Limiters
-
Product
Repeat Durability Tester
TIQ1000
-
It is a device to measure repeated endurance such as limit bending test of board, endurance test of mounted board, endurance test of connector, etc. Continuity data and load data can be obtained during the cyclic endurance test. Conforms to JEITA ET-7407 "Environmental and durability test methods for mounted CSP/BGA packages".
-
Product
Thermalyze Extension for Steady State Analysis
Lock-In
-
Steady-state thermography is limited to detecting hot spots that heat up a minimum of 100 mK (0.100°C). This may be useful for locating shorts on high-power devices, but is inadequate for detecting low power defects such as semiconductor device leakage current or short circuit with very low or very high resistance. Steady-state thermography also suffers from poor spatial resolution as the heat from localized hot spots diffuses rapidly, blurring the location of the heat source.
-
Product
Vehicle Tracking System
-
Information System Technologies Inc.
ISTI has built a vehicle tracking system that overcomes the challenges with acoustic tracking and localization of small ground and airborne vehicles using low-cost wireless sensor nodes. The sensor-level sub-band feature extraction and streaming of the encoded data enables real-time direction of arrival (DoA) estimation and tracking even for large wireless sensor networks with limited bandwidth. Benefits include: accurate tracking of single or multiple closely spaced electric or gas driven small planes and UAVs, collaborative decision-making, target localization and classification, robustness to sensor node loss, flexibility and deployment ease. The interface gives users complete control over the entire sensor network, including the ability to monitor the azimuth and elevation angles to the targets in real-time.
-
Product
Test Valva Score
AI
-
Test Value Score is a revolutionary AI-powered feature that dynamically assigns a score to each test according to the contribution it provides to the testing process. The Test Value Score allows Test Managers to optimize their testing operation under time constraints and budget limitations.
-
Product
Magnetic Field and Permeability Measurement
MAGNETOSCOP® 1.070
-
Foerster Instruments, Incorporated
The MAGNETOSCOP 1.070 is a portable magnetometer system with microprocessor and probes for measuring the magnetic flux density as an absolute or differential value (gradient). It has a USB port for simple data transfer and an SD card for saving measurement data and parameters. The measuring system also facilitates the recognition and saving of peak values and the adjustment of thresholds for limit values. The unit can be used for series and individual measurements. The data can be easily analyzed and documented with the PC software included in the scope of delivery. The MAGNETOSCOP 1.070 thus facilitates the portable and fast measurement of the relative permeability within the scope of the quality control of stainless steel and low-permeable (non-magnetic) alloys as well as the localization of ferrite enclosures. Changes in material (sulfidation, degradation of lamination, structural changes) can also be proven thanks to permeability comparative measurements.
-
Product
Switcher
1154B
-
The 1154B is a completely redesigned 4-input, 1-output AutoSelecting switcher with infrared remote control. It switches high definition component video up to 1080p, and audio signals including stereo (analog), digital coaxial, and digital optical audio. The 1154B is a useful companion to any component video-based entertainment system, enabling higher performance video switching than most A/V receivers, and a step up in quality over passive switchers with limited bandwidth.
-
Product
Single Head Component Testers
34XX
-
Performs DC, AC, and pulsed tests. Excels at evaluating difficult to measure parameters on zeners, current limiters, varactor tuning diodes, darlingtons and matched dual transistors. 24 bin opto-isolated handler/prober interface. Parallel first-in first out computer to tester interface for maximum throughput. Parallel testing with a 3402E or 3403E allows shared test execution for extremely high throughput applications when interfaced to high speed handlers with multiple test sites.
