Parallel Interfaces
See Also: SCSI, Serial Interfaces
-
Product
PXI 32 Chan I/O Parallel I/P Prog Threshold
40-412-101
Digital I/O
A 32-channel Digital I/O module with high output voltage and current capability and a dual variable threshold input. Each of the 32 channel outputs can be used to drive the output high or low using a high current capacity drive capable of sourcing 0.4A from the high side or 0.5A sink on the low side for each channel. The module is available in two versions with either serial or parallel capture of the input levels.
-
Product
9 Pin Breakout Interface
VSI-Breakout-9
-
The VSI-Breakout-9 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
Isolated Interfaces
-
Isolate high-speed digital signals with ST's robust, reliable and flexible digital isolated interfaces.
-
Product
I2C Fast Mode Interface for USB 2.0, I2C Multimaster and Monitor
Connii MM 2.0
-
telos EDV Systementwicklung GmbH
Connii MM 2.0 is a small, compact, easy-to-use solution for a PC driven I2C transmitter and receiver. The I2C interface works as an I2C multimaster device. Thus, it is able to drive buses running multiple I2C bus masters. Additionally, Connii MM 2.0 is a limited I2C monitor for traffic up to 400kHz.
-
Product
USB/GPIB Interface High-Speed USB 2.0
82357B
-
Easily connect to GBIP instruments from a USB port; no switches, no PC cards, and no external power supplies required.
-
Product
Interface Module
MC
-
The MC mezzanine module is designed to receive external commands and issue synchronization pulses on the TTLTRG line (for VXI and other devices) and the LVDS line (for LXI devices).
-
Product
Bench/portable Universal Counters With USB Interface 3GHz Or 6GHz
TF900 Series
-
Frequency, period, pulse width, frequency ratio, duty cycle, and event counter modesDC to 3000 or 6000MHz range, 0.001mHz resolutionHigh impedance measurement up to 125 MHzAC or DC coupling, 1M/50Ohm selection, polarity invertSwitchable attenuator, threshold controlNoise filter for low frequency measurementsSelectable measurement time; display hold functionLarge 10 digit display with full range of annunciatorsInternal rechargeable batteries for portable useUSB interface provides full remote control and readback
-
Product
Parallel Differential Battery Tester With Integrated Chamber
-
Accelerate your battery parallel test using our PDBT. Featuring an integrated chamber, it precisely conducts battery comparison test and fast measures battery's self-discharge current. Its portable, powerful design is perfect for innovative research applications.
-
Product
RS-232 to RS-422 Interface Converter
Model 253
-
FEATURES: DB9 Data Port; Compatible with PC/386/486; Full Duplex; Surge Protection. Adding an RS-422 interface to a PC is now a snap. The Model 253 Interface Converter does this for full duplex signals at data rates up to 19.2 KBPS, without requiring any AC or DC power. With only TD, RD and ground, the Model 253 provides operation over 8,000 feet of twisted pair into a load of 120 Ohms.
-
Product
NI-9871, 4-Port, RS485/RS422 C Series Serial Interface Module
779892-03
Serial Interface
The NI‑9871 adds RS485/RS422 serial ports to CompactRIO systems. The serial ports are accessed directly from the FPGA to offer you flexibility in communicating with serial devices. The module has individual buffers on every port that save FPGA space and simplify programming. The NI‑9871 supports standard start bit, stop bit, and handshaking settings. It uses an external power to provide maximum compatibility and reliability under all serial port conditions.
-
Product
78-Pin Connector To Screw Terminal Interface
GT96078
Interface
78-Pin Connector to Screw Terminal InterfaceTerminal board interface. Interfaces to 78 pin connector.
-
Product
Interfaces
-
Channel link cable. Allows two scopes to be linked together to give 4 analog and 16 digital channels. Requires the four channel software to be installed.
-
Product
CAN Interface Device
CAN Interface
CAN Interface Devices communicate using onboard transceivers for High-Speed/Flexible Data-Rate, Low-Speed/Fault-Tolerant, and/or Single-Wire CAN as well as any external transceiver. Using the NI-XNET driver, you can create applications that require real-time, high-speed manipulation of hundreds of CAN frames and signals. You can also import, edit, and use signals from Fieldbus Exchange Format (FIBEX) and Database Container (DBC) files in integrated CAN databases. The NI-XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time.
-
Product
Octal Small Form Factor Pluggable Electrical Interface
-
Eoptolink Technology Inc., Ltd.
Eoptolink is developing OSFP(Octal Small Form Factor Pluggable) a new pluggable form factor with eight high speed electrical lanes that will initially support 400 Gbps (8x50G or 4x100G). It is slightly wider and deeper than the QSFP but it still supports 32 OSFP ports per 1U front panel, enabling 12.8 Tbps per 1U switch lot. OSFP is designed to support the next generation of 800G optics modules that will use eight lanes of 100Gbps, and offers backwards compatibility with 100G QSFP.
-
Product
USB Controlled Loudspeaker & Microphone Test Interface
AmpConnect™ ISC
-
AmpConnect ISC is an all-in-one audio interface that simplifies your test setup and operation. It is a single, rugged, rack-mountable piece of hardware containing a high-accuracy audio interface, impedance box, amplifier, headphone amplifier, 2 microphone power supplies and digital I/O. It replaces multiple hardware devices, connecting to your computer via a single USB cable, and it is fully controlled by SoundCheck. This simplifies setup and calibration, eliminates cabling and reduces connectivity errors, as well as reducing overall system cost.
