Product

PWB Interconnect Stress Test

-

PWB Interconnect Solutions Inc.

PWB Interconnect Solutions Inc.

Services to test the reliability of Printed Circuit Boards. PCBs).Coupon Inspection and Electrical Prescreen. Coupon Testing. Failure Location via I/R Photo Imagery. Failure Analysis.

Product

Basic Quad J-Type Analog Thermocouple Amplifier

SEN-30103-J1

-

Playing With Fusion Inc

SEN-30103-J1 - Playing With Fusion Inc

Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.

Product

RF Coaxial Probes & Probe Positioner

-

Fairview Microwave Inc.

Fairview Microwave Inc.

Fairview Microwave’s line of coaxial RF probes and RF PCB probe positioner are ideal for use with chip evaluations, signal integrity measurements, coplanar waveguide, substrate characterization, gigabit SERDES and test fixture applications. The RF coaxial probes provide return loss better than 10 dB and a maximum operating frequency of 20 GHz. The probes have a 3.5mm female interface, a pitch of 800 or 1500 micron and they can be cable-mounted. They feature gold-plated contacts and can be used by hand, with or without a probe positioner. Compliant coaxial GSG (or GS) pogo pins allow for a broad range of probing angles. The RF PCB probe positioner can hold coaxial probes, has articulated joints and delivers multi-axis positioner control. This positioner also boasts a magnetic mounting plate with on-off positioner switch.

Product

Pylon ITA Mount Linear Testfixture Cassette and ITA Frame Not Included, UUT 306 x 248 mm

MG-02 VGR12

-

MG Products

MG-02 VGR12 - MG Products

FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with aluminum backpanel for a Genrad VGR12 Pylon frame• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 306 x 248 mm (wxd)• Outer dimensions: 470 x 490 x 100 x 170 mm (wxdxh1xh2)• Designed for changeable cassette

Product

Automated Bare Board Tester with Built-In Camera

QTOUCH2404C

-

Qmax Test Technologies Pvt. Ltd.

QTOUCH2404C - Qmax Test Technologies Pvt. Ltd.

Qtouch2404C – Automated Bare Board Tester with in-built camera is designed to make automatic image capturing and probing of bare PCBs. It is designed to move on X,Y,Z directions making it possible to probe every test point. Flying Probe Tester is designed for testing high density fine pitched Single Sided / Double Sided and Multilayer PCBs for continuity and isolation using moving probes fixture –less technology.

Product

PCB GPTA02, 10 mV/g, IEPE, 1 Hz to 5 kHz, Accelerometer, Triaxial Vibration Sensor

784169-01

-

NI

784169-01 - NI

The PCB GPTA02 helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound and Vibration Input Modules, and USB-based Sound and Vibration Devices. This sensor uses the Integrated Electronics Piezo-Electric (IEPE) current excitation. The PCB GPTA02 features a sensitivity range of 10 mV/g and requires a 4-socket plug-to-3 BNC plug cable.

Product

ICT: In-Circuit Testing

XILS In-Line Handling Solutions

-

EIIT, S.A.

XILS In-Line Handling Solutions - EIIT, S.A.

Designed to cover a large number of test points, with long panels for future expansion, the XILS series of Handlers, PCB test systems in the line of EIIT - Innovative Engineering Solutions, is ready for the most demanding applications.

Product

PCIe Gen3 4K at 500 Fps High Speed Compact Camera for Testing

CB160CG-LX-X8G3

-

XIMEA GmbH

CB160CG-LX-X8G3 - XIMEA GmbH

4K at 500 Fps High speed, compact, fast camera for: Vehicle Impact, Airbag Deployment and Safety Restraints Testing, Digital Image Correlation (DIC), Projectile, Explosives, Ballistics, Combustion and Missile Launch Tracking, Fluid and Flow Visualization, Sports Broadcasting, Commercial Film, Television and Studio Production, Fluidics and Particle Image Velocimetry (PIV), Flat panel inspection (FPD), printed circuit board (PCB) examination and more.

Product

VXI Register-based Interface Board

-

ICS Electronics

ICS Electronics

VXI Register Interface mates with user's PCB to form a B or C-size module.

Product

GNSS & GPS Antennas

-

TE Connectivity Ltd.

TE Connectivity Ltd.

Our portfolio of GNSS and GPS antennas are available in a variety of mounting and placement options including adhesive, magnet, mounting hole, and direct mount. Our GNSS and GPS antennas are available in several antenna types, including external mount, enclosure, flexible PCB, patch, PCB, and stamped. Custom antenna developments are regularly undertaken to meet specific customer requirements. Our GNSS and GPS antennas portfolio includes products manufactured by TE Connectivity, Laird Connectivity External Antennas, and Hirschmann Car Communications.

Product

1.0/2.3 Connectors

-

Pasternack Enterprises, Inc.

Pasternack Enterprises, Inc.

