Headers
-
Product
200 MS/sec RF/IF Rugged Rackmount Recorder
Talon RTR 2746
-
- Operates under conditions of shock and vibration- 4U 19 inch industrial rugged rackmount PC server chassis- Windows® workstation with Intel® processor- 200 MHz max. 16-bit A/D sampling and recording - up to eight channels- 80 MHz recording/playback signal bandwidths- Capable of record/playback of IF frequencies up to 700 MHz- Real-time aggregate recording rates of up to 3.2 GB/sec- Removable SSD drives- Up to 243 terabytes of storage to NTFS RAID disk array- RAID levels 0, 1, 5, 6, 10 and 50- SystemFlow® GUI with signal viewer analysis tool- C-callable API for integration of recorder into application- File headers include time stamping and recording parameters- DDC decimation and DUC interpolation range from 2 to 65,536- Optional GPS time and position stamping- See Datasheet for configuration options for playback, recording and storage capacity
-
Product
Arduino CAN Shield
IFB-10003-INP
-
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
Product
CableEye® HV-Rated QuickMount™ Housing for CAMI Connector Boards
CBH2
-
CAMI Research Inc. (Acton, MA) has released a High-Voltage (HV)-rated QuickMount housing (CBH2) for its CableEye® automation-ready, cable and wire harness testing systems. As a free-standing, quick-release board fixture, it allows users to connect CAMI’s test interface boards to the 64-pin headers of any expansion module - even at some distance. The housing may be used with any CableEye model and is rated to 2100 Vdc / 1500 Vac.
-
Product
Development System
FE-C450
-
* Emulates Dallas Semiconductors DS89C450 * 62K Code Memory * Real-Time Emulation * Frequency up to fmax at 5V * Windows Debugger For C/C++ And Assembler * 44-PLCC Emulation Header * Target Board and Programmer Included * RS-232 or USB Interface * 64K C/ASM and 8K C++ Included
-
Product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Multi Functional VME Logic Module
MDGG-16
-
The MDGG-16 is a single wide 6U VME multi functional FPGA based delay logic and timing module which provides often needed functions as gate generator & pulse generator, logic fan in - fan out, coincidence register and scaler / pre-scaler. The module has 16 LVDS/ECL inputs and 16 ECL outputs on pin headers and 2 NIM inputs as well as 4 NIM outputs (Lemo), which are free configurable in regards to their functionality.
-
Product
Board
Arduino Micro
-
The Micro is a microcontroller board based on the ATmega32U4 (datasheet), developed in conjunction with Adafruit. It has 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs), a 16 MHz crystal oscillator, a micro USB connection, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a micro USB cable to get started. It has a form factor that enables it to be easily placed on a breadboard.
-
Product
Board
Arduino Mega 2560 Rev3
-
The Arduino Mega 2560 is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Mega 2560 board is compatible with most shields designed for the Uno and the former boards Duemilanove or Diecimila.
-
Product
USB Tester 2.0
TLS-0050
-
The USB Tester will make it a snap to monitor voltage levels and current usage without having to re-wire your breadboard. Just connect to your oscilloscope or DMM test leads, and you're good to go! The USB Tester has both banana clip sized drills and standard 0.1" headers. When you are not testing current you can add a jumper for normal operation. The USB D+/D- pins are also broken out so you can monitor those on an oscilloscope, or for USB sniffing.
-
Product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to 4x50-Pin IDC, Male, 2m
40-971B-200-2m-MM
Cable Assembly
This male rear exit to ribbon cable 2m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin male 2.54mm pitch IDC connectors. The 200-pin connector can be secured to the product by male screwlocks. This assembly can be used for applications requiring unterminated cables, simply crop off the ribbon cable headers.
-
Product
Power Interface Board 3U, 2PSU connectors with AC pins
106PIBM302-9001R
-
The PIB 3U 2 slot has two power connector P47 with AC pins and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
Product
Framegrabber
FastXe2
-
The FastXe2 framegrabber series is for users who anticipate a demand for extreme I/O requirements and/or higher bandwidth, complex image processing and real-time high-speed storage in a cost effective platform. The base FastXe, is a one half length raw form factor PCIe (X4) Gen2 board with either six basic 85 MHz Camera Link Channels up to two extended full Camera Link camera interfaces. An auxilliary I/O connector provides a header for adaptation of other high speed interfaces such as GigEx4, high speed analog formats such as UXGA or DVI, or CoaXPress. The front-end data is formatted and preprocessed by a Kintex 7 FPGA before being sent to the PCIe (X4) Gen 2 bus
-
Product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to 4x50-Pin IDC, Male, 0.5m
40-971B-200-0.5m-MM
Cable Assembly
This male rear exit to ribbon cable 0.5m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin male 2.54mm pitch IDC connectors. The 200-pin connector can be secured to the product by male screwlocks. This assembly can be used for applications requiring unterminated cables, simply crop off the ribbon cable headers.
-
Product
Screw-Terminal & Power Adapter Board - DC-coaxial-jack connectivity for 1 or 2 External VDC Power Supplies
TE3202
-
- Provides DC-coaxial-jack connectivity for 1 or 2 external 48 VDC power supplies- Provides screw-terminal connectivity for all sense, return, & output lines- May be directly connected to the HD-DB15 on the TE3200 front panel, or extended with a standard VGA extension cable.- Provided header pins for jumpering sense & return lines to channel output & return lines.- Provides a 2-pin header for jumper configuration with only one externally supplied 48VDC input (but, halves the maximum output current)
-
Product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K0
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Current Transformer Testers
-
Vanguard Instruments Company, Inc.
