Instrumentation
See Also: Measurement, Metrology, Instrumentation Amplifiers
-
product
Surface Resistance Meter
WL MIDGET
WL MIDGET Surface Resistance Meter is an ultra-wide range, battery operated, portable instrument for measuring Surface Resistivity and Resistance to Ground of virtually any flat surface conforming to ASTM D-257 standard method by using recommended parallel bar sensing probe. Gives simple, repeatable measurements of conductive, static dissipative, and insulative surfaces. Ranging is automatic due to the use of high-speed OP-AMP Integrated circuits being linear, with changeover points +1/2 decade on a logarithmic scale. Repeatability equals + 5%.
-
product
PXI 2-Slot BRIC Matrix, 66x8 1-Pole (3 Sub-cards)
40-562B-221-66X8
The 40-562B-221-66X8 is a high density BRIC2 matrix module with a size of 66x8 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
USB 3.2 Receiver Compliance Test Software
N5991U32A
Maximize the usage of your test instruments with a fast and reliable application to automate system calibration and USB 3.2 receiver compliance tests.
-
product
Handyscope TP450-50XM-W5
TP450-50XM-W5
The Handyscope TP450 is a power quality analyzer, connected via USB to the computer. The advanced measurement software delivered by default contains Quick Setups that allow to start mains power logging measurements without specialized instrument knowledge. With the 450 V input range, the Handyscope TP450 can be plugged directly in a (110 - 230 V) wall socket to measure the mains voltage. No additional attenuator is required. Logging mains voltage can be done at a high rate of 250 thousand measurements per second, with a resolution of 16 bit, which is equal to a 5½ digit voltmeter. The Handyscope TP450 is an accurate voltmeter, but one that performs 5000 measurements on each cycle of the mains voltage, while a standard voltmeter performs 3 measurements per second. Even with the very high measurement rate of the Handyscope TP450, the mains voltage can be measured continuously for weeks, and afterwards each period of the mains voltage can be analyzed thoroughly. Using this fast continuous measuring method, no voltage peak or dip is missed, even if it lasts just a msec. The maximum measuring duration of the mains voltage is only limited by the available hard disk space. Measuring one week takes approximately 0.69 GB disk space. During a measurement, also RMS value and frequency are logged. It is possible to measure various properties, like e.g. Minimum, Maximum, Peak to peak, Mean, Variance, Standard deviation.
-
product
Density Meter
Count on solutions from the source – Anton Paar has always been at the forefront of innovation in laboratory density and concentration measurement ever since we introduced the world’s first digital density meter. Today we offer a whole series of density meters, covering most requirements in various industries and R&D – from instruments with three-digit accuracy to the world’s most precise six-digit density meter, from handhelds to benchtop instruments. Anton Paar offers the right instrument for every application requirement – choose the density meter that best fits your needs.
-
product
FD-11605, 8-Channel, ±60 V Voltage Input Device for FieldDAQ
786469-01
The FD-11605 can measure up to eight channels with a voltage input range of ±60 V. It features 24-bit resolution with simultaneous sample rates up to 100 kS/s. The FD-11605 offers channel-to-channel isolation, which eliminates noise from ground loops and protects instrumentation circuitry from high-transient voltages of up to 1000 V. The FD-11605 has an ingress protection rating of IP65/IP67 (dust-tight and water-resistant),can operate in -40 °C to 85 °C environments, and can sustain 100 g shock and 10 g vibration. The FD-11605 incorporates Time Sensitive Networking (TSN) and features an integrated network switch and built-in power circuitry for simple daisy chaining. You program the FD-11605 with NI-DAQmx, which automatically synchronizes multiple FieldDAQ™ devices. The FD-11605 is ideal for test cell and outdoor environments.
-
product
Surface Roughness Gauges & Testers
Surface roughness gauges are used for measuring the surface roughness of a material. GAOTek’s surface roughness gauges are reliable, high quality, and affordable instruments that provide an accurate measurement. They are an efficient and quick means for inspection or testing. Our gauges are compact, easy to carry and portable, allowing the user to work in complex conditions, and are available for sale to the United States, Canada and globally.
-
product
Analog Meter Relays
Hoyt Electrical Instrument Works Inc.
