Parallel Interfaces
See Also: SCSI, Serial Interfaces
-
Product
Quad Serial FPDP Interface with Virtex-6 FPGA - XMC
Model 71611
-
- Complete Serial FPDP solution- Fully compliant with VITA 17.1 specification- Up to 2 GB of DDR3 SDRAM- PCI Express interface up to x8- LVDS connections to the Virtex-6 FPGA for custom I/O
-
Product
USB 3.0 Interface Module
-
SuperSpeed "USB 3.0 modules" for RF Test Enclosures eliminate conducted and radiated interference while keeping data and power signals for the USB 3.0 link untouched.
-
Product
Fibre Channel Test & Simulation Interface for PCI
PCI-FC4
-
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
Product
Combination Module: 2 Ch. Dual-Redundant MIL-STD-1553 & 8 Ch. ARINC 429/575 Communications Interfaces
CM5
-
The CM5 provides a combined function alternative which mitigates SWaP-C system integration and configuration challenges.
-
Product
PCI 24 Channel TTL Digital Interface
8018S
-
The 8018S Low Profile PCI digital I/O interface provides 24 channels of buffered drive digital I/O emulating 8255 mode zero. The board can be utilized for PC-based control and automation of equipment including sensors, switches, security control systems, and other industrial automation systems.
-
Product
SIP-90-3 Test System Interface Probe
SIP-90-3
ICT/FCT Probe
Overall Length (mil): 700Overall Length (mm): 17.78Rec. Mounting Hole Size (mil): 55Rec. Mounting Hole Size (mm): 1.40Recommended Drill Size: #54 or 1.40 mm
-
Product
15 Pin Breakout Interface
VSI-Breakout-15
-
The VSI-Breakout-15 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
Interface Module
MIRIG
-
Мезонин MIRIG предназначен для приёма сигналов точного времени, их регистрации и синхронизации совместно работающего оборудования по протоколу IRIG-B
-
Product
Handheld Gauss Meter / Tesla Meter With USB Interface And Analog Output
KOSHAVA 5
-
The Tesla Meter / Gauss Meter KOSHAVA 5 combines the functionality, stability and precision of high-quality desktop units in a portable hand instrument. At the development of the Tesla Meters / Gauss Meters KOSHAVA 5 great value was paid to easy and intuitive use of the device. The Tesla Meter is comfortably and simply operable by English and German menu driven with 4 keys.
-
Product
RS-232 to RS-422 Optically Isolated Interface Converter
Model 265
-
FEATURES: Eliminates Ground Loops; 19.2 KBPS at 2 Miles;TD and RD Indicators; Use in Pairs as Double Isolated Short Haul Modems; Use in Pairs as Double Isolated Short Haul Modem. Total isolation between RS-232 based systems and RS-422. Unique circuitry allows the RS-422 port to withstand surges exceeding 10 kilovolts.
-
Product
Smart GPIB Serial Interface Board
Model 4806
-
* Provides GPIB-to-serial and serial-to-serial data paths for serial devices with RS-232 signals.* Provides all IEEE-488.2 functions and the Status Reporting Structure.* Smart firmware automatically passes GPIB data to serial device.* SCPI commands set serial configuration, GPIB address and user's IDN message. • On board voltage regulator for operation from 5 to 15 Vdc power. • Rear panel mounting eliminates cables.
-
Product
Interface Converter
ZET 7076
-
Previously it was widely thought that it is enough to receive sensor readings and to have remote control over them. But gradually there evolved a need for remote control, i.e. people need to receive sensors readings and to control their performance via Internet (for instance, on a portable device). Such possibility simplifies quite a lot of tasks since one can control performance of a system located at the other end of the city or even a country.
-
Product
Multi-Channel, Multi-Protocol 1553 and ARINC 1/2 Size PCIe 4-Lane Interface Card
PCIEC4L-MA4
Interface Module
Alta Data Technologies’ PCIEC4L-MA4 interface module is a multi-channel, multi-protocol 1553 and ARINC ½ size PCI Express 4 Lane interface card (PMC on 4 Lane PCI Express Carrier) is supported by the latest software technologies. The PCIEC4L card is based on the industry’s most advanced 32-bit FPGA protocol engine, AltaCore™, and by a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET (MSVS 2005/08/10 C++, C#, VB .NET) architecture. This hardware and software package provides increased system performance and reduces integration time.
-
Product
One, Two, or Four Dual Redundant Interface MIL-STD-1553A/B Test & Simulation Module for PXI Express
PXIe-1553
-
Avionics Interface Technologies
1, 2, or 4 dual redundant MIL-STD-1553 bus interfaces Concurrent BC, multiple RT (31), and BM operations Full error injection and detection • Data capture filtering, 100% bus recording, and physical bus replay Multi-level Trigger for Capture/Filtering IRIG-B Time Encoder/Decoder Real-Time Recording and Physical Bus Replay Application interfaces supporting C, C++, C#, and .NET development Device Driver Support for: Windows, Linux, and LabVIEW Real Time (others provided on request) 10 high voltage (up to 30V) programmable DIO lines Flight Simulyzer GUI Analyzer software
-
Product
Wireless Interface
Quasar 7Z01300
-
The Quasar module provides a way to use Ophir sensors as a remote laser power/energy meter allowing optimum placement of the sensor and separate optimum placement of your PC or laptop with no connecting cables.
