Parallel Interfaces
See Also: SCSI, Serial Interfaces
-
Product
PCIe-8433, PCI Express, 2-Port, Isolated, RS485/RS422 Serial Interface Device
781745-01
Serial Interface
The PCIe‑8433/2 is a high-performance industrial interface for high-speed, port‑to‑port isolated communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full‑ and half‑duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
NI-9871, 4-Port, RS485/RS422 C Series Serial Interface Module
779892-02
Serial Interface
The NI‑9871 adds RS485/RS422 serial ports to CompactRIO systems. The serial ports are accessed directly from the FPGA to offer you flexibility in communicating with serial devices. The module has individual buffers on every port that save FPGA space and simplify programming. The NI‑9871 supports standard start bit, stop bit, and handshaking settings. It uses an external power to provide maximum compatibility and reliability under all serial port conditions.
-
Product
PXIe-1486, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO FPD-Link™ Interface Module
787455-01
Interface
The PXIe-1486 combines the Texas Instruments Flat Panel Display Link™ (FPD-Link™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1486 makes use of a combination of FPD-Link™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable FPD-Link™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the FPD-Link™ channels. The PXIe-1486 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). FPD-Link is a trademark of Texas Instruments.
-
Product
USB 3.0 And RJ45 Cat6 To VTAC Interface
YAVAM852
Interface
USB and RJ45 sockets to VTAC VPC contactsHigh speed interface between connectors up to 1GbpsAvoids noise and interferences on signals thanks to VTAC contacts technology
-
Product
USB-8451, 250 kHz I2C, 12 MHz SPI I2C/SPI Interface Device
779553-01
Interface Module
The NI USB‑8451 is a master interface for connecting to and communicating with inter-integrated circuit (I2C), System Management Bus (SMBus), and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8451 is a portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices or toggling LEDs. The USB‑8451 can be physically located more closely to I2C/SPI devices than PCI interfaces, reducing I2C bus length and minimizing noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
Product
CAN/FlexRay/Differential Bus PXI Fault Insertion Switch - 4 Channel
40-200-004
CAN Interface
Each channel can support up to 0.3A and is rated to handle up to 100V between the wire pairs. The wire pairs have controlled transmission line impedance suited to most differential pair signaling systems, including fast CAN Bus interfaces and RS232. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
Product
CAN Interface Device
CAN Interface
CAN Interface Devices communicate using onboard transceivers for High-Speed/Flexible Data-Rate, Low-Speed/Fault-Tolerant, and/or Single-Wire CAN as well as any external transceiver. Using the NI-XNET driver, you can create applications that require real-time, high-speed manipulation of hundreds of CAN frames and signals. You can also import, edit, and use signals from Fieldbus Exchange Format (FIBEX) and Database Container (DBC) files in integrated CAN databases. The NI-XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time.
-
Product
COM Express Type 7 10GBASE-T Network Adapter Card
10GBASE-T Network Adapter Card
Network Interface Controller
- Supports up to four 10GbE copper interface (10GBASE-T)- Compatible with PICMG COM.0 R3.0 Type 7 modules
-
Product
Interface
RAR-MPCIE
Interface
The RAR-MPCIE is very small (30mm x 40.95mm x 4.7mm) and lightweight for applications deployed in highly constrained environments where platforms require minimum SWaP solutions. It is designed for those working in avionics test and simulation for field and test support, and for use in data logging in which it offers significant advantages and flexibility.
-
Product
USB-8451, 250 kHz I2C, 12 MHz SPI I2C/SPI Interface Device
779553-50
Interface Module
The NI USB‑8451 is a master interface for connecting to and communicating with inter-integrated circuit (I2C), System Management Bus (SMBus), and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8451 is a portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices or toggling LEDs. The USB‑8451 can be physically located more closely to I2C/SPI devices than PCI interfaces, reducing I2C bus length and minimizing noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
Product
Interface Board for 100 BaseT Ethernet
40-965-911
Interface
The 40-965-911 is a converter card for the 40-201 Ethernet/AFDX Fault Insertion Switch. Adapts the 78-Pin D-type connector on the front of the module to 8 RJ45 sockets and one 9-way D-type connector for fault signals. Allows the fault insertion testing of 100 BaseT Ethernet signals.
