Filter / Amplifiers
See Also: Filters, EMI Filters, Low Pass Filters, Programmable Filters
-
Product
Automatic Level Control Amplifier
-
RF Lambda’s automatic level control amplifiers allow customers to implement an AGC function into their system to tune the gain and stay linear with high input signals without the need to manually control the input level. Hermetically sealed options are available upon request.
-
Product
SIM Filter
-
The CFL SIMF, Cable Fault Secondary Impulse Filter from SCOPE is the ultimate solution for locating underground cable faults in minimum time. It uses advanced technology for fault distance measurement which helps even an unskilled operator to locate the fault accurately.
-
Product
Charge Amplifier
CH-1200A
-
CH-1200A is a high-performance charge amplifier to convert charge signal to voltage signal. Built-in integration function allows optimization of the signal which is input to the vibration data analyzer connected.Changing into a multi-channel amplifier is easy by connecting multiple units.
-
Product
Filters
ZF
-
Antenna Technology Communications, Inc.
ATCi offers a selection of filters designed to reject out-of-band interference.
-
Product
Switching Amplifiers
-
*One- or two-channel design*Small design requiring only very little space*Programmable output function*Relay or transistor outputs*Easy mounting on DIN rail
-
Product
High Frequency Tunable Bandpass Filters
CTB Series
-
Tunable Ranges Up To 8 GHz. Bandwidths 1% to 5% of Tuned Center Frequency. Digital Control Offered in Various Inputs, including GPIB (standard), RS-232, RS-422, and USB. Custom Interfaces Available.
-
Product
General Purpose Amplifier
-
Easy to use 1.5V to 5.5V amplifiers with 69uA/ch and 150uV offsets, perfect for battery based or power concerned systems.
-
Product
Electric Transducer Driver Amplifier
7620
-
The Krohn-Hite Model 7620 is a 17/34 watt, wideband power amplifier that offers extended output power and voltage capabilities. Performance features not available in other power amplifiers, the 7620 provides a differential output and is able to deliver 17/34 watts of continuous power (68 watts at dc) and 141V/282V rms (400V/800Vp-p). It can also provide plus and minus dc voltages simultaneously.
-
Product
Low Pass and Bandpass SMA Coaxial Filters
-
Fairview Microwave’s bandpass filters were developed for use in various applications including GPS, ISM, RFID and Wi-Fi systems and operate in several bands, some as low as 824 MHz and some as high as 5.875 GHz. Fairview’s low pass filters allow for tailoring of a test setup for a specific application and support upper band edges of 100, 225, 400, 1000, 2000 and 3000 MHz. All of these bandpass filters and low pass filters feature female SMA connectors.
-
Product
AC/DC Power Pass Hybrid Amplifier
AS 1313 SMPS
-
- Low Power Consumption - Drive More Amplifiers- Special 6 Volt Module -For High OutputMultiple Power Options:- 12 Volt DC Adapter- DC Power Pass 40V- AC Power Pass upto 110 V
-
Product
Waveguide Power Amplifiers
-
RF solid state power amplifier (SSPA) PE15A4006 from Pasternack is part of the largest selection of in-stock radio frequency microwave and millimeter wave amplifiers available for same-day shipment. This Pasternack solid state RF power amplifier is a medium power amp design constructed in a connectorized package. Our SSPA is designed with SMA connectors and rated at 1 Watt.
-
Product
High Voltage Amplifier
HA-800
-
*800Vp-p(±400V DC) *70mAp-p(±35mA DC) *Bandwidth: ≦200KHz(400Vp-p) *Slew Rate: 200V/us *Gain(AMPL): 0~180(10 Turn VR) *DC Offset: ≦0~±400V (10 Turn VR + SW) *Output Resistor: 100*Ω
-
Product
Transconductance & Transimpedance Amplifiers
-
Measurements International Ltd.
0 to 100 Amps – AC, 0 to ± 100 Amps – DC, Voltage Compliance ± 5 Volts, IEEE-488 Interface, Resistive, Capacitive, Inductive Loads.
-
Product
Wide Band Filters (multi-octave)
NANO-ERF® Series
-
The NANO-POLE® Extended Range Series of tunable filters was developed to address applications needing an extremely small surface-mount package with low power consumption. Wide tuning range is accomplished with careful design to minimize size and power consumption.
-
Product
GaN 100W Power Amplifiers
PE15A5033F
-
The PE15A5033F is a 100 W high gain Class A/AB Coaxial Linear Power Amplifier operating in the 0.7 to 2.7 GHz frequency range. The amplifier offers 100 Watts typical saturated power and 45 dB minimum small signal gain with 1.5 dB typical gain flatness @ Psat. The amplifier requires typically a +30V DC power supply. The SMA connectorized module is unconditionally stable and operates over the temperature range of 0C and +50C. The unit comes with a Heatsink and Fan.