-
Product
FFT Analyzer Software Modules
-
Metra Meß- und Frequenztechnik Radebeul GmbH & Co. KG
*Vibration analyzer for low and middle frequencies*Calculates the spectrum of vibration acceleration*VM-FFT+ also for velocity and displacement*RMS and peak spectrum*Envelope spectrum for roller bearing analysis with VM-FFT+*Limit curve with external alarms in VM-FFT+*Power spectral density (PSD) with VM-FFT+*Two measuring cursors for magnitudes and frequencies with snap-in function*Up to four signals per window*One VM-FFT license can be operated simultaneously up to four times with different settings*VM-SCOPE may trigger the frequency analyzer module VM-FFT*External messengers *Offline measurement
-
Product
7" WVGA, 64MB, 128MB(NAND), Serial X3, Ethernet
WOP-207K
-
ARM9™ 32-bit RISC processor with 64 MB SDRAM working memorySupports over 500+ PLC industrial communication protocolsBackup memory 128KB for retaining critical data or parameterSupports the HMINavi Designer development tool free on Windows 10Supports HMINavi Runtime data downloads through Serial, Ethernet, USB portNo limitation on the internal I/Os points used for variety applicationEasy to switch one application to different LCD sizes in secondsSupports operation in both landscape and portrait modePanel mount design ensures easy installation and IP66-rated front panel
-
Product
47~1200MHz FTTH CATV Optic Receiver
H1228
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai H1228, the operating bandwidth of 47~ 1200MHz, is a low power, high performance, cost-effective triple play, FTTH CATV optical receiver, Whether used in analog television or digital television. Products with high sensitivity optical receiver tube and Huatai special low noise matching circuit. Receiving at high optical power can be adjusted by PAD level, played limiting output, so H1228 within a large dynamic range of the received optical power of +2 dBm ~-21dBm, have excellent characteristics.
-
Product
Schottky Barrier Bridge Quads
-
SemiGen’s Silicon Schottky Diodes are designed for applications through 40Ghz. The special process technology utilizes various metal schemes to provide excellent performance of Low, Medium, and High Barrier applications. The end result is a low resistance diode with tightly controlled capacitance which allows for optimum performance. Low conversation loss and superior TSS make these diodes ideal for detector / mixer applications with frequency ranges from S band to Ka band as well as modulators, lower power limiters and high speed switches.
-
Product
Explosion Proof Area Hydrogen Monitor
HY-ALERTA™ 2620
-
H2scan’s 2620 Explosion Proof Area Hydrogen Monitor provides hydrogen-specific leak detection and measurement for hydrogen concentrations as low as 4000 ppm and can be scaled to any concentration up to 5% hydrogen by volume, a range representing 10% to 125% of hydrogen’s low flammability limit. The monitor is designed for either ceiling or wall mount. H2scan’s hydrogen-specific sensor technology has no cross sensitivity to other combustible gases, thus eliminating false positive alarms and ensuring safety system reliability.
-
Product
Programmable Industrial USB 3.0 Hub (8 Ports)
-
The USBHub3+, an 8-port programmable USB 3.0 Hub. Designed by engineers for engineers - connect the USBHub3+ with confidence to expensive lab or production equipment. Enable/Disable any Downstream Port. Maintain selectable control of data, SS lines, power lines for any port. Monitor Voltage and Current on any/all ports. Supply up to 2.5A per port. Set Current Limits on any port. Select between two (2) Host Connections.
-
Product
Clean Room Torque Screwdrivers
-
With the growing trend of clean room manufacturing, the need for torque tools that meet stringent cleanliness requirements has increased. Responding to this manufacturing need, Mountz offers clean room torque screwdrivers. Clean Room screwdriver is a preset torque limiting screwdriver (internally adjustable). The cam-over design prevents overtorquing for your application.
-
Product
Inductively Coupled Plasma Spectroscopy (ICP-OES/MS), ICP Analysis Services
-
ICP-OES measures the light emitted at element-specific characteristic wavelengths from thermally excited analyte ions . This light emitted is separated and measured in a spectrometer, yielding an intensity measurement that can be converted to an elemental concentration by comparison with calibration standards. ICP-MS (ICP-Mass Spec) measures the masses of the element ions generated by the high temperature argon plasma. The ions created in the plasma are separated by their mass to charge ratios, enabling the identifcation and quantitation of unknown materials. ICP-MS offers extremely high sensitivity (i.e. low detection limits) for a wide range of elements
-
Product
Transmitter (Export Only)
SMB
-
The input section features the unique servo bias input circuitry with a standard TA5M type jack for use with electret lavaliere mics, dynamic mics, or line level signals. A DSP-controlled analog audio limiter is employed before the A-D converter. The limiter has a range of more than 30 dB for excellent overload protection and a dual release envelope that makes the limiter acoustically transparent while maintaining low distortion. The limiter recovers quickly from brief transients, with no audible side effects, and also recovers slowly from sustained high levels to keep audio distortion low while preserving short term dynamics.