-
Product
*C Series CAN Interface Module
CAN Interface
C Series CAN Interface Modules communicate using onboard transceivers for High-Speed/Flexible Data‑Rate or Low-Speed/Fault Tolerant CAN. C Series CAN Interface Modules are either compatible with NI-XNET or the NI-985x driver, depending on model.Using NI-XNET, you can create applications that require real-time, high-speed manipulation of hundreds of CAN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time. C Series CAN Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
Product
Interface
R15-EC
Interface
The R15-EC card provides the highest level of performance and density for MIL-STD-1553A/B in an ExpressCard form factor. The R15-EC card provides 1 or 2 channels integrated with powerful API software that provides instant access to all 1553 databus functionality and data. Standard features include real-time bus playback (with ability to edit out RTs), aperiodic message insertion, error injection/detection, conditional BC branching, 64-bit, 25 nanosecond message timetagging, and “Oneshot” BC operation. The Bus Monitor mode provides 100% bus monitoring of a fully loaded 1553 bus. IRIG-B Receiver (AM or DC/TTL) Generator (DC/TTL) optionally available.
-
Product
USB-485/4, 4-Port, USB, RS485/RS422 Serial Interface Device
778476-94
Serial Interface
The USB‑485/4 interface transforms your USB port into a single asynchronous serial port for communication with RS485 and RS422 devices. You can use a USB‑485/4 port as a standard serial port from your application, including RTS/CTS hardware handshake lines. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
PCIe and PCI Avionics Interface Cards
Interface
Ballard PCI Express (PCIe) and PCI Avionics Interface Cards enable computers to interface with a variety of avionics databuses for testing, validating and simulating commercial and military avionics equipment and systems.
-
Product
ARINC PCI Express One Lane Interface Card
PCIE1L-A429
Interface Card
The ARINC PCIE1L-A429 Interface Card and AltaAPI Support Software Represent the Latest ARINC 32-bit FPGA Protocol Engine Technology. Encode and Decode almost Any ARINC-429 PHY Level Label/Word Signal. The First Card in the Industry to Offer Advanced Test Functions of Signal Generation and A/D Signal Capture. The one lane card PCIe is the industry first low profile
-
Product
ARINC 3U/6U CompactPCI Interface Card
CPCIC3/6-A429
Interface Card
Alta Data Technologies’ CPCIC-A429 interface module offer a variety of ARINC-419/429/575/573/717 channel configurations with software selectable RX/Tx channels, baud rates, bit encoding and word configurations (Start/Sync/Stop length, Parity, bits/word, MSB/LSB).Encode or decode almost any ARINC-429 physical layer signal.
-
Product
PCI-8232, IEEE 488 GPIB Instrument Control Device for Windows
778742-01
Interface
The PCI-8232 is a plug‑and‑play IEEE 488 interface for PCs and workstations with PCI expansion slots. The PCI-8232 can sustain data transfer rates up to 7.8 MB/s using HS488 and is IEEE 488.2 compatible. The PCI-8232 includes a license … for the NI-488.2 driver software, which provides high performance and maximum reliability for connecting to third-party instruments using GPIB.
-
Product
PCI Express Interface Card
MPCIE2-1553
Interface Card
he MPCIE2-1553 is a mini PCI Express Full-Mini Type 2 Interface Card for 1 or 2 MIL-STD-1553 channels in an incredible small package. The MPCIE2-1553 implements the latest MIL-STD-1553 32-bit FPGA Protocol Engine Technology (AltaCore-1553) with the industry leading Multi-Layer Software development software package (AltaAPI).
-
Product
COM Express Type 7 10GbE Optical Fiber Network Adapter Card
10GbE Optical Fiber Network Adapter Card
Network Interface Controller
- Supports up to four 10GbE optical fiber interfaces (SFP+)- Compatible with PICMG COM.0 R3.0 Type 7 modules
-
Product
ARINC Interface Cards
Interface Card
- Wide Selection of COTS ARINC Interface Cards/Boards and Real-Time Appliances- 4-48 Shared and Dedicated, Independent RX/TX Channels- Portable FPGA AltaCore Design – Reduced Parts Obsolescence Risk- Most Advanced Error Detection and Injection Available- Parametrics Variable Voltage on ENET-A429P
-
Product
COM Express Type 7 10GbE SFP+ Network Adapter Card
CEI-2x10G SFP+
Network Interface Controller
- Support up to two 10GbE SFP+ interfaces- Inphi CS4227 inside- COM.0 R3.1 Type 7 compliant- Dedicated for Express-VR7
-
Product
Network Interface Card
NIC10GBT
Interface Card
The NIC10GBT is a dual port 10GBase-T XMC module that brings 10GbE expandability to new and existing embedded systems with available XMC slots.