-
Product
Interface Connectors
-
High durability Interface connectors do not damage the product, side terminal by a special mechanism, and do not lock, making it suitable for automated inspection.
-
Product
Four Port RS-232 Interface
PCI-COM232/4
-
Serial ports: 4Configured: Address and interrupt configured through PCI BIOS and supplied driversMax. baud rate: to 460.8 Kbps, software selectable per channel for 115.2, 230.4, or 460.8KbpsSerial modes: 5, 6, 7, or 8 data bits; odd, even or no parity; 0, 1 or 2 stop bitsUART: 16C550 standardInterrupt Status: Each UART interrupt status read from any UARTís Scratchpad RegisterConnector: 37 position D-type with fanout cable to 4 DB-9 or DB-25 male connectorsPower: +5V only
-
Product
Parallel NTDS Isolation Tap Box
-
IXI’S NTDS parallel isolation tap box is the ideal solution for relibility tapping NTDS parallel type A, B, C, and H interfaces. It connects easily to existing cables forming a tee connection that can be used for data monitoring and acquisition over long distances without interference with your system.
-
Product
Compact Juno USB Interface
Juno 7Z01250
-
*Virtual laser power meter - From sensor to interface to PC - no power source needed*Plug and play with all standard Ophir smart sensors*Use with StarViewer free Android app to turn your smartphone / tablet into a power meter*Record every energy pulse at up to 10 KHz*Log power and energy, average, statistics, histograms and more with included StarLab application*New: Pulsed Power measurements with Thermopile sensors*New: Low Frequency Power on Photodiode sensors - power measurement based on pulse cycle (for VCSEL)*System Integrator Tools included: LabVIEW VIs, COM Object Interface*Very compact - is just an extension of the smart plug
-
Product
PXI Vehicle Multiprotocol Interface Module
Interface
PXI Vehicle Multiprotocol Interface Modules use hardware-selectable NI-XNET Transceiver Cables (TRC) to communicate High-Speed/Flexible Data‑rate CAN, Low-Speed/Fault Tolerant CAN, and/or LIN. Using the NI-XNET driver, you can create applications that require real-time, high-speed manipulation of hundreds of CAN and/or LIN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time. PXI Vehicle Multiprotocol Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
Product
Ethernet-GPIB-USB to Serial Interface
Model 9006
-
* All interfaces provide full communication with the serial device.* Ethernet port supports VXI-11 and raw socket protocols.* Controllable with Windows PC programs like C, Visual Basic, LabVIEW, VEE, etc that make VISA or SICL calls.* Controllable from MAC/UNIX/LINUX and similar computers with RPC calls.* GPIB port is IEEE-488.2 compatible.* USB port uses Microsoft supplied driver to prevent driver problems with operating system change problems.* Serial port provides RS-232 and 2 or 4-wire RS-485 signals.* Supports devices that generate asynchronous messages, devices that respond when queried and smart devices.* Internal webserver for easy configuration from any browser.* Board runs on 5 to 15 Vdc power.* Includes ICS's VXI-11 and VISA keyboard control programs.* Works with Agilent, NI and Kikisui VISA libraries.
-
Product
Datum Universal Interface
DUI
-
Datum Electronics specifically designed the Universal Torque Sensor Interface which accepts serial data, displaying the output data and a wide range of additional analogue and digital outputs, s 4-20mA, +/-5Vdc, 0-5Vdc, +/-10Vdc, 0-10Vdc as well as RS232/485 serial data.The Datum Universal Interface (DUI) interfaces with all our rotary, static, reaction, digital torque sensors and torque transducers, as well as shaft power measurement solutions.
-
Product
13 GHz Differential Probe with ProLink Interface
DH13-PL
-
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
Parallel 8-channel Hipot Tester
TH9010
-
Changzhou Tonghui Electronic Co., Ltd.
8-channel parallel output of withstand voltage, and each channel is non-interfering ■ Output: AC: 5kV/10mA; DC: 6kV/5mA ■ Insulation resistance test voltage: 0.10kV -1.00kV
-
Product
SIP-90-2 Test System Interface Probe
SIP-90-2
ICT/FCT Probe
Overall Length (mil): 700Overall Length (mm): 17.78Rec. Mounting Hole Size (mil): 55Rec. Mounting Hole Size (mm): 1.40Recommended Drill Size: #54 or 1.40 mm
-
Product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196D
Test Fixture
The 16196D surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results – reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement – now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
Product
Serial to Parallel Analysis Package
B4601C
-
Your system uses serial buses to communicate between ICs and transfer data to and from peripheral devices. Sifting through thousands of serial bits by looking at long vertical columns of captured 1's and 0's can be very tedious, time-consuming, and error prone. The Keysight Technologies B4601C serial to parallel analysis package is general-purpose software that allows easy viewing and analysis of serial data.
-
Product
Bluetooth Measurement Interface
BTC-4148
-
The Portland Tool & Die BTC-4148 is a complete interface for measuring and characterizing Bluetooth audio devices including handsets, headsets, speakers, car kits and other devices with Bluetooth audio input or output.
-
Product
VXI Register Interface Board
VXI-5524A-3
-
* 3.3V power out instead of 5 V on Digital IO bus connector* All othe specifications same as listed above for the VXI-5524A board.
-
Product
VME Intelligent Interface Card
IIB-3910-VME
-
The IIB-3910-VME is a single slot (6U) intelligent interface card providing complete STANAG 3838 and STANAG 3910 test, simulation and bus analysis capability for the VME Bus.