-
Product
Microwave Components
-
We are a worldwide leader in the design, development and manufacture of radio-frequency and microwave components, and our product portfolio is one of the most comprehensive anywhere in the world.Our magnetrons, performance monitors, low noise front ends, circulators, loads, limiters and receiver protectors are trusted to power every type of commercial radar application, including airborne, navigation and guidance devices, radar and sonar equipment and electronic surveillance systems.
-
Product
3U CPCI To PCI 4 Slot Adapter
-
The PCI-Adapter is a carrier board, allowing the operation of any standard (desktop) PCI card in a CompactPCI® system. The PCI-Adapter acts as a PCI bridge, providing an electrically and mechanically optimized interface between PCI and CompactPCI® system. Our adapters include a PCI Bridge. Some competitor products do not provide a PCI bridge, thus reducing adapter costs by tolerating a violation of the PCI specs. Overall PCI compatibility however is a must in order to achieve total system reliability. Please bear these facts in mind, when comparing prices of PCI-Adapters. All modern operating systems can treat a PCI bridge in a plug and play manner meaning that the bridge remains virtually transparent, as if the PCI component(s) behind the bridge on the secondary PCI bus were part of the primary PCI bus. Using the PCI-Adapter/bridge allows standard PCI boards to work in a CompactPCI® system is both a reliable technical solution, and a smart economical decision. The PCI-Adapter frees the system integrator from the need of a redesign of PCI cards already available to the CompactPCI® standard. This is a great advantage, especially when time to market is critical, or the number of systems to be built is limited, or the function to be implemented has fast innovation cycles.
-
Product
Ultrasonic Thickness Gauge
MMX-6
-
The MMX-6 is a simple to use hand-held Ultrasonic Thickness Gauge with the ability to measure through paint and coatings and eliminate the thickness of the paint or coating. The MMX-6 uses a dual element style transducer. With the single press of a button, the MMX-6 can be switched between pit or flaw mode ( pulse-echo), and through paint/coatings mode (echo-echo) for maximum inspection efficiency. The MMX-6 is equipped with a bundle of features to make your job easier: Alarm mode, high speed scanning, and data send are the main features of the MMX-6. The MMX-6 comes as a complete kit, ready to use, and is backed by Dakota Ultrasonics 5 year limited warranty.
-
Product
Vector Network Analyzer
SNA5000A
-
The SIGLENT SNA5000A series of Vector Network Analyzers have a frequency range of 9 kHz to 8.5 GHz, with 2 and 4 port models available. Designed to give you instant insight into scattering, differential, and time-domain measurements. They are effective instrumentation for determining the Q-factor, bandwidth, and insertion loss filters and feature impedance conversion, movement of measurement plane, limit testing, ripple test, fixture simulation, and adapter removal/insertion adjustments. There are five sweep types: Linear-Frequency, Log-Frequency, Power-Sweep, CW-Time, and Segment-Sweep mode. The SNA5000A series VNAs also support scattering-parameter correction of SOLT, SOLR, TRL, Response, and Enhanced Response for increased flexibility in R&D and manufacturing applications.
-
Product
Multi-Component Gas Analyzer
VA-5000 / VA-5000WM Series
-
The Multi-Component Gas Analyzer VA-5000 Series is an all-round analyzer that satisfies measurement needs as required for environmental monitoring, energy development support, quality controls, and continuous emission monitoring, etc. The VA-5000 Analyzer can be configured with up to 4 detector modules within a single case. Many combinations of detector modules with a wide selection of ranges allows this series of analyzers to be used for a variety of applications. The VS-5000 Sample Gas Conditioning Systems are designed to support the VA-5000 Analyzers by proving the optimal sample conditions for measurement. We also have wall mounted type analyzer (VA-5000WM) that enables to install in a limitted installation space.