-
Product
PMC Intelligent Interface Card
IIB-3910-PMC
-
The IIB-3910-PMC is an slot intelligent interface card providing complete STANAG 3838 and STANAG 3910 test, simulation and bus analysis capability for the PCI Mezzanine standard.
-
Product
Thermocouple Interface Amplifiers
-
Analog Devices offers specialized precision thermocouple interface amplifiers that provide a simple and effective solution for measuring thermocouple temperatures. With features such as integrated cold junction compensation and a high gain precision instrumentation amplifier, these thermocouple amplifiers provide a complete signal conditioning system in one IC package. ADI’s thermocouple amplifiers are suitable for use in diverse environments to measure a wide range of temperatures. These products will save you in cost, space, and unnecessary circuit design across a broad range of applications and industries.
-
Product
PXIe-8510, 2-Port PXI Vehicle Multiprotocol Interface Module
784121-01
Interface
2- or 6-Port PXI Vehicle Multiprotocol Interface Module—The PXIe‑8510 is a hardware-selectable controller area network (CAN) and/or local interconnect network (LIN) interface for developing applications with the NI‑XNET driver. The PXIe-8510 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
Quad Serial FPDP Interface with Virtex-6 FPGA - 6U VPX
Model 57611
-
- Four or eight channels of serial FPDP interface- Fully compliant with VITA 17.1specification- Fiber optic or copper serial interfaces- One or two Virtex-6 FPGAs- Up to 2 or 4 GB of DDR3 SDRAM- PCI Express interface up to x8- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available
-
Product
Analog Interface Module
HD588
-
Analog interface module with 3-way galvanic separation 3000V.
-
Product
PXIe-8510, 6-Port PXI Vehicle Multiprotocol Interface Module
784122-01
Interface
2- or 6-Port PXI Vehicle Multiprotocol Interface Module—The PXIe‑8510 is a hardware-selectable controller area network (CAN) and/or local interconnect network (LIN) interface for developing applications with the NI‑XNET driver. The PXIe-8510 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
PXI RS232 Interface Galvanic Isolation
PXI‑8432/4 - OTP2-Modul-Nr196
-
The PXI‑8432/4 module is a high-performance, dielectric-proof interface for high-speed communication with RS-232 devices. The module offers data transfers via the high-speed DMA interface, multithreading and multiprocessor support. NI serial ports appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Microphone Pre-Amp Audio Interfaces
-
Analog Devices mic pre-amp audio interfaces provide a high fidelity, high performance solution for audio products. Specifications for this family include ultralow 1.5 dB noise figures, 140 dB gain range, and high gain capability. Operating in an extended industrial temperature range of –40°C to +85°C, this portfolio of mic pre-amp audio interfaces supports many applications, including precision instrumentation, active filters, low noise amplifier front ends, surveillance systems, computerized voice recognition, and a variety of other industrial and consumer products. As the first choice for serious audio engineers, Analog Devices mic pre-amp audio interfaces can give your applications the performance needed to meet the most demanding specifications.
-
Product
IEEE-488 GPIB Device Interface IC (Chip) for the PCI-Bus
GPIB-72120
-
The i72120 GPIB-Chip is the ideal solution to implement a IEEE488.2 GPIB interface for next generation PCI based instruments. The GPIB-ASIC is designed to meet all of the functional requirements for talker and listener (TL) devices as specified by the IEEE Standards 488.1-1987 and 488.2-1987. Connected between the PCI bus and the GPIB, this GPIB-IC provides high-level management of the GPIB to unburden the processor and to simplify both hardware and software design. The i72120 is fully compatible with the PCI specification and requires only the addition of bus driver/receiver components to implement a talker/listener GPIB interface.
-
Product
Incorporated a Convenient LabView Interface to the Output
LabView VIs
-
Several VIs are available for plotting and monitoring pulse parameters. Update rates can be adjusted as well as the plots. The VIs are intended to be easily understood and easily modified for your particular application.
-
Product
Interface And Load Box
MS 3646I
-
Interface and Load Box is standard portable 19” rack mountable unit. It is customized unit for single channel tester of IFCC. This unit has cable/harness interface between CPCI System and IFCC LRU. This box also houses all actuator loads and switching circuits.
-
Product
10 Gigabit Ethernet AdvancedTCA® Fabric Interface Switch Blade
aTCA-3430
Switch Blade
The aTCA-3430 is a high performance 10G Fabric switch blade for AdvancedTCAR platforms. This product is ideal for bandwidth intensive telecom applications such as wireless access controllers, DPI/security network, IPTV, IP multimedia subsystems, RNC/BSC, broadband access/bearer networks, data centers, and LTE/4G network applications. The aTCA-3430 provides 10GbE hub-to-node connectivity and integrated switch silicon that supports load balancing, priority queues, packet classification, and flow control to enable strict bandwidth management for implemented applications.
-
Product
SIP-90-3 Test System Interface Probe
SIP-90-3
ICT/FCT Probe
Overall Length (mil): 700Overall Length (mm): 17.78Rec. Mounting Hole Size (mil): 55Rec. Mounting Hole Size (mm): 1.40Recommended Drill Size: #54 or 1.40 mm
-
Product
PXIe-1486, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO FPD-Link™ Interface Module
787453-01
Interface
The PXIe-1486 combines the Texas Instruments Flat Panel Display Link™ (FPD-Link™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a … high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1486 makes use of a combination of FPD-Link™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable FPD-Link™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the FPD-Link™ channels. The PXIe-1486 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). FPD-Link is a trademark of Texas Instruments.
-
