Deep Packet Inspection
check to examine data within a packet. Also known as: DPI
-
Product
Automated Optical Inspection System
AV880 Series
-
The AV880 Series of AOI solutions from ASC International provides the same high level inspection capabilities as found in our AV862/AV871 Series of AOI systems all wrapped into an inline platform for continuous flow requirements. A price to performance ratio sure to please those looking for a quick ROI.
-
Product
Fiber Inspection and Cleaning
-
Dust - just because you can't see it doesn't mean it's not there. A 1-micrometer dust particle on a single-mode core can block up to 1% of the light (a 0.05dB loss). The only way to know it's clean is to inspect it before you connect it. And if it's dirty, it needs to be cleaned with the right tools or you might just make it worse. Know it's clean with our cleaning and inspection tools.
-
Product
Fixture and Software for Open/Leak Inspection
-
In addition to jigs and fixtures for probing conductors and electrode pads, NIDEC-READ provides specialized software for test point selection and log analysis.
-
Product
Conformal Coating Inspection
-
Conformal coating plays a key role especially when electronic assemblies are used in products and systems that perform safety-relevant tasks. The coatings applied to the circuit board protect against environmental influences such as dirt, dust, moisture, condensation, and varying temperatures. Increasing packing densities and the trend toward miniaturization are also making conformal coatings essential. The insulating effect of the coating allows reductions in the distance between conductor paths while also boosting the performance of terminal devices.
-
Product
(AOI) Automated Optical Inspection Systems
-
For automated defect detection and high-accuracy measurements. VisionGauge Online High-Speed AOI systems are perfect solutions for demanding high-throughput, high-resolution applications. These systems are perfect for a wide range of applications including MicroElectroMechanical systems (for MEMS inspection or MEMS measurement), semiconductor & discrete device inspection and measurement.
-
Product
Property Inspection Solution
DJI / IMGING
-
Advanced DJI drone solutions for the P&C Insurance industry. IMGING™ to conduct full roof and property inspections with incredible detail in as little as ten minutes from start to finish, and they’re getting high-resolution, actionable data they can use to make informed decisions. By combining Insurance-focused workflows and patents-pending autonomous flight control technology, IMGING is making roof inspections safer, quicker, and more consistent. It’s deceptively simple, amazingly powerful, and built specifically for Insurance.
-
Product
Printed Circuit Board Inspection System
-
NIDEC-READ offers an array of testing equipment used to conduct open/leak tests on motherboards, as well as many other printed circuit boards. They can be flexibly configured according to applications in terms of size, type, and the number of test pins required.
-
Product
BACnet Packet Capture And Protocol Analyzer For MS/TP
BACTrace
-
The multi-pane user interface shows captured packets in several different kinds of detail. The upper pane displays a quick summary of received packets, each of which is identified by number. The MS/TP frame type, destination and source MAC addresses are shown, as well as a timestamp in milliseconds. For APDUs, the BACnet service is also shown.
-
Product
Wafer & Die Inspection
-
SemiProbe wafer inspection system (WIS) examines, locates and identifies defects created during wafer manufacturing, probing, bumping, dicing or general handling. This provides microelectronic device manufacturers with accurate, timely quality assurance and process information. The WIS has single sided and double sided wafer mapping capabilities and can improve efficiency, reduce manufacturing costs, increase yields and shorten time to market.
-
Product
Digital Inspection Probes
DI-1000
-
The ergonomically designed DI-1000 is Lightel’s all digital video microscope probe. It connects directly to your PC through the computer’s USB2.0 port. Featuring easy single finger focusing, a built-in image freeze/capture button, and detectable resolution to 0.5µm, the DI-1000 package includes our free ConnectorViewTM (standard) software, providing digital zoom, image display, image capture, auto-calibration and basic analysis tools.
-
Product
Industrial CT X-Ray Inspection System
X7000
-
The X7000 is North Star Imaging’s largest standard system. The large scanning envelope and generous focal distance allow for unparalleled inspection capabilities of very large objects. The system is great for composites, castings, pipes, tubes, welds and similar parts.
-
Product
Inline Wafer Electrical quality Inspection
ILS-W2
-
the Ultimate Wafer Electrical Quality Inspection Unit for Wafer Inspection Systems
-
Product
Automotive Inspection Kit
-
Produced specifically for the automotive aftermarket and Insurance Assessors, 3rd party consultants, body shops and used car sales, these kits provide an instant measure of the coating thickness of panels.An illuminated magnifier is supplied to enable close inspection of bodywork.Measurement parameters include:Surface temperatureSurface inspectionCoating thickness
-
Product
X-Ray Inspection System
MXI Quadra 5
-
Quadra™ 5 is the X-ray inspection system of choice for sub micron applications such as PCB and semiconductor package inspection, counterfeit component screening and finished goods quality control.
-
Product
Fiber Inspection Probe
FIP-920
-
FIP-920 Fiber Optic Inspection Probe combines a 3.5” high definition TFT LCD display, provides a detailed image of fiber end-face, zoom in/out feature make it easy to identify the smallest particles, scratches. With the attached SD card memory, you can capture/record the live end-face image, the image file can be reviewed/transferred via SD card reader or USB cable. Up to 8hrs battery working make it possible to inspect the fiber end-face at any time and any place.
-
Product
DFM (Deep and Fast Modulated) generators up to 280 GHz
-
Insight Product Company offers DFM (Deep and Fast Modulated) mm-wave sources at frequencies from 30 to 280 GHz. DFM generators are designed to go swiftly from the generation to the non-generation mode and back. This process controlled by the external TTL signal. ON/OFF switch time is approximately 2 nanoseconds.
