Parallel Interfaces
See Also: SCSI, Serial Interfaces
-
Product
Multiprotocol PCI/104-Express Interface Board
8000PCIe104
-
The EXC-8000PCIe104 is a multiprotocol PCI/104-Express interface board for embedded applications or avionics test and simulation applications. Each board holds up to four independent modules and 10 discrete channels.
-
Product
ARINC 664 Part 7 Test & Simulation Interface for PCI
PCI-C664-V2
-
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfacesSimulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboardError Injection including Runt Frames, Short IFG, and Invalid MAC FCS - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Complete Solution for Developing & Testing Discrete Voltage-Level Interfaces
M8KDiscrete
-
The M8KDiscrete module provides a complete solution for developing and testing discrete voltage-level interfaces. The M8KDiscrete contains control I/O registers that are memory-mapped and may be accessed in real time. The module supports ten programmable I/O discretes that can record or control the external discretes that are connected to it. In addition, the module can record changes in the input discrete with an associated time tag via a built-in FIFO. Output discretes are open collector, capable of handling up to 32V with a maximum sink current of 100 mA each.
-
Product
CPCI BUS Interface Card
Cpci301 MIL-STD-1553
-
MIL-STD-1553 A, B & McAir MULTI PROTOCOLS Simulator / Analyzer / Tester CPCI BUS Interface Card - The CPCI301 can be used for Validation Testing, Production Testing, full bus simulation and monitoring, as a general purpose 1553 interface or a stand alone bus Analyzer. For precise message scheduling and measurements, the Major and minor frame times are independent of message sequences or retransmissions on errors and the start of all command messages are independent of message length, response time or length of response. Message timing is calibrated and RT responses have low jitter.
-
-
Product
HMI Operator Interface Panels
-
- Robust and powerful HMI for operation and monitoring- Programmable and parameterizable to IEC 61131-3 with CODESYS- Vibration and shock resistant housings with high protection rating- Units for surface or panel mounting- Powerful interfaces for various communication tasks
-
Product
Interface Card - 1-2 Channels of MIL-STD-1553 Networks on a PMC Form Factor with Ethernet Backplane Interface
PMCE-1553
Interface Card
PMCE-1553™ is an innovative product that provides 1553 operations via 10/100/1000 Ethernet IP/UDP local area networks (LAN) backplane. PMCE-1553 is a standard PMC form factor card, but instead of PCI backplane, PMCE-1553 uses the P4 connector for Ethernet based control and communications.
-
Product
DDS Function Generator, Digital Control 10MHz Or 20MHz, With/without USB/RS232 Interfaces
TG2000 Series
-
0.001Hz to 10MHz/20MHz frequency range6 digits or 1mHz resolution1ppm stability and 10ppm one year accuracyLow distortion, high spectral purity sine wavesInternal phase continuous sweep, lin or logAM, FSK, gated and tone switching modes5mV to 20V pk-pk from 50 or 600 OhmsStorage for multiple instrument set-upsUSB and RS232 Interfaces (TG2000 only)
-
Product
CAMAC Controller With USB Interface
CC-USB
-
The CCUSB is a full-featured CAMAC Crate controller with integrated high speed USB-2 interface and full CAMAC dataway display. It supports Master and Slave operations with complete CAMAC arbitration as well as auxiliary CAMAC controller operation.
-
Product
Interface Systems
-
To build a complete and accurate force measurement system, it’s essential to integrate a compatible sensor, instrumentation, and proper cables and connectors. Start with a high-quality load cell or torque transducer that suits your application needs. Pair it with compatible instrumentation, such as a signal conditioner, digital display, or data acquisition system, that can properly excite the sensor and interpret its output. To ensure signal integrity and reliable performance, use shielded, appropriately rated cables and connectors designed for your environment and sensor type. When all components are correctly matched and system calibrated, the result is a precise and dependable measurement system.
-
Product
2U Through 6U Customized RF Interface Unit
1257A-C
Interface
The Astronics 1257A-C is a sixth-generation RFIU tailored to your specifications. It comes with a new easy-to-use LXI Core 2011-compliant device and new enhanced features, including 2U through 6U configurations.
-
Product
Interfaces
-
Used for the collection of signals from many types of transducers and laboratory instruments. They connect to Windows and Macintosh computers via USB, and are supplied with Chart and Scope software for real-time display and analysis of the recorded signals. In addition, the EChem software module offers both traditional and advanced techniques for electrochemists.
-
Product
ARINC 429 Test & Simulation Interface for PCI
PCI-C429
-
Avionics Interface Technologies
4, 8, 16, or 32 Software Programmable Tx/Rx Channels - Programmable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection - Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/FilteringIRIG-B time code encoder/decoder with free-wheeling modeApplication Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
CAN/FlexRay/Differential Bus PXI Fault Insertion Switch - 8 Channel
40-200-008
CAN Interface
This PXI Fault Insertion module is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This module supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses. Each channel can support up to 0.3A and is rated to handle up to 100V between the wire pairs. The wire pairs have controlled transmission line impedance suited to most differential pair signalling systems, including fast CAN Bus interfaces and RS232. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
Product
PCI 16 Isolated Input Digital Interface (10-30V)
8006H
-
Optimized for sensing up to 24V inputs, the 8006H PCI digital I/O interface provides 16 optically isolated inputs for connection to devices including sensors, switches, push buttons, and other user inputs.
