Bus Interfaces
Enable bus interoperability.
See Also: Interfaces, Serial Interfaces, Parallel Interface, UI, MIPI, Interface Adapters, Bus
-
Product
High-Speed Digital Bus Test Instruments
-
Teradyne and AIT instruments test legacy and newer digital buses.The enormous variety of digital buses used in defense and aerospace applications requires comprehensive, yet efficient testing.Teradyne and AIT COTS instruments meet these challenging bus test requirements for legacy and standardized buses, as well as evolving digital buses that have faster speeds, larger data volumes, and increasingly complex protocols requiring real-time test and emulation.
-
Product
Digital Signal Processor Card for PCI bus
SI-C33DSP
-
The SI-C33DSP-PCI from Sheldon Instruments is a powerful Digital Signal Processor (DSP) card for your PC equipped with a PCI bus. It is based on Texas Instruments’ new 150Mhz TMS320VC33, 32 bit floating point DSP, and can transform your PC into an ultra high performance development system and DSP accelerator.
-
Product
USB Interface
PK-232/USB
-
The PK-232/USB brickwall filters have tighter bandwidth and steeper skirts for improved noise and QRM rejection. New PK-232 firmware (Ver. 7.2) allows a wider selection of filters than the original PK-232, so the filter can match the mode. The correct DSP filter is automatically selected when you choose an internal mode. In RTTY, Timewave’s proven Twin Peak Filters pluck the mark and space tones from the noise and QRM for great copy. In PACTOR, the filter bandwidth automatically changes when the baud rate shifts in response to the error rate of the link. In Morse (CW), the operator can preset either 100 Hz or 200 Hz bandwidth. The PK-232/USB is compatible with all Windows W2K,XP,Vista/Win7 software terminal programs for the PK-232.
-
Product
50 Pin Breakout Interface
VSI-Breakout-50
-
The VSI-Breakout-50 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
Locomotive Interface Gateway
LIG
-
Locomotive Interface Gateway (LIG) is a network communications and interface device that provides locomotive control-system data to third-party applications. The LIG is designed with an Open Message Interface which allows applications to access control-system data while providing locomotive system isolation to ensure the control system is not adversely impacted by third-party applications. The real-time parameters available from the LIG can be used to perform real-time health and status monitoring of a locomotive as well as real-time assessment of locomotive operator performance.
-
Product
Power Interface Module
SP 1250LX
-
The SP 1250LX products feature an integrated Power Interface Module (PIM) and programmable display. The LX Series are advanced Uninterruptible Power Systems (UPS) that provide clean, regulated Dual Conversion power for controllers and other sensitive equipment inside the cabinet.
-
Product
Air Interface Emulator
-
Becker Nachrichtentechnik GmbH
With help of air interface emulators radio field propagations can be emulated reproduceable in laboratory environments. For different applications like cellular, wireless networks or broadcast several types of devices are available.
-
Product
MTM Ribbon Cable Interface
-
ELEGANT CONNECTIONS: The S91-MTM-RCI-1 Ribbon Cable Interface connects non-MTM equipment into MTM-based systems. Bridge external test tools to an MTM test-point carrier board (TPCB) using wired ribbon cable, headers, or terminal blocks.
-
Product
Interface
RCNIC-A2PAX
-
The RCNIC platform is a high performance, PCI module (PMC on carrier card) for the AFDX / ARINC 664 protocol. With two independent ports for traffic monitoring, traffic generation, external triggering and analysis, the RCNIC provides high-resolution time-tagging of incoming packets simultaneously with highly accurate traffic generation.
-
Product
Peripherals & Interface Cards
-
Interface cards are plug-in modules that provide interfaces for control/communication of/with external components or test items.The modules themselves are controlled via standard interfaces such as USB 2.0/3.0, PCI, PCIe, PXI, PXIe or LAN.
-
Product
PCIe X8 Interface
96VG-NG730F16-3A
-
NVIDIA GT730 Kepler GPU Architecture. Integrated with 1GB DDR3 64-bit memory. Supports up-to 4 Monitors with HDMI. 1 Slot Compact design for industrial chassis PCIe x8 interface.
-
Product
CANdo Interface
NET50003
-
CANdo is a compact USB to CAN interface, that allows a PC to be connected directly to an embedded CAN bus. In conjunction with the FREE CANdo Application software, CANdo provides a simple, yet powerful means of testing & analysing a CAN network. The FREE CANdo SDK allows CANdo to be easily integrated into any Windows based program.
-
Product
8-Sites ISP & I2C/SPI Interface
YAV90ISP
-
Industrial Programmers Interface up to 8 targetsRelay BarrierDemultiplexer module up to 32 devicesCommunication Interfaces I2C and SPI
-
Product
Interfaces And Control Boards
-
Acts as a bridge between a machine, motor controller, or PLC and related drive amplifier, feedback device and/or software.
-
Product
Intelligent Interface Card
IIB-1553-PC104+
-
The IIB-1553-PC104+ is an intelligent interface card giving full MIL-STD-1553 test, simulation and bus analysis capability on the PC104+ bus, providing 1553A, 1553B, McAir and STANAG 3838 variants in a single card. The IIB-1553-PC104+ supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with comprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides a variable amplitude dual redundant 1553 interface. 2 Mbytes of dual ported RAM are provided. The board is supplied with C drivers in source code and Windows menu driven software as standard.
