-
Product
Flow Indicator
Qualitrol 092
-
Designed to indicate “pump on” and “pump off” conditions within a forced cooling system. Select models also indicate flow direction. Up to two SPST or SPDT switches are available for control and/or alarm functions. Large dial face provides easy viewing and is magnetically coupled to the flange assembly allowing leak free replacement if damaged.
-
Product
flow Coefficient
-
For the determination of the flow coefficient of fine aggregates up to 4 mm particle size.
-
Product
Gas Flow Meters
-
There are innumerable circumstances where gas flow rates need to be quickly and precisely measured. You’ll always be prepared with Netech’s versatile range of gas flow meters, which are designed to measure several types of gases including air, N2, O2, CO2, and He.
-
Product
Flow Cytometry
-
The iQue® Advanced Flow Cytometer allows researchers to acquire and analyze high content, multiplexed assays needed to assess immune cell function by combining cell immuno-phenotyping, cell health, and secreted protein (cytokine) analysis in every well of a microtiter plate. Accelerate your research by resolving complex cellular research questions via multiplexed analysis in a single well.
-
Product
Fast Response Flow Controller for Low Flow
HFM-300 / HFC-302
-
The all metal HFM-300/HFC-302 is Teledyne Hastings' metal sealed, fast response series of mass flow meters and controllers. Featuring reliability and stability, the 300 Series is chosen by OEM's for its fast response under a wide range of conditions.The HFM-300 / HFC-302 meters and controllers have flow ranges from 0-5 sccm to flows of 0-25 slm; provide analog outputs, are constructed of stainless steel and have normally closed valves. The full scale range is specified by the end user. A NIST traceable calibration certificate is standard. Corrosive gases and pressures up to 1000 psig are easily measured. Cleaning for oxygen service is available.
-
Product
Micro Flow Sensor
2000
-
The Signet 2000 Micro Flow Sensor is constructed from Polyphenylene Sulfide (PPS), which provides high material strength. The 2000 MicroFlow Sensor offers two flow ranges starting at 0.11 or 1.13 lpm (0.03 or 0.3 gpm), for clean process liquids, regardless of fluid color or opacity.
-
Product
Flow Ratio Controllers
-
Optimizing process performance just became easier with the DELTA™ Flow Ratio Controller (FRC). Widely used in a variety of flow splitting applications such as etching, stripping, and PECVD, the DELTA™ Flow Ratio Controller (FRC) provides users with the ability to distribute gas or gas mixtures to different zones in a process chamber.
-
Product
Mass Flow Meters
-
Alicat Scientific, Incorporated
Use mass flow meters to measure gas flow from 0.5 SCCM to 10,000 SLPM, with accuracies as good as ±0.5% of reading or ±0.05% of full scale and a measurement range of 0.01-100% (10,000:1 turndown).
-
Product
Fast Response Flow Controller for Medium Flow
HFM-301 / HFC-303
-
The HFM-301 / HFC-303 meters and controllers have flow ranges from 0-25 slm to flows of 0-1000 slm; provide analog outputs, are constructed of stainless steel and have normally closed valves. The full scale range is specified by the end user. A NIST traceable calibration certificate is standard. With a choice of elastomers and high pressure options, the HFM-301 / HFC-303 services a wide variety of applications. Cleaning for oxygen service is available.
-
Product
Turbine Flow Meters
-
Turbine flow meters are the most popular choice to measure flow electronically. They offer a wide flow and application rangeability. Turbine Flow Meters are easy to maintain, durable and versatile.
-
Product
Heat Flow Meter
-
Thermal conductivity is a measurement of a materials ability to conduct heat and can be critical for evaluating energy efficiency and thermal performance of materials. The HFM-100 Heat Flow Meter is designed as an easy-to-use method for the measurement of thermal conductivity and thermal resistance of insulation products, construction materials, packaging, and assemblies. Available at an exceptional value, the Thermtest HFM has been engineered for industry-leading performance by combining the highest accuracy, repeatability, and widest temperature range possible, and follows international standards: ASTM C518, ISO 8301, and EN 12667.
-
Product
Heat Flow Meters
Fox Series
-
Fox Series Heat Flow Meters are reliable, easy-to-use, and durable thermal conductivity measurement instruments. Each of our FOX heat flow meters combines advanced technology with over 20 years of superior engineering. Explore our lineup of thermal conductivity instruments.
-
Product
Mass Flow Meters
-
Omega's Mass Flow Meters are available with control functions, and come with or without display, flow totalizers, and alarms. Coriolis Meters are available for custody transfer applications.
-
Product
Mass Flow Controller
SEC-E Series
-
This general purpose mass flow controller has a reliable thermal sensor and solenoid valve, allowing you to achieve high-level control of gas flow. A versatile component, the mass flow controller sec-e series can be used in a wide range of industries.Gas flow through the mass flow controller can be controlled over a range of flows: from 10 SCCM to 200 SLM.
-
Product
DIN Viscosity Flow Cups
2350
-
The Elcometer 2350 DIN Viscosity Flow Cups are very easy to use instruments made of anodized aluminium with a stainless steel orifice, for measuring the consistency of paints, varnishes and similar products.