Pasternack 1.0/2.3 connector category has many part numbers, most are RoHS and REACH compliant. 1.0/2.3 connector series in this category will terminate to coax or PCB (printed circuit board). Our 1.0-2.3 connectors are built to precise RF and microwave industry specifications. 1.0-2.3 connector series is manufactured in jack or plug gender with 50 Ohm impedance. 1.0-2.3 connectors are available in straight or right angle versions, as well as, bulkhead or mountless options. These 1.0 / 2.3 connector designs include crimp/solder, solder or solder/solder attachment methods. As with the other over 40,000 RF, microwave and millimeter wave Pasternack products, this 1.0/2.3 connector series is in-stock. Not only are these 1.0-2.3 connectors in stock, but they ship the same day as they are purchased.

Product

SparkFun Solder-able Breadboard

Large

-

SparkFun Electronics

Large - SparkFun Electronics

This is the Large SparkFun Solder-able Breadboard. A bare PCB that is the exact size as our full-size breadboard with the same connections to pins and power rails. This board is especially useful for preserving a prototype or experiment you just created on a solderless breadboard by soldering all the pieces in place.

Product

Linear Testfixture (Cassette Not Included), UTT 456 x 320 mm

MG-07

-

MG Products

MG-07 - MG Products

FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 456 x 320 mm (wxd)• Outer dimensions: 620 x 590 x 100 x 184 mm (wxdxh1xh2)• Designed for changeable cassette

Product

Probe Card Analyzers

PB6500

-

Integrated Technology Corp.

PB6500 - Integrated Technology Corp.

The Probilt PB6500 has many features that make it the ideal analyzer for all probe card technologies, including the latest probe tip geometries being used to test leading edge semiconductor devices. Its excellent electrical measurement capability and the ability to drive relays on any channel make it the best tool for probe cards with complex circuits and relays on the PCB.

Product

PCB IMIB01, 100 mV/g, IEPE, 15 kHz, 2-Pin, Accelerometer, Industrial Vibration Sensor

784176-01

-

NI

784176-01 - NI

The PCB IMIB01 is an industrial Vibration Sensor designed for permanent installations. This sensor helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound

Product

X-ray Inspection System

NEO-690Z / NEO-890Z

-

Pony Industry Co.,Ltd

NEO-690Z / NEO-890Z - Pony Industry Co.,Ltd

Off-line Microfocus X-ray Inspection System equipped with PONY ORIGINAL Direct Conversion X-ray Camera; SID-A50. Suitable for inspection of BGA, CSP, and LGA on PCB.

Product

LCR Meter, Hand Held, 20 H, 600 µF, 20 Mohm

72-8155

-

Tenma

72-8155 - Tenma

72-8155 is a 3-1/2 digit digital capacitance meter with steady operations. The meter measures resistance, capacitance and inductance. The meter has a broad capacitance measurement range and precise accuracy. It can be used in measuring the circuit designed capacitance of cable, switch and PCB layout.

Product

Open Source Logic Analyzer

Logic Pirate

-

Seeed Technology Inc.

Logic Pirate - Seeed Technology Inc.

8 channels 256,000 Samples recording size 20 MHz sampling speed, can potentially be overclocked to 60 MHz No compromise on sample size when combining different speeds or number of channels Simple configurable edge detection triggers on all inputs (simple OR trigger) Configurable ratio of samples from before and after the trigger (rolling sample buffer) 5 V tolerant inputs (LOW-level voltage < 0.8 V, HIGH-level voltage > 2.0 V) About 500 kB/s transfer speed to the PC (256 kSamples take about 0.5 seconds) Data capturing can be stopped from the host software anytime Cross platform host software for Windows, OS X, and Linux DIY-friendly 0603 parts and SOIC packages used on a 2-layer board On board 3.3 V regulator can supply up to 400 mA to an external circuit Tiny 3cm x 3cm PCB Firmware updates via built-in USB bootloader Probe cables and acrylic case available from Seeed Studio Open source PCB (EAGLE) and firmware files

Product

Complete IP Module

Scan Ring Linker SRL

-

Intellitech Corp.

Scan Ring Linker SRL - Intellitech Corp.

The Scan Ring Linker SRLTM - is a complete IP module that can be easily embedded into a CPLD, FPGA or ASIC on a PCB to reduce the complexities and costs of designing 1149.1 (JTAG) test infrastructure for designs that use multiple scan rings. The SRL IP module links any number of scan rings (secondary scan paths) into a single high-speed test bus, which permits devices on secondary scan chains to be independently tested and configured through a single 1149.1 external interface.

Product

Module Spectrum

nRF52810 Series

-

Raytac Corp

nRF52810 Series - Raytac Corp

Nordic nRF52810 solutioin features an Arm Cortex-M4 processor with 192 KB Flash and 24 KB RAM with 32 GPIO available. Supports SPI, UART, I2C, PWM interfaces with both Chip Antenna and PCB Antenna option for selection.