Parallel Interfaces
See Also: SCSI, Serial Interfaces
-
Product
CANbus Controller Standard Interface
PCI360
-
The PCI360 CANbus controller PCI card is based on the SJA1000. The SJA1000 provides an interface to the popular CANbus that support both standard (11-bit) and extended (29-bit) identifier messages. LEDs provide diagnostics information.The CAN network is a serial communication protocol which efficiency supports distributed real-time control with a high level of reliability.
-
Product
PXIe-1487, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO GMSL™ Interface Module
787458-01
Interface
The PXIe-1487 combines the Maxim Integrated Gigabit Multimedia Serial Link™ (GMSL™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1487 makes use of a combination of GMSL™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable GMSL™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the GMSL™ channels. The PXIe-1487 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). GMSL is a trademark of Maxim Integrated Products, Inc.
-
Product
IDE Controller PMC with 40-pin Interface Connector
5251
-
The IDE Controller PMC, when mated to a host or carrier card, provides an interface between the PCI bus and as many as four IDE/ ATA devices, via two independent channels.
-
Product
Interface RS-485 and RS-422
-
The RS-485 specification meets the requirements for a truly multipoint communications network, and the standard specifies up to 32 drivers and 32 receivers on a single (2-wire) bus. Some RS-485 transceivers modify the input impedance to allow up to 8× more nodes to be connected to the same bus. Analog Devices offers a wide range of standard RS-485/RS-422 transceivers and iCoupler® isolated RS-485/RS-422 transceivers to suit many applications.
-
Product
Compatible Bi-Directional Serial Data Interface
PMC-BiSerial-IO-II
-
The PMC BiSerial has been updated to be even better. Building on the knowledge and experience gathered from multiple IP and PMC BiSerial implementations and adding in the latest technology has created the PMC-BiSerial-II. The BiSerial II features completely isolated FIFOs with 32 bit ports for increased adaptability and performance.
-
Product
PCI 48 Channel TTL Digital Interface
8005
-
The 8005 digital I/O interface provides 48 channels of buffered drive digital I/O emulating 8255 mode zero, which can be utilized for PC based control and automation of equipment including sensors, switches, security control systems, and other industrial automation systems. 10K pull-up resistors are included. Optional values are available.
-
Product
Universal Input/output Module With CAN Interface
PCAN MicroMod
-
As a plug-in module, the PCAN-MicroMod represents a simple way of providing electronic circuits with I/O functionality and CAN connection. The configuration is carried out with a Windows program that transfers the configuration data to the module via CAN. Several modules can be configured independently of one another on a CAN bus.
-
Product
Signal Conditioners & Interface
-
Modbus RTU Remote Connectivity and Control. Minimize Long Cable Runs with Modbus Network. Pulse to Frequency Conversion. Shaft Speed Pulse to DeviceNet. Shaft Speed Pulse to 4-20 mA Conversion.Sensor Compatibility
-
Product
GPIB PC/104 Interface Card & Cable
GPIB-PC104-XL
-
The ines GPIB PC/104 interface card uses the enhanced features of the ines GPIB chip , resulting in a reliable solution for industrial measurement.
-
Product
Quad Serial FPDP Interface with Virtex-6 FPGA - XMC
Model 71611
-
- Complete Serial FPDP solution- Fully compliant with VITA 17.1 specification- Up to 2 GB of DDR3 SDRAM- PCI Express interface up to x8- LVDS connections to the Virtex-6 FPGA for custom I/O
-
Product
Network Interface Controller
SPIDAR®
-
User interface and data acquisition embedded on the NIC:1. Any device with Wi-Fi can be used to change settings or view data collection2. No data collection interruption or data loss occurs if connection to PC or device is interrupted. No reduction in speed compared to running a single system. Daisy-chain NICs to deploy any number of GPR systems simultaneously; build Multi-frequency systems or Multi-channel Array systems Advanced timing control to ensure no interference between GPR systems
-
Product
PC/104 8-Channel Smart Sensor Interface
518
-
Measures thermocouples, RTDs, strain gages, thermistors, 4-20 mA, voltage and resistance 8 high-accuracy differential input channels Integral sensor excitation Exclusive pulsed excitation minimizes sensor self-heating Configurable sensor type per channel Fully electronic calibration Low power
-
Product
Serial Analog Interface
Model 2361B
-
* Model 2361B-24 Provides four isolated analog outputs with programmable ranges.* Provides four isolated high-current drive signals and 8 digital inputs. * Includes 4 floating analog inputs.* 1 U high rack mount kit mounts one or two 2361Bs.* Includes US 115 VAC Power Adapter* Compatible with our earlier 2361 and 2361As.
-
Product
8 GHz Differential Probe with ProLink Interface
DH08-PL
Differential Probe
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
PC/104p Compatible Bi-Directional Serial Data Interface
PC/104p-BiSerial
-
The PC/104p BiSerial has been ported from the PMC BiSerial II. Building on the knowledge and experience gathered from multiple IP and PMC BiSerial implementations and adding in the latest technology has created the PC/104p--BiSerial. The BiSerial features completely isolated FIFOs with 32 bit ports for increased adaptability and performance
-
Product
Network Interface for Compact PCIe
cPCIe-ASM-NIC
-
Avionics Interface Technologies
Quad port FC-AE-ASM Network Interface Controller for Compact PCI Express
-
Product
2 Channels, MIL-STD-1553/1760 Communications Interface
FTK
-
Based on the MIL-STD-1553 signal and interface backbone, MIL-STD-1760 defines a standardized electrical interface to address additional aircraft weapons stores management and as such, includes some special requirements. The FTK module meets the operational requirements within the general specifications of MIL-STD-1760 as applied to an integrated I/O function module, and include special designed holt transceivers to ensure signal parameter operation and integrity.