Hoyt Transistorized Contactless Meter Controllers are complete, self-contained, compact instruments. The CMT Series has a variety of styles and sizes to meet your specific application requirements. These precise instruments continuously indicate any electrical variable. They provide reliable control in a single, self-contained unit, or optionally, a panel-mounted meter with remote amplifier and output relays.
-
product
PXIe-5171 Oscilloscope, 250 MHz, 250 MS/s, 8-channel
783692-01
MHDMR - Mini HDMI, I/O Receptacle PXIe, 250 MHz, 8-Channel, 14-Bit, Kintex-7 410T FPGA Reconfigurable PXI Oscilloscope—The PXIe‑5171 high-density PXI oscilloscope has eight simultaneously-sampled channels with flexible settings for coupling and voltage range. PXI oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with many channels that require up to 250 MS/s or 250 MHz of analog bandwidth and advanced PXI synchronization.
-
product
BOMBARDING A.C. MILLIAMPERES METER
A Bombarding A.C. Milliamperes Meter is one of the four instruments essential for proper luminous tube processing. This instrument monitors the level of bombarder current in milliamperes that is generated by the bombarder, through the tube being processed. It is necessary to accurately monitor the current for the tubing and electrode sizes used to ensure that the right amount is applied at the appropriate time. To do otherwise may cause damage to the electrodes, fluorescent coating inside the tube and adversely affect the glass structure.
-
product
PXI 4-slot BRIC Matrix, 168x6, 1 Pole (2 Sub-cards)
40-558-401-168x6
The 40-558-401-168x6 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
product
PXIe8862, 2.6 GHz 8-Core PXI Controller
790662-01
The PXIe8862 is an Intel Core i7 8Core embedded controller for PXI Express systems. You use the PXIe8862 for processor-intensive RF, modular instrumentation, and data acquisition applications. The PXIe8862 includes two 10/100/1000/2500BASET (Gigabit) Ethernet ports, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive, serial port, two Thunderbolt 4 ports, and other peripheral I/O.
-
product
Laser Diode
Is a Polarization Maintaining CWDM Coaxial DFB-LD for CWDM analog communication, CATV return-path, laboratory instrument, and R&D applications. This cost-effective, high reliability DFB laser chip has a selectable wavelength with range between 1270 nm to 1610 nm. The versatile DFB-CWDM also features a built-in InGaAsP monitor photodiode, built-in optical isolator and 4-pin coaxial- pigtailed package, single mode coupling, and an FC/APC connector. Contact Optilab for more information.
-
product
Light Analysis
Welcome to Thorlabs; below you will find links to detectors and instrumentation that measure the various properties of light, a subset of our entire line of photonics products. Thorlabs offers an extensive selection of instruments that measure the properties of light. Our versatile power and energy meters can be used with over 25 different sensors in order to make NIST-traceable power and energy measurements. If the convenience of a meter is not desired, our selection of detectors includes basic photodiodes (uncalibrated and calibrated), photodetectors (biased, amplified, and avalanche), CCD and CMOS arrays, position detectors, integrating spheres, and photomultiplier tubes. The Beam Characterization category contains beam profilers (camera and scanning slit), a wavefront sensor, spectrometers, and interferometers, while the Polarimetery link leads to a selection of instruments used to measure and control the polarization of light.
-
product
Polarimeters
GAOTek’s polarimeters measure the rotation of polarized light as it goes through an optically active solvent by using the polarimetric technique. To calculate the value of the solution concentrations, it must determine the measured rotation. Our instruments are also ideal for various applications such as chemical, food, beverage, and medical fields. GAOTek’s high-performance polarimeters are reliable and inexpensive equipment that provide an accurate measurement for easier inspection or testing. They are compact, easy to carry and portable to allow the user to work in complex conditions and on-site.
-
product
Regulated DC Power Supply
PAR-A Series
This instrument is a single-output, direct-current stabilized power supply of the dropper type.It is capable of high stability and high precision output with low noise.Multiple interfaces can be added selection.