-
Product
Multi-Band Imaging
-
Bodkin Design & Engineering, llc
A multi-band camera provides high-resolution, co-registered visible and infrared imagery through a common aperture telescope, unlike conventional visible or infrared cameras that provide image data in limited wavelength bands. Bodkin Design has created the Omnispotter multi spectral camera to enable the user to better discriminate targets from both background and decoys by blending color images with information from the IR band. The images obtained from this system penetrate darkness, camouflage, smoke and clutter better then either visible or IR images could alone.
-
Product
Handheld Digital Multimeter, AC/DC Voltage, Continuity, Diode, 3.5, 2000, Manual, 250 V
72-13440
-
*Palm size digital multimeter with 2000 count clear LCD display*CAT II 250V environment safety rating*Manual functional select and manual range selection*2m drop test, precision protection*Auto backlight off*Knobs shift smoothly, in-line with ergonomics*Equipped with comfortable protective cover and test probe holder*Powered by AAA 1.5V x 2 batteries*Non-contact voltage (NCV) detection*12-month limited warranty *view Terms & Conditions for details
-
Product
ATCA CO6 DC 6 Slot 5U
-
The AdvancedTCA® CO6, 6-slot chassis, DC version is dedicated for applications where available space is limited.
-
Product
Single-Phase Static Switches
ISSF "PLUS"
-
The solid state switches ISSF “PLUS" exceed the limitations of electromechanical switches for many difficult and demanding applications, such as the control of high power motors, transformers, tungsten lamps, heating elements, electric furnaces, etc.
-
Product
12:1 IR Thermometer w/ K-Type Thermocouple Input
INF195C
-
UEi Test & Measurement Instruments
The INF195C offers the unique circular laser targeting showing users the exact spot being measured. This 12:1 Infrared Thermometer also offers advanced features including a wider temperature range, K-Type input, selectable emissivity levels, Min/Max, average, differential, a user adjustable alarm and backed by a 1-Year limited warranty.
-
Product
PXI High Density MUX BRIC, 48-Chan, 10-Pole
40-570-413
-
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
Digital Multimeter
HMC8012
-
True RMS measurement, AC, AC + DC Simultaneous display of three measurement functions, e.g. DC + AC + statistics Measurement functions: DCV, DCI, ACV, ACI, frequency, resistance (2- and 4-wire), temperature, capacitance, diode and continuity test Mathematic functions: limit testing, minimum, maximum, average, offset, DC power, calculation of dB and dBm Data logging to internal memory or USB stick
-
Product
Compact Modular Industrial Computers Based On 14/13/12 Gen Intel® Core™ Processors
MVP-5200 Series
-
The MVP-5200 Compact Modular Industrial Computers powered by 14/13/12th Gen Intel® Core™ i9/i7/i5/i3 and Celeron processors. Featuring Intel R680E chipset and supporting up to 65W, the computers can also incorporate GPU cards in a rugged package suitable for AI inferencing at the Edge, and can be used for but not limited to smart manufacturing, semiconductor equipment, and warehouse applications.
-
Product
Serial to Ethernet Connector
-
With Serial to Ethernet Connector you can share up to 255 serial devices over network turning your computer into a terminal server. With this serial over network solution any device connected to a COM port can be accessed and used from any spot on the globe as if it were physically connected to the local machine. The data sent by serial port device is transmitted over a TCP/IP network. This is achieved thanks to our virtual serial port technology that emulates standard COM ports behavior and Windows OS treats the virtual ports as the real ones. Although the ports are treated as physical you are not limited to the quantity of physical COM ports and can create COM port connections without occupying real serial ports. With Serial to Ethernet Connector you can: share serial port for incoming connections, connect the port to remote host, or share port using UDP connection. Starting from version 7.0 Serial to Ethernet Connector got absolutely new user interface for even easier creation and management of connections with latter conveniently visualized and more.