-
Product
Low Noise, High Performance, FTTP High Power Multi-port Optical Amplifier with a Gain Spectrum Band
MX5800 Series
-
Each output port for the optical amplifier has built-in high performance CWDM. Every external up-link optical port of the optical amplifier can conveniently connect with an OLT. Each of the 1550nm (CATV)’s output optical ports will multiplex 1310/1490n’s data stream from an external OLT, reducing the quantity of the components and improving the performance and reliability of the system.
-
Product
Amplifiers - Solid State
-
PMI offers a full line of RF and Microwave Amplifiers that range from 250 kHz up to 50.0 GHz. Many options are available. If you do not see exactly what you require on this website, please contact sales@pmi-rf.com because we offer amplifiers designed and built to your specifications at catalog prices.
-
Product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K0
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
QuickLink Solder-In Starter Pack for use with Dx10 Amplifier
Dx10-QL-3SI
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
Handset Power Amplifiers
-
Broadcom Handset Power Amplifiers support different operating modes (CDMA, UMTS, LTE, and GSM/EDGE) and multiple frequency bands offering premium performance in a very small form factor.
-
Product
Saluki SE1022D DSP Lock-In Amplifier (Dual-channel)
-
SE1022D Digital Lock-in Amplifier provides an excellent performance within its bandwidth from 1 mHz to 102 kHz. More importantly, SE1022D has dual independent input channels and dual independent high precision signal generators. Each input channel and signal generator can be used independently which means that the SE1022D is equivalent to two traditional lock-in amplifiers. Moreover, due to the twin symmetrical design, the two independent input channels and signal generators have ultra-high synchronicity, which meets the measurement requirements demanding extremely high synchronization.
-
Product
Gas Filter Correlation Carbon Dioxide Analyzer
Model T360
-
The Model T360 CO2 analyzer measures Carbon Dioxide by comparing infrared energy absorbed by a sample to that absorbed by a reference gas according to the Beer-Lambert law. Using a Gas Filter Correlation Wheel, a high-energy IR light source is alternately passed through a CO2 filled chamber and a chamber with no CO2 present. The light path then travels through the sample cell, which has a folded path of 2.56 meters.The energy loss through the sample cell is compared with the reference signal provided by the filter wheel to produce a signal proportional to concentration, with little effect from interfering gases within the sample. This design produces excellent zero and span stability and high signal to noise ratio, allowing excellent performance over a wide concentration range.All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.The Model T360 comes with NumaView™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.
-
Product
RF Filters - Notch
-
A specialized band-reject filter that blocks or significantly weakens a very narrow range of unwanted frequencies (the "notch") while letting all other desired frequencies pass through relatively unchanged.
-
-
Product
Precision Amplifier
-
TI Precision Labs is the electronics industry's first comprehensive online classroom for analog engineers. The on-demand curriculum pairs theory and applied lab exercises to deepen the technical expertise of experienced engineers and accelerate the development of those early in their career. This free modular curriculum includes over 30 hands-on trainings and lab videos, covering analog amplifier design considerations with online course work.
-
Product
Broadcast Filters UHF
-
RFS Waveguide UHF filters are now 4th generation products designed for global combining and filtering applications associated with DTV and analog television transmissions.
-
Product
Pulsed Injection Locked IMPATT Amplifiers
-
Pulsed injection locked amplifier incorporates IMPATT diode, ferrite input/output isolators, circulators, and pulse modulator. Only DC power supply, RF input signal, and external trigger signal are required to operate amplifier. Output phase noise parameters are very close to the noise parameters of the input RF signal.
-
Product
700 - 3200MHz 100W Amplifier
VBA3200-100
-
High reliability proven GaAs design. Class A for maximum mismatch drive. General linear power requirements. The VBA3200-100 is a 00-3200MHz high power amplifier, designed primarily for EMC applications. It is based on our GaAs technology, offering the user the benefits of linearity, ruggedness and efficiency. With its compression point close to saturated output, it is equivalent to TWT amplifiers of twice the output power.
-
Product
Servo And VFD Filters
-
Operation of PWM-driven motors – servo motors and variable frequency drives (VFD) – causes several problems in equipment, including damage to the motor’s bearings due to leakage current causing electrical discharge machining (EDM) and damage to motor’s insulation. PWM motors also are a major source of EMI in equipment. These motor drive systems use pulsed power to drive the motors. As we are aware, the sharp edges of the pulses inevitably include high frequency components which can couple or radiate as noise to other parts of your system and cause unreliability, communication/control problems and EMC compliance issues.
-
Product
Automatic Battery with Filters with Standard Contactors
BATLVF400
-
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensation of powerfactor in low voltage instalations