-
Product
CAN & LIN bus Custom Test & Simulation Software
CanX
-
Schleissheimer Soft- und Hardwareentwicklung GmbH
CanX is the custom testing and simulation software for CAN and LIN bus for specific user groups. The run-time software is designed to execute predefined or automated tasks in testing, work preparation, production, repair or project management.
-
Product
GPIB Serial Interface
Model 4804B
-
* Provides RS-232C single-ended and RS-422/RS-485 differential serial signals. * Functions as a GPIB-to-Serial Interface (G-Mode) or as a Serial-to-GPIB Controller for a single device (S-Mode).* Over 600 Kbytes/second GPIB data transfer rate.* Transparent data transfer.* GPIB Address can be set by SCPI commands, by an external rocker switch or by a serial command.* On board voltage regulator for operation from 5 to 15 Vdc power.* Dual GPIB headers support GPIB connections with a GPIB Connector/Address Switch Assembly or with a GPIB Flat Ribbon Cable.
-
Product
Avionics Data Bus Tester
Distributed CORVUS
-
Distributed CORVUS works in conjunction with CORVUS-300 to isolate bus anomalies and fault resolution. The Transmit unit, C-9235-TX, sends 1553 like data pattern through a bus stub and coupler to the Receive unit, C-9235-RX, on another stub. This will measure insertion loss, possible bit errors and correct polarity. The Receive unit can also be used to give a digital scope representation of the active data bus showing signal quality and peak to peak amplitude.
-
Product
Network Interface for Compact PCIe
cPCIe-ASM-NIC
-
Avionics Interface Technologies
Quad port FC-AE-ASM Network Interface Controller for Compact PCI Express
-
Product
Microphone Interfaces
MEMS
-
Listen offers 2 MEMS digital microphone measurement interfaces from Portland Tool & Die, the laboratory-grade DCC-1448 and the low cost PQC-3048 for production line use.
-
Product
2-Phase Stepper Drives Based On EtherCAT Field Bus
Nu-Step DA Series
-
The ADLINK Nu-Step DA Series is a stepper driver based on the EtherCAT bus featuring a 32-bit ARM processor and advanced variable current and frequency conversion technology. The driver generates less heat and motor vibration for more stable operation. It not only supports the standard EtherCAT specification, but also supports table comparison triggers for automated optical inspection (AOI) and linear comparison triggers for line scanning.
-
Product
GPIB To ANSI X3.28 Interfaces
-
ICS's GPIB to ANSI X3.28 Interfaces adapt older devices that use the ANSI X3.28 devices to the GPIB Bus. All ICS GPIB Interfaces are IEEE-488.2 compliant and HP-IB compatible.
-
Product
Network Interface Controller
SPIDAR®
-
User interface and data acquisition embedded on the NIC:1. Any device with Wi-Fi can be used to change settings or view data collection2. No data collection interruption or data loss occurs if connection to PC or device is interrupted. No reduction in speed compared to running a single system. Daisy-chain NICs to deploy any number of GPR systems simultaneously; build Multi-frequency systems or Multi-channel Array systems Advanced timing control to ensure no interference between GPR systems
-
Product
Interface Technology ProLine
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Isolation Amplifier for DC voltage and current measurement with galvanic isolation, active and passive standard signal isolation amplifier, supply isolation amplifier for supplying 2-wire sensors, transmitter for temperature and AC signals, isolating amplifiers for high voltages and shunt applications. T
-
Product
Mid Bus Probes
MBP850
-
The PCIE850 provides a complete test and debug solution for PCI Express Bus. Interposers and probes connect to the PCIE850 providing access to PCI Card, AMX, XMC and VPX systems.
-
Product
ARINC825 (CAN Bus) Test & Simulation Module for VME With 4, 6 Or 8 CAN Bus Nodes
AVC825-x
-
ARINC825 (CAN bus) Test & Simulation Module for VME with 4, 6 or 8 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The AVC825-x VME card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
Product
Serial Data Acquisition And Control Interfaces
-
ICS's Serial to Data Acquisition and Control Interfaces are IEEE-488.2 compliant and and provide GPIB functionality over a serial link. Click on a link or scroll down to access the appropriate Serial Digital Interface:Our Serial to Data Acquisition and Control Interfaces have non-isolated analog and digital signals. Click here for our isolated Serial to Analog Interfaces.
-
Product
5-slot ATX-supported PICMG 1.3 Bus Half-size Backplane
HAB206
-
The HAB206 has a PICMG 1.3 CPU card slot, a PCIe x 16 slot and a total of three 32bit/33MHz PCI slots. The onboard 24-pin ATX power connector and 8-pin connector for thermal detected board are featured. Furthermore, the backplane supports two onboard SATA ports (optional function). The HAB206 is perfect fit for AXIOMTEK's half-size CPU cards, the SHB210 and SHB211, which are built around the PICMG 1.3 form factor. We have an enclosure, the AX60501 and AX60530, to house the backplane.
-
Product
Interface Adapter
DMX-10
-
DMX-10 is, all-in-one ready to use PCIEx to I2C/SPI/GPIO Interface adapter based on system with FPGA and 1x PCIEx PHY. DMX-10 converts PCIEx transactions into the I2C, SPI master or slave transactions and GPIO control functions. DMX-10 turns your PC running Windows, DOS, Linux, MacOS or any embedded OS with PCI support into comprehensive general purpose bus master or slave adapter.
-
Product
Ethernet Interface Module
-
Ethernet modules for RF Test Enclosures eliminate conducted and radiated interference while keeping data and power signals for the Ethernet link untouched.
