Gages
See Also: Gauges, Pressure Gauges, Height Gauges, Pressure Gages
-
Product
SURFACE PROFILE GAGES
-
Steel is often abrasive blast cleaned or otherwise roughened prior to painting. The peak-to-valley height of the resultant surface profile is an important factor in the performance of applied protective coatings. Low profile may reduce coating bond strength (adhesion). Too high and the peaks may receive insufficient coverage and possibly rust prematurely. The costly application of more coating may be required if the profile is too high. For these reasons, surface profile should be measured prior to coating application to ensure that it meets contract specifications.
-
Product
Air Gaging
-
Air Gaging is the ideal solution for delivering accurate and precise measurements, even in difficult industrial conditions.
-
Product
PosiTector Inspection Kits
-
PosiTector Inspection Kits contain a PosiTector gage body (Standard or Advanced) and 3 probes – coating thickness, environmental and surface profile, as well as, accessories in a convenient hard shell carrying case.
-
Product
Digihelic Differential Pressure Controller
DH
-
The Series DH Digihelic Differential Pressure Controller is a 3 in 1 instrument possessing a digital display gage, control relay switches, and a transmitter with current output. Combining these 3 features allows the reduction of several instruments with one product, saving inventory, installation time and money.
-
Product
Mini Load Column Load Cell Compression Only with Mounting
MLC SERIES
-
The MLC Series is our miniature high capacity compression only load cell/force sensor, featuring low profile compact size for a wide range of portable and dedicated applications up to 30,000 lb The load diameter is slightly convex for accurate load distribution. Low deflection through design results in ultra fast frequency response. The MLCs are designed to be mounted in a shallow machined flat pocket or smooth flat surface, either free or fastened via a bottom 6-32 tapped hole. These load cells are manufactured from heat treated 17-4 ph stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial Environments.
-
Product
Strain & Stress Testing
-
DATASYST Engineering & Testing Services, Inc.
Using strain gaging and analysis, Datasyst can assist you in quantifying strains so you can improve your product design.
-
-
Product
Thickness gauge
-
Thickness gages are used to make precise dimensional measurements on coatings and materials such as steel, plastic, glass, rubber, ceramics, paint, electroplated layers, and enamels. Search by Specification
-
Product
Propeller and Rotor Blade Strain Measurement Systems
-
Advanced Telemetrics International
ATi Telemetry Systems are typically used to transmit data from rotating shafts or machinery to a stationary telemetry receiver. The 2040BC Miniature Strain Gage Transmitter can be connected to strain gauges adhered to propellers or rotors in order to transmit blade strain or shaft torque in flight.
-
Product
General Purpose Dual Flange Reaction Torque Sensor
TRS SERIES
-
The TRS Series reaction torque sensors offer long term reliability due to non moving parts and state of the art bonded foil strain gages. The anodized aluminum TRS Series is also available as a two axis sensor, torque and thrust, on special request. Whenever possible, the best approach for precision torque measurements is via reaction torque sensing, eliminating high maintenance and high cost of slip rings, bearings, and brushes.
-
Product
Diesel Compression Tester
34700
-
Measures cylinder pressure on diesels equipped cars and trucks. Records maximum pressure reached during engine test. Release valve allows for immediate venting and resets gage for repeat tests. Swivel end quick coupler is connected to adapters sold separately. High pressure hose is 16 1/2" long. Gage is scaled from 0-1,000 PSI and 0-70 BAR.
-
Product
Data Collection Systems
-
Data collection is an increasingly important part of manufacturing, and one of the main drivers in the movement toward electronic measuring tools with output. At the top of the Starrett line, DataSure Wireless Data Collection is a state-of-the-art system for real-time collection and recording of measurement data. transmission. From measurement to input, it reduces steps, saves time and can totally eliminate error in the data collection process. Starrett also offers several newer technology products for wire-based data collection; SmartCable for single tools and the 4-Port Gage Multiplexer.
-
Product
Fracture Mechanics Clip-on Gages
-
3 models cover a broad range of gauge length, measuring ranges and temperatures, for fracture tests in compliance with various standards.
-
Product
Fuel Injection Pressure Tester
33900
-
Test gasoline fuel pump pressure on most domestic and imported fuel injection equipped vehicles.Kit contains adapters to test all GM vehicles with Multi-port and some Throttle Body Injection (TBI). Test all Chrysler cars with Multi-port turbos and some TBI.Use on older Ford TBI systems not equipped with small Schrader test valve.Includes Large Gage with hang-up hook calibrated from 1-100 PSI (0-7.0 BAR).
-
Product
Digital Pressure Gage (DP Gauge)
DP-340 series
-
DP Gauge (Digital Pressure Gauge) DP gauge is the ideal tool for pressure measurements. Excellence in not only being built into a measuring machine or system but using by it self. Downloads data in PC by a high-accuracy measurement and a communication function such as peak HOLD etc are another features. DP gauge comes with an inspection report of a traceability certification
-
Product
Data Acquisition Software
-
GaGe provides a powerful and easy-to-use PC oscilloscope software application, GaGeScope, for use with CompuScope digitizers without the need for any programming as well as a complete library of software development kits (SDKs) for C/C#, LabVIEW, and MATLAB for custom software application development.
