased at just about any local hardware store or home center.
-
Product
Single Long Pulse Solar Simulator & I-V Test System
TriSOL SLPSS
-
The OAI Test System for HIGH EFFICIENCY SOLAR CELLS overcomes the limitations of flash testing by providing a highly optimized pulse width and voltage sweep rate to match the cell’s dielectric response speed. As a result, the system produces extremely accurate measurements of solar cell efficiency leading to increased profitability.
-
Product
Single LED Arrays | Green | 2 Or 10 MA
LED-S-g-2/10
-
Pre-mounted single LED, high luminosity with low power consumption and adapt to DIN41494
-
Product
Workhorse Waves Array
-
Teledyne Marine RD Instruments
Workhorse Waves Array is an innovative, cost-effective upgrade that allows you to take your Teledyne RDI ADCP to the next level. Via a simple upgrade, you can capture not only the industry’s most field-proven and dependable precision current profiling data, but highly accurate multi-directional wave measurements as well.
-
Product
Solar Cell Tester
REOO RO-GTM2615
-
REOO RO-GTM2615 Solar Cell Tester is designed for PV cell manufacturing inspection, enabling fast cell performance inspection and stable electrical quality verification. Built for solar factories, it improves cell testing accuracy and maintains stable operation across PV cell production lines.
-
-
Product
SparkFun IR Array Breakout
110 Degree FOV, MLX90640 (Qwiic)
-
It's time to say hip hip array for this IR Breakout! The MLX90640 SparkFun IR Array Breakout is equipped with a 32x24 array of thermopile sensors creating, in essence, a low resolution thermal imaging camera. With this breakout you can detect surface temperatures from many feet away with an accuracy of ±1.5°C (best case). To make it even easier to get your low-resolution infrared image, all communication is enacted exclusively via I2C, utilizing our handy Qwiic system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
Product
Solar Simulator
PEC-L15
-
●Light source/lamp house integrated compact design●Irradiation head rotates (downward, upward, sideways irradiation possible)●5cm square optical filter can be attached●Equipped with high-speed shutter (100ms)●Body weight is only 16kg.
-
Product
Inline OEM High Resolution Thickness & Resistivity Module for PV / Solar Sorters
MX 152
-
To allow three thickness scans during belt transport at different wafer sizes, two measuring bars, one from top and one from bottom, hold 3 sensors each.
-
Product
Full Performance and Flexibility on ECIS 8 Well Arrays
Sciospec ECIS Adapter
-
The ECIS CULTUREWARE 8 well arrays are a very common choice for a broad range of impedance-based cell experiments like cell groth, cell migration, wounding/healing, barrier function, tox-screening, adhesion and proliferation studies. With the Sciospec ECISadapter you can bring your ECIS experiments to the next level: more speed, higher resolution, more possibilities. Harness the full power of Sciospec impedance analyzers on your existing ECIS arrays. The ECISadapter just plugs into compatible Sciospec impedance analyzers like the ISX-3 and you´re good to go.
-
Product
Solar Cells and Modules Online Measurement System
PV-LIT
-
The fully automatic PV-LIT testing system offers individual and serial testing options for solar cells and complete solar modules. The modular testing system allows easy integration into existing production lines and can be used in automated serial testing for quality assurance.
-
Product
Compact Linear Line Array Loudspeaker
LEOPARD
-
Say hello to LEOPARD, the most lightweight, versatile line array in its class. The best-selling loudspeaker in the LEO Family faithfully reproduces sound with unsurpassed depth and clarity in a broad scope of installed and touring applications. In Meyer Sound tradition, LEOPARD delivers exceptional phase coherence, consistent coverage, extremely low distortion, and unrivaled power-to-size performance.
-
Product
Single LED Arrays | Red | 2 Or 10 MA
LED-S-r-2/10
-
Pre-mounted single LED, high luminosity with low power consumption and adapt to DIN41494
-
Product
Anti-Sulfurated Chip Resistor Array
-
Panasonic Industrial Devices Sales Company of America
An AEC-Q200 Compliant SeriesPanasonic components specified as AEC-Q200 Compliant are consistently designed into automotive systems. However, today’s Design Engineers are specifying AEC-Q200 components to meet the high-quality standards of devices beyond automotive applications.
-
Product
Solar Module Tester
REOO GIV-20A2616
-
REOO GIV-20A2616 Solar Module Tester is designed for PV module manufacturing inspection, enabling fast module performance inspection and stable production quality verification. Built for solar factories, it supports reliable module testing decisions.