-
product
Ethernet/LXI digitizerNETBOX 16-Bit Multi-purpose Digitizer - 5 MS/s on 4 Channels
DN2.591-04
The digitizerNETBOX DN2.59x series allows recording of one, two, four, eight or 16 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
product
Two Way Monitoring and Control
The Drexelbrook 560 DRX Series wireless products feature 900KHz frequency hopping, spread spectrum technology to provide a reliable, license free, wireless link between the field instrument and the control room.These wireless interface products provide a cost effective alternative to expensive hard wired connections.Using Frequency Hopping Spread Spectrum (FHSS) technology, a robust signal is provided that is virtually free from disruption due to interference.
-
product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 125 MS/s on 8 Channels, 80 MS/s on 16 Channels, 16 Single-Ended Inputs, 8 True Differential Inputs
DN2.596-16
The digitizerNETBOX DN2.59x series allows recording of one, two, four, eight or 16 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
product
Seismometers
3ESPC
A low-power and portable instrument for areas with low to moderate noise.
-
product
Portable Ohmmeters
Our portable digital ohmmeters offer true portability without any sacrifice to accuracy or functionality. These ruggedly constructed instruments are ideal for use in the workshop, field or test facilities.
-
-
product
Optical Voltage Probe
400-02
Srico’s optical voltage probe uses advanced, proprietary optical chip technology to achieve precise, interference-free measurement. Our sensor and optical fibers are made of dielectric materials. This facilitates a high degree of isolation between the voltage test point and the instrumentation system ⎯ at a safe distance of 100 meters and more. This system senses, measures, and transmits electrical data very accurately.
-
product
Measuring Instruments for Gas Leak Detection
Here you will find an overview of measuring instruments from Sewerin for gas leak detection. Our portfolio includes gas warning devices, gas leak detectors, gas concentration measuring devices, multigas meters, combination measuring devices, ethane detectors, odorant measuring instruments, biogas measuring devices and a whole lot more...
-
product
PXI 8-slot BRIC Matrix, 160x16, 1 pole (5 Sub-cards)
40-558-801-160x16
The 40-558-801-160x16 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
product
TI HDC1080 Humidity and Temperature Sensor Breakout Board
SEN-37001
Breakout board for the Texas Instruments HDC1080. This sensor is an extremely accurate temperature and humidity sensing device, with +/-0.2C temperature and +/-2% humidity accuracy typical. These specs far exceed the accuracy of ICs that came before it, including the HTU2x and SHT2x series, and improves upon the success of the HDC1050. In addition, the HDC1080 has a wide input voltage range of 3V-5V and includes temperature and airflow cutouts as recommended for the best operation. Finally, in the case of environmental changes that could cause light condensation, the HDC1080 has a built-in heater to burn off any condensate. Example code (Arduino platform) is available below.
-
product
Ungrouped
Weshine Electric Manufacturing Co., Ltd
The instrument can measure single capacitor of single phase or three-phase shunt capacitor bank without removing wires.2. The instrument has the functions of inductance, resistance and current measurement.3. The instrument has two power supply modes: External AC220 V and built-in lithium battery meet various application scenarios.
-
product
Safe Discharge Rods
These instruments will allow you to conduct the safe damp discharge of the residual charge on the cable / equipment by limiting the discharge current.
-
product
PON Power Meter
TM70B
TM70B PON Power Meter (pon test instrument) is specially designed for PON network construction and maintenance which can be connected between OLT and ONT. The voice, data, video signal (1310/1490/1550) online can be measured synchronously and optical power value (1310/1490/1550) can be displayed with this meter. It’s a useful site test tool for the engineers of PON network and maintenance operators.
-
product
PoE Service Analyzer
PSA-3002-SA
Comprehensive Assessment of 2-Pair (802.3at) PoE Service at Any PD Outlet. The only PoE Service Tester built on Sifos PowerSync® Analyzer technology.• Analysis and Troubleshooting for All Standard 2-Pair (802.3at) PoE Installations Including Type-2, LLDP Power • Provisioning• Fully Verify Interoperability of PoE Service to the PD• Verify PoE Service Safety Features• Assess Continuous Power Delivery at the PD by PD Class• Assess Transient Power Delivery at the PD• Troubleshoot Intermittent PoE Service Problems• Colorful Microsoft Excel Reporting• Portable Instrument with Rugged Carrying Case
