Wire
See Also: Contacts, Harness, Connectors
-
Product
Intelligent Tangent Delta Tester of Enamelled Wire
TD-8S
-
Shanghai Dean Electrical Co., Ltd
·Tangent Delta Tester is used for testing the curing degree of enamelcover. The curve variation of tgδ shows the curing degree of enamelled wire directly, then adjust the heating temperature of enameling oven, to get a optimal curing degree of enamelled wire, control the wire quanlity effectively.·The temperature class of enamelled wire can be tested rapidly; the enamel type of wire can be determined preliminarily.
-
Product
Plugbord
3795-1
-
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side) on 0.100"(2.54mm) centers. 3-Hole Solder Pads One Side Only. 3-hole solder pads (0.28” x 0.080”) for interconnecting multiple component leads. All pad and bus surfaces solder coated for user convenience. No pattern on reverse side, edge contacts only. Convenient easy-to-read hole marking legend on wiring side.
-
Product
Rope Tension Meter
RTM
-
The PIAB RTM Rope Tension Meter is very simple and handy to use. Simply hold and “clip” it to the rope to be tested and use the large hand screw to deflect the rope to a fixed angle. The resultant force will affect the load cell and measure the tension in the wire rope. The resultant signal is digitally processed and displayed in a selected pre programmed graduation. The PIAB RTM 20D can be graduated in kN, klbs or in ton.
-
Product
Arduino Pro Mini
328 - 3.3V/8MHz
-
It's blue! It's thin! It's the Arduino Pro Mini! SparkFun's minimal design approach to Arduino. This is a 3.3V Arduino running the 8MHz bootloader. Arduino Pro Mini does not come with connectors populated so that you can solder in any connector or wire with any orientation you need. We recommend first time Arduino users start with the Uno R3. It's a great board that will get you up and running quickly. The Arduino Pro series is meant for users that understand the limitations of system voltage (3.3V), lack of connectors, and USB off board.
-
Product
PXI RTD Simulator Module, 12 Channel, PT100
40-263-301
Simulator
The 40-263-301 is a 12-channel PT100 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
8-Pin Power D-Type Cable, Female to Unterminated, Cut Ends, 3m
40-972-408-3m-FU
Cable Assembly
The 8-Pin Power D-Type Connector to Unterminated Cable Assy is constructed from PVC insulated 56/0.3 (12AWG) Copper wire. The connector can be secured to the product by screwlocks and the unterminated connections are coded to match the connector pin designation.
-
Product
GPS Wireless Clock
-
Signals & Systems India Private Limited
GPS Clock offers an easy, cost-effective solution for accurate, synchronized time displays without expensive, disruptive installation procedures. Because there are no wiring requirements, installation times are drastically reduced. It is ideal for renovation projects, as there is no need to worry about installation work, as well as new construction. The GPS clock can be synchronized through GPS Antenna or Wireless Antenna. The display can be wall/panel / tabletop mountable. It can be used as a wireless clock to synchronize many wireless slave clocks in and around the buildings.
-
Product
LXI Matrix Switching Unit
ProDAQ 6140
-
The ProDAQ 6140 provides a relay matrix which can be fitted between the sensors and actuators on a device under test and the data acquisition and control system. It allows to separately connect/disconnect the signals from either side and to connect them to an internal bus. In this way signals can be routed via the bus to new destinations or the bus can be used to monitor or supply test signals. This allows calibrating and debugging the system without disconnecting and separating channels throughout the system wiring.
-
Product
Wire Piercing Clips
619
-
This new clip makes wire piercing much easier. Just slide the wire into the cradle and screw the pin down into the wire. This method is clean and leaves minimal wire damage. If you have to proceed to pierce the wire, do it the right way with 619.
-
Product
Digitizers
2740 Family
-
The 2740 Digitizer is a 64-channel digital signal processor for radiation detectors available in VME64 (V2740), VME64X (VX2740), and Desktop (DT2740) form factor. It offers not only waveform digitization and recording but also Multi-Channel Analysis for nuclear spectroscopy using Silicon strip, segmented HPGe, Scintillation detector with PMTs, Wire Chambers, and others. The 2740 can perform pulse height measurements (PHA), constant fraction timing (CFD), charge integration (QDC) and pulse shape discrimination (PSD) independently for each of the 64 channels.