-
Product
High Parallel Tri-Temp Pick-and-Place Handler
Delta MATRiX
-
Cohu’s MATRiX handler has a highly flexible test site configuration that’s well suited for a wide range of test applications, including analog ICs with short test times and high throughput, automotive devices requiring accurate thermal control, small pitch wireless-communication products, high parallel microcontroller testing, MEMS device testing, and many other device market segments with their unique requirements. The MATRiX has a highly flexible test site configuration that enables customers to reuse existing load-boards, including boards made for competitor’s legacy handlers.
-
Product
6U Single VME Slot Intelligent Interface Card
IIB-3910-VME-2C
-
The IIB-3910-VME-2C is a 6U single VME slot intelligent interface card providing complete STANAG 3838 andSTANAG 3910 test, simulation and bus analysis capability, for two 3838 dual redundant and two 3910 buses, which support optical dual redundant and electrical single redundant 3910 protocols.
-
Product
Handler/Prober Interfaces
IFXX
-
FETtest offers a variety of Interface options, which expand test capability and provide connection to other production line resources. These interfaces range in complexity from simple handler/prober interfaces to interfaces with user programmable external component connections, to capacitance measurement systems. Models are available to work with the full range of FETtest systems and Remote Stations.
-
Product
SIP-90-2 Test System Interface Probe
SIP-90-2
ICT/FCT Probe
Overall Length (mil): 700Overall Length (mm): 17.78Rec. Mounting Hole Size (mil): 55Rec. Mounting Hole Size (mm): 1.40Recommended Drill Size: #54 or 1.40 mm
-
Product
Ethernet To Modbus RTU Interfaces
-
ICS's Ethernet to Modbus Interfaces provide Modbus TCP/IP to Modbus RTU serial conversion and Raw Socket (Telnet) to control Modbus RTU Slave Devices. Available in small Minibox™ and OEM board formats. OEM board has Ethernet, GPIB and USB interface ports. All Interfaces include the VXI-11 protocol for use with: LINUX, UNIX, SunOS, Apple OS X, HP-UX, IBM-AIX and Windows 2K or later Windows systems.
-
Product
Shuttle Bus VMC Intelligent Interface Card
IIB-SB-VME
-
The Shuttle Bus VME is an intelligent interface card providing all Launch Data Bus, Ground Data Bus, andMultiplex De-Multiplex Multiple Remote Terminal capability to the Shuttle Bus, as required by NASA specification84K01203 (Hardware Specification, Launch Data Bus (LDB) and Ground Data Bus (GDB) Interface Board).In summary, this card provides all features and functions required to meet the above specification, in a VMEplatform, with Simplex & Half-Duplex modes provided. Specific operational modes provided include LDB_BCT,LDB_MRT, GDB_BCT, GDB_MRT, BUS_MON, MDM_MRT, Primitive and Calibration modes.
-
Product
Quad Serial FPDP Interface with Virtex-6 FPGA - PCIe
Model 7811
-
Model 7811 is a member of the Cobalt® family of high performance XMC modules based on the Xilinx Virtex-6 FPGA. A multichannel, gigabit serial interface, it is idealfor interfacing to Serial FPDP data converter boards or as a chassis-to-chassis data link. The 7811 is fully compatible with the VITA 17.1 Serial FPDP specification. Its built-in data transfer features make it a complete turnkey solution. For users who require application-specific functions, the 7811 serves as a flexible platform for developing and deploying custom FPGA processing IP.
-
Product
GPIB to Ethernet to Instrument Interface
Model 4865B
-
* Adds a GPIB Interface to Instruments with a VXI-11 or Raw Socket Ethernet Interface.* Transparent data transfer handles ASCII and binary data.* Controllable with any IEEE-488.2 GPIB Controller* VXI-11 protocol supports control, abort and reverse channels.* Raw Socket protocol includes substitute command strings for GPIB Device Trigger, Device Clear and Interface Clear.* Auto-Find feature simplifies instrument linkage* Reuses existing test software with new Ethernet instruments.* Easy configuration with the 4865B's internal webserver.* Drop in replacement for the original Model 4865 with 2x to 5x speed increase.* 1 U high rack mount kit mounts one or two 4865Bs.* Includes universal 115/230 VAC Power Adapter.
-
Product
USB Axis Module
E1735A
Interface Module
The E1735A USB Axis Module is the electronic interface for the 5519A/B laser head used in the Keysight 5530 Laser Calibration System. It also provides the interface for the 10888A remote control unit (optional) and the A-quad-B encoder input (optional).
-
Product
Interface Converter
ZET 7177
-
ZET 7177 CAN→GSM interface converter can be used under conditions when there is no access to a regular connection over Ethernet, or when you need to provide a redundant channel in case of Ethernet fouling.
-
Product
CAN FD interfaces and Analysers
-
CAN FD Interfaces and AnalysersCAN FD interfaces and analysers with easy to use CAN bus software with optional support for OBDII, J1939, XCP/CCP, CAN transmit, and reading of DBC files.
-
Product
Software & Hardware Interface
XJAPI
-
The XJAPI is a simple-to-use DLL Application Program Interface (API), designed to give you low-level access to the JTAG chain via either the XJLink or the PXI hardware, allowing easy integration with a wide range of other systems such as development/evaluation boards, test systems
-
Product
DISCRETE TMTC INTERFACE BOX
-
The Discrete TM/TC Box is a 6U custom 19’’ rack equipment that could be filled with 6U, 4HP plug-ins covering the main ECSS compliant discrete I /Fs. The I/O signals of this box are all arranged in the rear side of the box, keeping clear the front side: in this way no accidental operation could be performed on the box.
