Conductance
See Also: Battery Conductance Testers
-
product
NEON Signal Mapper
The NEON® Signal Mapper application leverages key parts of TRX’s patented NEON Location Service including sensor fusion and mapping algorithms that enable real-time 3D location and mapping within buildings. Signal Mapper’s ability to locate and geo-reference users where GPS is not available simplifies and dramatically reduces the time required for map indoor signal and sensor data.Deployed with only a small, wearable accessory and an Android device, NEON Signal Mapper is the ideal solution for professionals who conduct in-building testing of public safety and commercial networks, including public safety organizations, network operators, and indoor wireless network installers.
-
product
Imaging Photometer & Colorimeter
LumiTop 4000 / 2700
Instrument Systems Optische Messtechnik GmbH
The patented optical design permits simultaneous measurement of all three sensors in one shot. The accurate spectral measurement is used as a live reference and transferred to the complete display area of the camera. This makes for extremely short measurement times and all relevant optical tests are conducted in a single test station.
-
product
SparkFun Soil Moisture Sensor (with Screw Terminals)
The SparkFun Soil Moisture Sensor is a simple breakout for measuring the moisture in soil and similar materials. The soil moisture sensor is pretty straightforward to use. The two large, exposed pads function as probes for the sensor, together acting as a variable resistor. The more water that is in the soil means the better the conductivity between the pads will be, resulting in a lower resistance and a higher SIG out. This version of the Soil Moisture Sensor includes a 3-pin screw pin terminal pre-soldered to the board for easy wiring and setup.
-
product
6 Slot VPX PCIe Gen2 Chassis
Desert Gecko
The 6 slot conduction cooled chassis can dissipate 120W in a non-moving air environment. The fin design and wall thickness was designed and analyzed with Flowmetrics software and designed for minimum delta T offset in an average thermal load application. The design was then verified in real life enviromental chamber experiments with a sealed chassis using our 3U heat simulator modules. Data available upon request.
-
product
Immunity
ESD coupling
is used for conducted coupling of Langer ESD pulses (200ps rise time) into ICs.
-
product
Security Testing
Security/negative testing is typically conducted during development to highlight how a DUT handles abnormal conditions like very high traffic load, different frame sizes (incl. undersized and oversized frames), framed with different IFG settings, various types of errors and deviation of the signal frequency, as well as various DDoS attacks.
-
product
COMPUTERIZED AUTOMATIC RELAY TEST SYSTEM
CVRT-S16
CVRT-S8 & S16 are ideal for automatic testing of ELECTRO MECHANICAL AND READ RELAYS (only DC relays) both for static and dynamic characteristics. This system scans at one stroke, all the parameters of the relay as per definition of test procedure. The test sequence can be pre-programmed and stored in the disk. You can select the tests as per your requirement. Can include or exclude the test and you can have several options to match your test definitions. Semi skilled person can be engaged for actual testing, as he need not make any settings and need not interpret the readings. The system conducts the tests and gives PASS / FAIL indication on overall test results. If a printer is connected, each test result will be printed.Test Parameters : -> Coil Resistance.-> PickUp/Pull In /Operating Voltage or Current Linear Ramp Method or Step Method.-> Measure Pickup Contact Gap FBB-LBB V or mA-> DropAway/Drop Out/Release Voltage or Current Linear Ramp Method or Step Method.-> DropAway Contact Gap FFB-LFB V or mA-> % Release Dropaway/Pickup-> Contact Resistance of all contacts both Front and Back contacts.-> Operating Time @ Set Voltage or Current.-> Contact Bounce or Chattering Time while Operating @ above-> Release Time @ Set Voltage or Current.-> Contact Bounce or Chattering Time while release @ above-> Difference of Operate Time - Release Time.-> Bridging Test or Non Overlap Test.-> Transfer or Traverse Times while Operate and release.-> Operate Time @2nd Set Voltage or Current.-> Release Time @2nd Set Voltage or Current.-> Power Consumption @ Rated Voltage.-> Coil Current @ Rated Voltage at Room Temperature.-> Coil Resistance Corrected to 20deg C.-> Timing Waveform Graph for all active Contacts.
-
product
12-1000V AC Adjustable Non-Contact Voltage Tester
5220A
Peaceful Thriving Enterprise Co Ltd
This non-contact voltage tester, can be used to test the presence of AC voltage from12V~1000V, no need of metallic conduction, easy to read by visual and audio indication. Locates breaks along live, insulated wires and power cords. Adjustable sensitivity allows tracing of wires behind walls, around switches or receptacle.