-
Product
PXI 32 Chan I/O Parallel I/P Prog Threshold
40-412-101
Digital I/O
A 32-channel Digital I/O module with high output voltage and current capability and a dual variable threshold input. Each of the 32 channel outputs can be used to drive the output high or low using a high current capacity drive capable of sourcing 0.4A from the high side or 0.5A sink on the low side for each channel. The module is available in two versions with either serial or parallel capture of the input levels.
-
Product
Parallel Electrode SMD Test Fixture
16192A
Test Fixture
The 16192A test fixture is designed for impedance evaluations of side electrode SMD components. The minimum SMD size that this fixture is adapted to evaluate is 1(L)[mm].
-
Product
Interface
RPCIE-1553
Interface
Abaco Systems RPCIE-1553 is the latest generation of performance and flexibility for MIL-STD-1553 A/B Notice II on a native PCI Express module. Available in -40°C to +70°C temperature with one, two or four dual-redundant channels, the RPCIE-1553 includes advanced API (Application Programming Interface) software that reduces application development time.
-
Product
PCI 16 Reed Relay Output Digital Interface
8003
-
The 8003 PCI digital I/O interface provides 16 Reed relay outputs provide high quality, long-life, low current (10 Watt maximum), dry contact switch closures. Reed relays are well suited for low-current applications. The relays are normally open, and close when energized. Writing a 1 to the proper port bit can individually energize each relay.
-
Product
GPIB to Quad Serial Interface
Model 4896
-
* Provides four RS-232/RS-422/RS-485 Serial Channels.* High speed, 115.2 K baud channels include 60 K byte buffers.* > 600 K byte/sec. GPIB data transfer rate.* SCPI commands set serial configuration and GPIB address.* LCD display shows Bus activity, buffer status, serial interface signals and channel settings.* 1 U high rack mount kit mounts one or two 4896s * Includes US 115 VAC Power Adapter, Manual and Support CD.
-
Product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196A
Test Fixture
The 16196A surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results - reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement - now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
Product
PCI Express 16-Port RS-232 Serial Interface
7161e
-
The 7161e provides sixteen RS-232 serial ports capable of data rates to 460.8K bps. Each RS-232 port implements all modem control signals for maximum compatibility with a wide range of peripherals. The board is PCI Express X1 compliant and utilizes 16C854 UARTs to provide 128-byte Tx/Rx FIFOs for maximum reliability in data intensive applications.
-
Product
CAN interfaces and Analysers
-
CAN interfaces and analyzers with easy to use CAN bus software with optional support for OBDII, J1939, XCP/CCP, CAN transmit, and reading of DBC files.
-
Product
Network Interface Card
PMC-GBIT-DT2BP
Interface Card
The Ethernet network interface complies with the IEEE 802.3 specifications for 10BaseT, 100BaseTX, and 1000BaseT over category 5 twisted-pair cable. Full-duplex and half duplex modes are supported. The PMC-GBIT-DT2BP is compliant with standard singlewide PMC IEEE P1386.1, PCI 2.2, and PCI-X 1.0 specifications.
-
Product
cPCI Intelligent Interface Card
IIB-1553-CPC
-
The IIB-1553-CPCI is an intelligent interface card providing full MIL-STD-1553 test, simulation and bus analysis capability for the CompactPCI bus, with 1553A, 1553B, McAir and STANAG 3838 capability on a single card.
-
Product
VME Sequencer PCI Express to VME Interface
SIS3104-2
-
The SIS3104-2 is the Artix-7 based successor to the SIS3104 board. It is backward compatible to the SIS3100/SIS3104 standard models and can be used as a drop in replacement. With two Gigabit/s link firmware transfer rates in excess of 160 MByte/s are possible im combination with the SIS1100-e2 single lane PCI Express card.
-
Product
NI-9860, 2-Port, C Series Vehicle Multiprotocol Interface Module
783703-03
Interface Module
2-Port, C Series Vehicle Multiprotocol Interface Module - The NI‑9860 is a hardware-selectable HS/FD controller area network (CAN) and/or local interconnect network (LIN) interface for developing CAN and/or LIN applications. As part of the NI‑XNET platform, the NI‑9860 works well for applications requiring high-speed manipulation of hundreds of frames and signals while taking other data acquisition measurements in the same CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same CompactRIO chassis.
-
Product
Fibre Channel Test & Simulation Interface for PCI-X
PCI-X-FC4
-
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
-
Product
GPP-95-2 Test System Interface Probe
GPP-95-2
ICT/FCT Probe
Overall Length (mil): 375Overall Length (mm): 9.53Rec. Mounting Hole Size (mil): 85Rec. Mounting Hole Size (mm): 2.15Recommended Drill Size: #44 or 2.15 mm