-
Product
Cable Assembly, 160-Pin DIN41612, Female to Unterminated With Cut Ends, 1m, 45º
A1604F5-C-0A100
Cable Assembly
For applications where a 45 degree cable exit would be preferred with unterminated connections at the other end. The cable assembly is constructed from highly flexible 7/0.15 (26AWG) Silver Plated Copper Wire. If the user requires the connector to have a second fixing then the right hand connector can be fitted with the optional screwlock assembly 40-969-101.
-
Product
Short Circuit Loop Impedance Meter
AMZC-306
-
Voltage measurement up to 750V and up to 250V with resolution 0,1V ; Measurements using Uni-Schuko adapter or test wires 1,2; 5; 10 and 20m ; Loop impedance measurement with resolution 0,01Ω and much more
-
Product
PXIe 10GBase-T1 Ethernet MEMS Fault Insertion Switch, 8 Channel
42-205-008
Fault Insertion Unit
42-205-008 (PXIe) is a 8-channel fault insertion switches designed to simulate common faults on high speed two wire communication interfaces such as xBaseT1 Ethernet. They available with 4 or 8 channels of two wire serial connections and can be used for simulating faults on 10BaseT1, 100BaseT1, 1000BaseT1 and 10GBaseT1 Ethernet interfaces. Any wire can be set as open circuit and shorts can be applied across wire pairs. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to supply voltage or ground.
-
Product
PXI CAN Interface Module
CAN Interface
PXI CAN Interface Modules communicate using onboard transceivers for High-Speed/Flexible Data‑Rate, Low-Speed/Fault Tolerant, and/or Single Wire CAN as well as any external transceiver. Using the NI-XNET driver, you can create applications that require real-time, high-speed manipulation of hundreds of CAN frames and signals. You can also import, edit, and use signals from FIBEX and DBC files in integrated CAN databases. The NI-XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time.
-
Product
Electronic Counters
GR2-C Series
-
The GR2-C Series is a self-powered LCD Totalizer in small form. With a panel size of DIN 48 x 24mm, it is perfect for limited space installations. It is powered by a replaceable lithium battery that lasts approximately 7 years, no external power required. The GR2-C series is available in 7 digits with 8mm height figures with Front Reset or Remote reset options. Input signal includes dry contact, open collector, voltage, wide range voltage at maximum count speed upto 30Hz. The front panel protection is IP54 and wiring connection is easily done via the terminal block connector, making it secure and reliable. CE, UL and RoHS compliant.
-
Product
IN-LINE SPARK CHECKER KIT FOR RECESSED PLUGS
MTILSCK
-
*Test newer vehicles with recessed spark plugs and conventional and coil-on plug ignition systems*Provides information not available with OBDII code reading devices and pinpoints if there is a spark plug, plug wire, mechanical, fuel injection or electrical problem*Troubleshoots most domestic and import cars, SUVs and trucks
-
Product
Electrical Safety Tester
-
Basic testing methods of Glow wire device> and UL 746A, IEC829, DIN695, VDE0471, the Glow wire tester ZRS-3H/ZRS-3HS is suitable for resistance to abnormal heat and fire test on lighting lamps, electronic products and household appliances. Adopting high-temperature coating spraying on steel structure and imported instrument display, with easy operation, stable performance the equipment is applicable to flame resistance tests of all levels of QC departments and corresponding enterprises.
-
Product
Optical Displacement Measurement Systems
ODS Series
-
The optical displacement measurement systems of the ODS series are specially designed for measuring the ultrasonic vibration displacement at bond tools of wire & flip-chip die bonders. The systems are highly accurate and very easy to use. That makes it the perfect tool for displacement based calibration of ultrasonic bond machines.
-
Product
Cable Assembly 68-Pin Micro-D Female to Unterminated, Cut Ends, 1m, Spring Latch
40-972A-068-1m-FU
Cable Assembly
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by a Metal Spring Latch.