-
product
Conductivity Meters
There are both standard and a waterproof conductivity meter, as well as a conductivity meter available for flowing water or pure water (highly recommended for specific industries) as well as the ones with different conductivity measurement ranges. An important factor is that a conductivity meter normally measures electric conductivity in µS/cm, however it can also take measurements in mg/l (for direct reading of content in dissolved solid substances). The relation is established as follows: 2 µS/cm = 1ppm (parts per million) = 1 mg/l. Compensated temperature in the conductivity meter can be automatic or by hand.
-
product
300 Mm Semiconductor Processes
With the Center Nanoelectronic Technologies (CNT), the Fraunhofer IPMS conducts applied research on 300 mm wafers for microchip producers, suppliers, equipment manufacturers and R&D partners. In the field of FEoL and BEoL we offer the following technology developments and services at Ultra Large Scale Integration level (ULSI):
-
product
Panel-mount Type Conductivity Meter (Four-Wire Transmission, For Wide Range)
HE-960HI
HE-960HI is a wide-range type sanitary electric conductivity meter that can measure over a wide range from manufacturing water up to 500 mS/cm, and enables advanced concentration management through abundant outputs. It connects conductivity sensor (FES-220/310). Cleaning-in-Place (CIP) terminal management and a reduction in cleaning solutions is also achieved through accurate surface detection.And we have developed a lineup of electric conductivity sensors that can be used in conjunction, from the conventional insertion type to the flow-through type with improved cleaning and sanitary properties.
-
product
Conductivity-Resistivity Sensor Electronics and Integral System with PVDF Sensor
2850
The Signet 2850 Conductivity/Resistivity Sensor Electronics are available in various configurations for maximum installation flexibility. The universal mount version is for pipe, wall, or tank mounting and enables single or dual (digital versions only) inputs using any standard Signet Conductivity/Resistivity sensor. The threaded j-box version can be used with these same Signet sensors for submersible sensor mounting. It is also available as a combined integral system configuration for in-line mounting and includes a conductivity electrode in a choice of 0.01, 0.1, 1.0, 10.0 or 20.0 cm-1 cell constants. The 2850 is ideal for applications with a conductivity range of 0.055 to 400,000 S or a resistivity range of 18.2 M to 10 k.
-
product
Open Frame 6U 34HP Chassis
An open-frame solution for the open-minded engineer. With moveable rear profiles (up to 2.5mm,) 3U and 6U backplane compatibility options, air or conduction cooling options and the ease of fast and simple backplane interchangeability for fluid transition between VITA and PICMG bus architectures, the Hartmann Open Frame Chassis solution is the tool for customers who need versatility, accessibility and longevity.
-
product
CARB Testing
Underwriters Laboratories Inc.
The ASTM D6007 (small chamber) and ASTM E1333 (large chamber) test methods are used by the composite wood products industry to measure emissions of formaldehyde from plywood, particle board and medium-density fiberboard (MDF), commonly known as CARB testing. Testing is conducted in environmental chambers operated at defined product loading, temperature and relative humidity.
-
product
Bulk Current Monitoring Probe
MP-50
The Current Monitoring probes may be used whenever RF current measurements are required. Current measurements are made by placing a current carrying conductor within the “sensing” window of the probe and measuring the probe’s output voltage with an RF detector. Calibration of the probe permits the conversion of the voltages measured to current. Current measurements can be made over the frequency range shown in the transfer impedance curve furnished with each probe. There is virtually no loading of the circuit and the technique permits normal operation of the device under test during measurements. The MP-50 can be used for the procedure for clamp injection when the common- mode impedance requirements cannot be met given in chapter 7.4 of IEC/EN 61000-4-6 „Immunity to conducted disturbances, induced by radio frequency fields”. The MP-50 can also be used as current monitor for BCI testing as per ISO11452-4, RTCA/DO-160 section 20, MIL-STD-461 and various automotive standards.
-
product
Control Relays
Drexelbrook manufactures a supporting line of control relays that are developed especially for use as safe, reliable, economical original equipment components in many different types of commercial and industrial products.Designed to operate from electrodes or probes contacting conductive liquids, our control relays are ideally suited for level control applications in such products as vending, dispensing, ice-making machines, water softeners, dishwashers, and coffee makers, plus many types of operating equipment in the food, drug, dairy, brewing, distilling and chemical processing industries.
-
product
Single Use Cells
S.U.C.
optek Single Use Cells have an integrated conductivity sensor and enable simultaneous electrochemical and optical measurements. Various options of line sizes and connections allow for a simple integration into bioprocessing systems from low volume research up to high volume biopharmaceutical manufacturing.