-
Product
PXI Remote Control Interface Cable, 7m
41-924-700
Remote Interface Cable
The 41-924-700 is a 7m cable accessory for the PCIe to PXI Remote Control Interface Kit. The kit provides a seamless connection between a PC’s PCIe slot and a PXI chassis and is suitable for providing an interface to any PXI chassis.
-
Product
3U CompactPCI® 2/4-Port Gigabit Ethernet Card
cPCI-3E10/3E12
Ethernet Interface
The cPCI-3E10 Series is 3U CompactPCI Gigabit Ethernet peripheral card equipped with Intel® 82574L PCIe Gigabit Ethernet controllers. The cPCI-3E10 provides four GbE ports on the front panel (RJ-45) with two switchable to the rear transition module, the cPCI-3E12 provides two GbE ports on the front panel (RJ-45), and the cPCI-3E10-SUB provides two Fast Ethernet ports on the front panel (DB-9). An optional Rear Transition Module (cPCI-R3E10) is available to provide rear access to the GbE ports switched from the cPCI-3E10 front panel.
-
Product
PXIe-8245, 4-Port, 10/100/1000BASE-T PXI Ethernet Interface Module
787313-01
Ethernet Interface
The PXIe-8245 supports Ethernet-based communication between PXI hardware and external instruments and devices. This PXI Ethernet Interface Module includes four RJ45 10/100/1000BASE-T Ethernet interface ports in a single-slot PXI Express module.
-
Product
Interface Board, Low Cost, 8:1 Ethernet RJ45
40-965-901
Interface
Low cost converter card for 40-736 Data Communications Multiplexer. Adapts the 78-Pin D-type connector on the front of the module to 9 RJ45 sockets. Allows the multiplexing of up to 8 Ethernet signals with speeds up to 1G bit.
-
Product
Enhanced Serial Interface Module for the Multiprotocol Excalibur 4000 Family of Carrier Boards
M4KSerialPlus
Serial Interface
The M4KSerialPlus is an enhanced serial interface module for the multiprotocol Excalibur 4000 family of carrier boards, that includes several advanced features such as a high baud rate and high throughput. This module supports up to four independent channels of serial communications, each of which can be selected as RS-485, RS-422 or RS-232. The module operates independently of the host computer, reducing the need for host intervention.The M4KSerialPlus module is based on the Exar XR16M570 Universal Asynchronous Receiver/Transmitter (UART). The device is compatible to industry standard 16550 UARTs. Each of the M4KSerialPlus’s four channels contains a transmit FIFO capable of holding up to 16384 bytes and a receive FIFO capable of holding either 16384 receive bytes or 5460 bytes with a 32-bit Time Tag associated with each byte. These large buffers allow application code to transfer large quantities of data with a single non-blocking subroutine call. The 32-bit Time Tag on receive channels is very useful for synchronizing serial data with data from other modules on the 4000 board or on other interface boards. Each channel has a programmable baud rate of up to 10 Mbps and can be configured as RS-232, RS-422 or RS-485.The M4KSerialPlus module is supplied with C drivers, including source code.
-
Product
USB Interface for 1-2 MIL-STD-1553 Channels
NLINE-U1553
USB Interface
The NLINE-U1553 implements the latest USB 3 SuperSpeed technology for 1-2 dual redundant, independent 1553 channels. Full function capability for Bus Controller (BC), multi-RT (mRT), and Bus Monitor (BM). Also, o-scope signal capture on the first channel to troubleshoot bus signals. All built-in a small, rugged cable assembly that allows the customer to easily connect with standard 1553 jack connectors, or make their own custom cable with a Lemo break-away standard. USB 2 backward compatible (but not recommended – USB 3 offers superior throughput performance).
-
Product
SpaceWire PXI
318a
Interface
The SpaceWire PXI card is a versatile SpaceWire Interface, Router or RMAP target device. The card is designed to be an efficient host interface to a SpaceWire system or network, by utilising a cPCI or PXI backplane.