-
Product
Fault Finder for Electrical Wiring Open / Short Circuit
FF310
-
42 V Ready: for use in the new generation of vehicles with mixed or single 42 Volt systems. Operates on DC voltages from 6 to 42 volts. Internally protected against power surges and overloads. 8" flexible probe allows reaching wires in congested places. Transmitter and Receiver LEDs show open or short circuit conditions.
-
Product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Cut Ends, 1m, HV
A037DM5-C-HA100
Cable Assembly
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Cable, 96-Pin 1.27mm Pitch Female To Unterminated, Ferrules, Screwlocks, 1m
A096SFR-F-6A100
Cable Assembly
The 96-Pin 1.27mm Pitch to Unterminated Cable Assy is constructed from 28 AWG Twisted Pair Tinned Copper wire with Polyolefin insulation. Crosstalk is minimised. Wires are colour coded for easy connection. M2.5 screwlocks are provided on the 96-Pin connector.
-
Product
Material Science Laboratory Instruments
-
our material science laboratory instruments basically consists of four instruments first, young modulus apparatus which is used for determining the young modulus elasticity of a wire by stretching it. Then second is curie temperature kit which is used for determining the Curie Temperature. With the determination of dielectric constant of PZT material with Temperature variation. After that comes dielectric constant kit which is used for measuring the dielectric constant of solids and lastly our universal B-H Curve Tracer which is used for tracing the B-H loop which is very difficult and needs a good machinery for doing so.
-
Product
Cable Assembly 68-Pin Micro-D Female to Unterminated, Cut Ends, 0.5m, Screwlocks
A068SFR-C-6B050
Cable Assembly
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by 2-56 UNC Screwlocks.
-
Product
Circuit Breaker Finder Accessory Kit
69411
-
For use with ET300 Digital Circuit Breaker Finder.Light socket adapter for finding the correct circuit of a lighting fixture.Alligator clip adapter enables use of on bare wires.
-
Product
10 A portable digital micro-ohmmeter
MPK-253
-
The MPK-253 digital very low resistance ohmmeter is a portable, microprocessor-controlled instrument used to accurately measure resistances of switches and circuit breaker contacts, transformer and motor windings, wire and cable samples, joints in busbars, etc., using test currents from 1mA up to 10 A.
-
Product
Aerial Fiber Optic Cable
-
AFL offers a complete portfolio of fiber optic cable, supporting hardware and compression accessories that are designed to meet the most demanding transmission and distribution environments. As the leading world manufacturer of fiber optic cable, AFL is uniquely positioned to provide a full line of all-dielectric self-supporting (ADSS) aerial cables and Optical Ground Wire (OPGW) as well as supporting hardware and accessories.
-
Product
Cable + Network Tester
LinkIQ
-
The LinkIQ™ Network+Cable Tester is designed to provide trusted cable testing along with network testing professionals need to do their jobs. LinkIQ™ validates cable performance (up to 10 Gig) using frequency-based measurements and provides distance to fault information along with a wire map of the cable under test.
-
Product
PXIe-4081, 7½-Digit, ±1,000 V, Onboard 1.8 MS/s Isolated Digitizer, PXI Digital Multimeter
783130-01
Digital Multimeter
PXIe, 7½-Digit, ±1,000 V, Onboard 1.8 MS/s Isolated Digitizer, PXI Digital Multimeter—The PXIe‑4081 is the industry’s most accurate 7½‑digit DMM and provides the measurement capabilities found in two common test instruments: a high-resolution 1,000 V DMM and a digitizer. As a DMM, the PXIe‑4081 delivers fast, accurate AC/DC voltage, AC/DC current, 2‑ or 4‑wire resistance, and frequency/period measurements, as well as diode tests. In the high-voltage, isolated digitizer mode, the PXIe‑4081 can acquire waveforms at sample rates up to 1.8 MS/s.
-
Product
RF/Microwave Assembly Capability
-
Teledyne Labtech offers a comprehensive build-to-print microwave module and microwave components manufacturing service. This includes MMIC placement, Au wire bonding, SMT assembly and test.Our microwave MIC production facility is housed in a class 10,000 clean room that accommodates manual chip placement and semi-automatic wire bond assembly. Dedicated microwave components manufacturing is undertaken within production cells established to meet specific customer or product requirements.