-
product
Fluorescence/UV-VIS Spectrophotometer
Vernier Software & Technology, LLC
Our affordable Fluorescence/UV-VIS Spectrophotometer is designed specifically for upper-level chemistry courses. We've combined the functionality of a fluorometer with the power of a UV/VIS spectrophotometer to allow students to easily and accurately conduct numerous fluorescence experiments with compounds such as quinine sulfate, DAPI, GFP, and tryptophan. Exchangeable LEDs ensure you get the exact excitation wavelength needed for your experiment. To conduct emission spectra experiments simply attach the Vernier Spectrophotometer Optical Fiber. The Fluorescence/UV-VIS Spectrophotometer connects directly to a computer or LabQuest. Data can be collected and analyzed using our Logger Pro software, so there is no need to train students on yet another instrument software.
-
product
Avionics Radio and Pulse Tester
T-RX
Streamline your avionics radio testing process with the CCX Technologies T-RX Avionics Radio and Pulse Tester. The T-RX is an all-in-one avionics tester that conducts 100+ tests on over 16 systems with only 1 device!
-
product
NON CONDUCT DIGITAL THERMOMETER (IBL-MTX8)
IBL-MTX8
International Biological Laboratories
This Digital Non Contact type Infra Red Thermometer with laser sensor uses temperature sensor of Thermopile 8 - 14 mm and measures temperature from -50 to 750 Degree C and also in Fahrenheit scale.
-
product
Conductivity Switches
B/W Controls offers a simple conductivity holder and electrode that can be configured for multiple measurement points.
-
product
Lab Testing Equipment
Construction materials testing laboratories should be equipped with all of the accessories and consumables for conducting the required tests. Not least because any delay in testing can result in a costly delay in a building project. However, the cost of this equipment is negligible in comparison with project costs so it makes sense to ensure that sufficient stock is in place, both before and during the construction project.
-
product
Interface
EPMC-1553-8
Abaco Systems EPMC-1553-8 is the first PMC (PCI Mezzanine Card) module to offer 8 dual redundant MIL-STD-1553B Notice II channels. Available in commercial, ruggedized and conductively cooled versions with eight dual-redundant channels, the EPMC-1553 includes advanced API (Application Programming Interface) software that reduces application development time.
-
product
ccXMC-Serial
Conduction Cooled XMC module with 16 differential IO and 12 RS-232 IO plus Spartan VI 100 FPGA. Industrial Temp. SOSA pinout. Initial design has 2 HDLC, 2 NRZ, and 3 UART ports implemented.
-
product
Carbon Sensor Conductivity Meter
HE-960LC
Can measures conductivity of low concentration. Its dual calculation circuits and software, combined with carbon sensors, enable measurements ranging without switching. The HE-960LC can be used as a process concentration meter, and also to monitor changes in the concentration of specified chemicals.
-
product
Citadel CTD-ES
Teledyne Marine RD Instruments
The CITADEL CTD-ES incorporates proven inductively coupled conductivity sensor technology with a platinum resistance thermometer and micromachined silicon pressure sensor to provide highly accurate and stable readings.
-
product
Floor Resistance Test Kit
PMK-152
The PMK-152 Floor Resistance Test Kit contains the instruments you need to take resistance measurements.The PMK-152 includes Prostat's PRS-812 Resistance Meter with 5 pound conductive rubber electrodes. You can take measurements at 10 and 100 volts with accuracy within ±5%.
-
product
Electromagnetic
Promis 10
The Promis device is a multi-frequency, multi-spacing 3 component slingram type EM System for sounding and profiling the soil. This system features a transmitter loop to produce a primary magnetic field that will induce eddy current in conductive materials. These eddy currents will generate a secondary magnetic field that will be measured with the receiver loop. This system measures the in-phase and the out-of-phase components of the secondary magnetic field.
-
product
Conductivity Sensor
ACF60-35
Knowing the conductivity of liquid samples is a key parameter to control product quality throughout the production process. The optek ACF60 conductivity sensor fulfils technical requirements of international regulations for reliable measurements ensuring quality and consistency.
-
product
6U VPX PCIe to XMC Expansion Board
VP69601
LinkedHope Intelligent Technologies Co.,Ltd.
VP69601 is a 6U VPX PCIe to XMC expansion board. Onboard there is a x8 PCIe 3.0 interface, and through a PCIe connector the x8 PCIe 3.0 turns into 2 x8 PCIe 3.0 linking to 2 XMC cards. The PCIe Switch IC on VP69601 supports DMA, so direct data transmission between peripheral cards can be realized.VP69601 can be installed in a standard VPX chassis and work as a peripheral board. VP69601 carries two XMC ports, through which users can expand various functional XMC cards needed.Apart from the traditional Air Cooling design, Linkedhope○R provides a Conduction Cooling version to guarantee working stability of VP69601 in extreme and vibration environment and in an extended working temperature from -40℃ to +70℃.