-
Product
Deep Submersible Particle Size Analyzer
LISST-Deep
-
The LISST-DEEP instrument obtains in-situmeasurements of particle size distribution,optical transmission, and the opticalvolume scattering function (VSF). Using ared 670nm diode laser and a customsilicon detector, small-angle scatteringfrom suspended particles is sensed at 32specific log-spaced angle ranges. Thismeasurement is post-processed to obtainsediment size distribution, volumeconcentration, optical transmission, andVSF. The electronics and opticalconfiguration in the LISST-DEEP are verysimilar to Sequoia’s workhorse, the LISST-100X. However, because of the extremedifficulty associated with keepingalignment under high pressure, the LISSTDEEPhardware design is radically differentfrom the LISST-100X. This allows theLISST-DEEP to be deployed down to 3000m and obtain reliable measurements ofthe in situ particle size distribution andvolume concentration in waters withoptical transmission up to 98.5%.
-
Product
X5 Pack X-Ray Inspection
-
Designed to be integrated into line with built-in automatic reject and available in 300, 500 and 600 mm belt width models, the X5 Pack is perfect for a variety of unpackaged and packaged products.
-
Product
X-Ray Inspection System
MX1
-
Manncorp’s new MX1 is a high-performance x-ray inspection system designed for real time imaging of multilayer PCBs and dense metal BGAs, μBGAs, and chip scale packages. Its high voltage (80kV), computer-controlled x-ray tube and 35 μm focal spot provide the power necessary for detection of a variety of defects including bridging, voids, and missing balls. The MX1’s standard camera features continuous zoom magnification from 4X to 50X and variable angle viewing up to 45°, and an upgrade to the x-ray tube can boost magnification to 225X.
-
Product
Digital Inspection Camera
MaxiVIDEO MV108S
-
It turns your Autel tablet into a video inspection scope, allowing you to examine difficult-to-reach areas hidden from sight. It is capable of recording digital still images and videos. Includes mirror, hook and magnet attachments.
-
Product
Electronic Inspection Systems
-
Intego's knowhow even makes it possible to identify challenging defects that may be located under the surface. One system is the inspection of chips by means of lock-in thermography, which visually represents the IR radiation intensity signal of electronics. Special lasers and flash lamps generate a very short heat impulse (10 ms) on the chip, which generates a measurable heat flow. In most cases, a resolution of < 1 μm can be achieved.
-
Product
Deep Ultraviolet Observation System for Microscope
U-UVF248
-
Model Capable of High-magnification/High-contrast Deep Ultraviolet (DUV) Observation. A Semiconductor / FPD Inspection Microscopes.
-
Product
Thickness and Flaw Inspection
MultiScan MS5800
-
Eddy current testing is a noncontact method used to inspect nonferromagnetic tubing. This technique is suitable for detecting and sizing metal discontinuities such as corrosion, erosion, wear, pitting, baffle cuts, wall loss, and cracks in nonferrous materials.
-
Product
Inspects MEMS and Wafer Level Devices
NorCom 2020-WL
-
The NorCom 2020-WL is specifically designed for wafer-level inspection and leak tests up to 1000 devices per cycle. The system can inspect up to an 8” wafer on or off a saw frame. It is designed to test MEMS and other wafer level devices that have a cavity.
-
Product
Inspection scope
KI-TK1012
-
Inspection scope & cleaning materials. Interchangeable MPO SC LC connectors
-
Product
Digital Video Inspection Microscope
-
Contamination is the first reason for troubleshooting optical networks. Proactive inspection and cleaning of fibre connectors can prevent poor signal performance, damage to equipment, and network downtime. DIAMOND’s Video Microscope Kit contains all necessary tools for proper inspection and cleaning of the connector’s front-faces to help ensure optimal connector performance.
-
Product
Entry Level GPR System for Concrete Inspection
StructureScan Mini LT
-
Geophysical Survey Systems, Inc.
The StructureScan™ Mini is GSSI’s all-in-one GPR system for concrete inspection. This handheld system locates rebar, conduits, post-tension cables, voids and can be used to determine concrete slab thickness in real-time.
-
Product
Deep Learning Bundle
-
Set of Deep Learning inspection libraries optimized for machine vision applicationsPerforms image classification, supervised or unsupervised segmentation and object localizationIncludes EasyClassify, EasySegment and EasyLocateSimple APIIncludes the free Deep Learning Studio application for dataset creation, training and evaluationSupports data augmentation and masksCompatible with CPU and GPU processing
-
Product
Cleanliness Inspection System / Microscope
CIX90
-
The OLYMPUS CIX90 technical cleanliness inspection system is a dedicated, turnkey solution for manufacturers who maintain high quality standards for the cleanliness of manufactured components. The OLYMPUS CIX90 system makes it easy to quickly acquire, process, and document technical cleanliness inspection data to comply with international standards. The system is intuitively designed to guide users through each step of the process so that even novice inspectors can acquire important cleanliness data quickly and easily.
-
Product
Inspection Systems
-
Video Inspection Systems with?or without measurement capabilities are an excellent way to evaluate and test small items or items in?difficult to access locations. Many options are available in addition to the measurement capability. Video Inspection is used for a variety of purposes including the ability to see? and measure items that are much smaller than the eye can see or that hand tools can measure. Video systems can also reduce the eye and/or back strain associated with production environments where an operator must look in a microscope all day.