-
Product
PCIe Octopus Express 14-Bit Digitizer
Digitizer
The GaGe Octopus Express 83XX CompuScope PCIe digitizer board features 14-bit resolution with sampling rates up to 125 MS/s with true Effective Number of Bits (ENOB) of 11-bits with 10 MHz input.
-
Product
NI-9219, 100 S/s/channel, 4-Channel C Series Universal Analog Input Module
779781-02
Analog Input Module
100 S/s/channel, 4-Channel C Series Universal Analog Input Module - The NI‑9219 is designed for multipurpose testing. With the NI‑9219, you can measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors, as well as make quarter-bridge, half-bridge, and full-bridge current measurements, with built-in voltage and current excitation. Each channel is individually selectable, so you can perform a different measurement type on each channel.
-
Product
Strain Gauge Test
-
This test measures the structural stresses induced in equipment when subjected to various environmental and operational loads. Strain gages, which are resistive devices whose outputs are proportional to the amount that they are deformed under strain, are placed at selected locations to yield stress levels which may then be compared to design allowable limits.
-
Product
Height Gages - Electronic
-
A measuring device used for determining the height of objects, and for marking of items to be worked on with an electronic display.
-
Product
Overview About LAN Ethernet Transient-Recorders / Digitizer
-
The GaGe FCiX Cobra/CobraMax LAN digitizer features 2 channels of 8-bit resolution with a maximum sampling rate up to 2 or 4 GS/s for one channel and up to 1 or 2 GS/s for two channels and true Effective Number of Bits (ENOB) up to 7.6-bits with 10 MHz input.
-
Product
Bridge Amplifier
90376
-
This miniature, on-board, transducer amplifier is capable of supplying excitation voltage and amplifying millivolt signals from strain gage based transducers.
-
Product
Through Hole/ Donut Load Cell Compression only (1.50 O.D.)
THB SERIES
-
Our THB Series through hole donut load cells offer anoutside diameter of 1.50 inches and up to four different thru-hole diameter options per capacity range. These load cells are manufactured from heat treated 17-4 ph stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
Product
4 2/3 Strain Gage Meter (1/32 DIN)
CS3-SG
-
CS3-SG Strain Gauge Indicator has been designed with high accuracy measurement, display and communication of DC signal 0~1.0/~4.0mV or 0~10.0/~40.0mV as like as Load Cell or Strain Gauge.The meter supports Field Calibration function. It can be calibrated with sensor(Load Cell/Strain Gauge) to meet machinery structure.They are also building in 2 Relay outputs, 1 External Control Input, 1 Analogue output or 1 RS485(Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission or communication for a wide range of machinery and testing equipments applications.
-
Product
Cable Length Meters
CLM-1000
-
*Measures these AWG wire gages: 18, 16, 14, 12, 10, 8, 6,4, 2 , 1/0, 2/0, 3/0, 4/0*Measures these kcmil wire sizes: 250, 350, 400, 500, 600, 750, 1000*Eight user-programmable settings for other gages*Powered by (6) 1.5V AA batteries*Replacement calibration rods (pair) available as CLM-ROD, UPC 02721*Replacement Kelvin clips (pair) available as CLM-CLIPS, UPC 02722*Feet
-
Product
Shaft Measuring Gage with Dual Glass Linear Encoder
1100GX
-
The economical gaging system of the Model 1100-GX handles a wide variety of part lengths and configurations, resulting in fast, highly accurate measurements of cylindrical engine components. Whether it is needed for use in a lab setting or out on the shop floor, this rugged gage is adaptable to a wide variety of work environments. This versatile gage employs the latest technology in motion controls, signal processing and linear grating technology.
-
Product
14 Bit Digitizer For PCIe With 8 Channels 100 MS/s Up To 8 GS Memory
Octopus-14 Express / CompuScope Express 8387
-
The GaGe Octopus Express 83XX CompuScope PCIe digitizer board features 14-bit resolution with sampling rates up to 125 MS/s with true Effective Number of Bits (ENOB) of 11-bits with 10 MHz input.
-
Product
Torque Verification
90229
-
SDI’s 90229 is designed for calibrating tools used to apply torque including electric and pneumatic power tools, torque sensors, hand and click wrenches. The strain gage based reaction torque sensors in the bench-mount housing remain stationary while torque is applied. The housing dis-assembles by removing two snap pins, allowing the user to easily change socket sizes and capacities.
-
Product
Lan Digitizer / Oszilloscope With 8 Bit, 1x2GS/s Or 2x1GS/s Up To 8 GS Memory
-
The GaGe FCiX Cobra/CobraMax LAN digitizer features 2 channels of 8-bit resolution with a maximum sampling rate up to 2 or 4 GS/s for one channel and up to 1 or 2 GS/s for two channels and true Effective Number of Bits (ENOB) up to 7.6-bits with 10 MHz input.
-
Product
DIN Rail Mount
-
Encore Electronics offers a complete line of compact, economically priced instrumentation packaged in standard DIN rail mounted enclosures. Our products include frequency to voltage converters, strain gage amplifiers, notch filters, accelerometer conditioners, and line drivers. Overall package sizes are 3.1″ x 3.3″ x 0.9″ tall (single wide) or 1.6″ tall (double wide).