-
Product
AC Fuel Flow Signal Generator
TA-100
-
The TA-100 signal generator was designed to facilitate testing of aircraft fuel flow indicators that require two input signals designated as “Drum” and “Impeller”. This generator provides both signals so as to provide a direct interface to the fuel flow indicator under test. The generator also provides switched power out to the unit under test as well as a 5v source for testing the bezel lighting. The original design was built around the requirements for the AMETEK series indicators (pn: 10171 series). This generator simulates a reference and a time delayed signal of appropriate amplitude for an indication of up to 1200pph for the indicator under test. The “PPH Select” switch provides fixed signal delays representing 0, 200, 400, 800, 1000 and 1200pph flow rates respectively, this provides the mechanic with an expedient check of the indicators accuracy. The “PPH Adjust” control allows the mechanic to vary the signal delay throughout the full range and serves as a good method for checking of pointer smoothness from stop to stop. The unit’s front panel also provides test jacks to monitor the “FDR Output” as well as the drum and impeller signals. The TA-100 requires only 28Vdc to operate. This generator provides a very economical approach to any repair facility or flight department as it becomes an alternative to purchasing two bench top signal generators. The TA-100 generator at the very least can provide a simple functional test and eliminate the high cost of exchanging an indicator as a function of troubleshooting the aircraft system.
-
Product
Mass Flow Test Systems
-
No matter the industry, product integrity is necessary to the manufacturing process. Everything leaks, and mass flow testing provides a fast, reliable determination of leakage to ensure it is within permissible ranges.
-
Product
Flow Controllers
Concert™ Series
-
Concert flow controllers enable real-time flow monitoring and control when used with Nordson TruFlow™ devices – meters, dividers or applicators. This variation management capability helps improve material delivery and dispensing so manufacturers reduce waste, improve product quality and enhance production efficiency.
-
Product
Air Flow Measurement
-
Transcat is your premier provider of air flow measurement. We carry an extensive inventory of test & measurement equipment, with over 3000 products available for same-day shipping. For many instruments, new instrument calibration is also available, ensuring that your product is tested and ready for use as soon as you get it.
-
Product
Capacitive Electromagnetic Flow Sensor
WFC
-
This is a flow sensor with a through structure.No foreign matter is clogged or detection failure occurs. Ideal for spot welding machines, various machine tools, induction hardening equipment, etc.
-
Product
Paddle Wheel Flow Sensor
FSP
-
FSP - Paddle Wheel Flow Sensor, Using SUS and corrosion-resistant materials and design oxidation resistance, good stability and high resolution built-magnet rotor, NPN pulse square wave can be connected directly to the PLC / IPC IPC, the product is easy to maintain, easy to operate.
-
Product
Flow Meters
900 Series
-
The Blancett Series 900 flow meters are rugged, low-priced and specifically designed to measure floodwater line flow in secondary oil recovery operations. Using time-proven rotary vane and multi-jet impeller mechanisms, the Series 900 flow meters will provide reliable long-term measurement and totalization with minimum attention and maintenance.
-
Product
Propeller Flow Meters
-
Whatever the need, McCrometer propeller meters offer unbeatable value in cost of installation and ownership and set the standard for ease-of-use, reliability and economy. Our leading-edge meters offer versatile water flow measurement for more than 65 years.
-
Product
Mass Flow Calibration
-
Allow instrument interchangeability without affecting your process and meet ISO 9001 requirements easily and efficiently with Process Instruments’ Mass Flow Calibration and Repair Services.
-
Product
Variable Area Flow Meters
-
Omega's extensive portfolio of variable area flow meters supports any industrial, medical, lab, or process control application. Let Omega help you select the proper flow meter for your application
-
Product
Turbine Flow Meters
CT300, CT400
-
Flows up to 400 lpm (100 US gpm)Pressure up to 420 bar (6000 psi)Choice of 4-20mA and 0-5V outputs2-3 top ports as std for temperature / pressureBSP or SAE inlet / output portsFor use with oils, fuels, phosphate-estersBi-directional
-
Product
Flow Rate Monitor
Ultraflow 150
-
State-of-the-art signal processing and innovative modularity offers customers incomparable performance, accuracy, flexibility and the most maintenance-free solution amongst all flow technologies.
-
Product
Lake Paddle Wheel Flow Meters
-
Operating much like a turbine flow meter, the paddle wheel flow meter consists of a freely rotating wheel which is outfitted with magnets on the blades or “paddles” of the wheel. As the fluid flows through the meter, spinning the wheel, sensors detect the magnets with each pass.
-
Product
Melt Flow Index Testers
-
Instron® melt flow testers are specifically designed for easy and accurate measuring of Melt Flow Rate (MFR) and Melt Volume Rate (MVR). Our extrusion plastometers range from manual to semi-automated plastic melt flow index testers performing multiple weight tests. All our Melt Flow Index testing equipment meets the latest ASTM and ISO standards.
-
Product
Turbine Flow Meters
CT60, CT150
-
Flows up to 150 lpm (40 US gpm)Pressure up to 420 bar (6000 psi)Choice of 4-20mA and 0-5V outputs2-3 top ports as std for temperature / pressureBSP or SAE inlet / output portsFor use with oils, fuels, phosphate-estersBi-directional