Performs CT excitation, current-ratio, polarity, and phase angle testsMeasures insulation resistance and winding resistance of the CT seconday windingsMeasures the CT's secondary burdenTest record header information including company, substation name, circuit ID, manufacturer, CT serial number, operator name, and test record-commentsBuilt-in 4.5-inch wide thermal printerPlot Multiple Saturation CurvesStores up to 128 CT test plans and 140 test records internallyUSB, Bluetooth, and USB Flash drive interface
-
Product
S-100 Bus, Vectorbord Plugbord
8804
-
VECTOR Electronics and Technology, Inc.
100 Gold plated edge contacts (50 each side)on 0.125"(3.175mm) centers. Voltage/Ground buses. Zig-Zag buses. I/O mounting area for ribbon cable header. Row and column legends provided. S-100 Form Factor.Pin 1 and 51 committed to power. Pin 50 and 100 committed to ground.
-
Product
Framegrabber
FastX1703
-
The FastX1703 framegrabber series is for users who anticipate a demand for extreme I/O requirements and/or higher bandwidth, complex image processing and real-time high-speed storage in a cost effective platform. The base FastX1703, is a two thirds length raw form factor PCI board six basic 85 MHz Camera Link Channels or an extended Camera Link camera interface. An auxilliary I/O connector provides a header for adaptation of other high speed interfaces such as LVDS or high speed analog formats such as UXGA or DVI. The front-end data is formatted and preprocessed by a FPGA before being sent to the memory subsection, up to four PNX1702 500 MHz processors with 256MB memory each. Finally, the FastX1703 interfaces to the host computer through a 4xPCIe interface for state-of-the-art data acquisition.
-
Product
Header Covers
Series 650
-
Header Covers. Aries offers a complete line of DIP headers and covers useful for mounting components such as resistors, diodes, etc. Consult Data Sheet 12032 for mating DIP header information. Four cover heights provide mounting of 1/8? [3.18] high to 3/4? [19.05] high components.
-
Product
Program Header and Cover
Series 680
-
Program Headers and Covers. Complete versatility for programming within the unit itself...thus eliminating the need for DIP switches in many situations. Available pre-programmed from Aries, or do it yourself using Aries hand tool No. T-680. Consult Data Sheet No. 22002 for programming tool information.
-
Product
SparkFun RGB LED Breakout
WS2812B
-
This is a breakout board for the WS2812B RGB LED. The WS2812B (or "NeoPixel") is actually an RGB LED with a WS2811 built right into the LED! All the necessary pins are broken out to 0.1" spaced headers for easy bread-boarding. Several of these breakouts can even be chained together to form a display or an addressable string.
-
Product
Single row PCB connector
RBA Series
-
Smiths Interconnect's RBA series is a rugged stick header that can be cut to sizes up to 27 positions
-
Product
SparkFun MicroView
USB Programmer
-
The MicroView is the first chip-sized Arduino compatible module that lets you see what your Arduino is thinking using a built-in OLED display. This USB programmer connects directly to the MicroView and lets you not only program the module, but use it to interface with your computer, Rapsberry Pi, or other USB device. The programmer has both male and female headers which allow it to be plugged into a MicroView module and a breadboard at the same time, making prototyping quick and easy.
-
Product
NI TB-2642B Terminal Block for NI 2532B as 1-Wire 16x32 Matrix topology With Column Protection Resistors
782385-06
Terminal Block
The TB-2642B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 1-wire 8x64 matrix. You can directly connect the TB-2642B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2642B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
Product
NI TB-2641B Terminal Block for NI 2532B as 1-Wire 8x64 Matrix topology With Column Protection Resistors
782385-04
Terminal Block
The TB-2641B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 4x128 matrix. You can directly connect the TB-2641B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2641B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
Product
3U PXI Express Board Virtex-5 Medium Speed Quad DAC
SMT759
-
Sundance Multiprocessor Technology Ltd.
The SMT700 module uses a Xilinx Virtex 5 LXT or SXT to implement the interfaces the board provides. The FPGA can be configured either via the onboard flash, or through the Xilinx JTAG header.
-
Product
CB-50 I/O Connector Block with DIN Rail Mounting without cable
776164-90
Terminal Block
50-Pin Male IDA to 50-Pin Female Screw Terminal, DIN Rail, Terminal Block - The CB-50 provides 50 screw terminals for connection to I/O signals from your 50-pin NI data acquisition devices. The CB-50 includes one 50-pin header for direct connection to 50-pin cables. It features a protective plastic base and hardware for mounting on a DIN Rail.
-
Product
NI TB-2640B Terminal Block for NI 2532B as 1-Wire 4x128 Matrix Topology With Column Protection Resistors
782385-02
Terminal Block
The TB-2640B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 1-wire 4x128 matrix. You can directly connect the TB-2640B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2640B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
Product
SparkFun Breadboard Power Supply Stick
3.3V/1.8V
-
This is a very simple board that takes a 4-9V input voltage and outputs a selectable 1.8V or 3.3V regulated voltage. All headers are 0.1" pitch for simple insertion into a breadboard.
-
Product
32 Channel Optically Isolated Digital Card
104-IDIO-16 Family
-
The Model 104-IDIO-16 is a 32-channel PC/104 utility board featuring 16 optically isolated inputs and 16 optically isolated solid state outputs. The isolated, non polarized inputs may be driven by either DC sources of 3-31V (or higher by special order) or AC sources at frequencies of 40Hz to 10KHz. Optically isolating the digital inputs from each other, and from the computer, assures smooth, error-free data transmission in noisy, real-world environments. The 16 input channels are available via a 34-pin IDC type header. The fully protected solid state outputs, capable of sourcing 2A each, are inherently more reliable than electromechanical relays and give system architects a more robust product to design with. The solid state outputs are available via a 50 pin IDC type header.
