Bus Interfaces
Enable bus interoperability.
See Also: Interfaces, Serial Interfaces, Parallel Interface, UI, MIPI, Interface Adapters, Bus
-
product
RTSI Bus Cables for 3 PCI or AT/ISA Devices
776249-03
34-Pin Female RTSI to 34-Pin Female RTSI Ribbon Cable - The RTSI Cable, sometimes referred to as RTSI, connects RTSI bus connectors on adjacent NI plug-in boards. The RTSI Cable is offered with different numbers of ribbon connections and in different lengths.
-
product
11-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB121
*Designed for PICMG 1.3 SBC*Compatible with AX61410, AX6145, AX6156 chassis*Supports one PICMG 1.3 CPU card slot, seven PCIe x4 slots, one PCIe x8 slot, and two 32bit/33MHz PCI slots
-
product
CAN interfaces and Analysers
CAN interfaces and analyzers with easy to use CAN bus software with optional support for OBDII, J1939, XCP/CCP, CAN transmit, and reading of DBC files.
-
product
Interface Technology Style VXI Module Shield Kits
*Encloses Interface Technology style, slotted-edge, C-size PC boards All kits include side shields, a pre-machined blank front panel, ejector handles, all necessary hardware and assembly instructions. * All kits are available with customized front panels and side shields.
-
product
PCI Intelligent Interface Card
IIB-1553-PCI
The IIB-1553-PCI is an intelligent interface card giving full MIL-STD-1553 test, simulation and bus analysis capability on the PCI bus, providing 1553A, 1553B, McAir and STANAG 3838 variants in a single card.
-
product
GPIB to Relay Interface Boards
Model 4864 OEM
* 114521-11 Board provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully IEEE-488.2 and SCPI compliant.* Fully IEEE-488.2 and SCPI compliant.* Includes 50-pin mating Relay connector and serial header connector.* Optional terminal board for easy connections without soldering. See the GPIB Accessory page.* Operates on 12 to 24 Vdc power.* Use an ICS GPIB Connector/Address Switch Assembly to mount a GPIB connector and Address Switch on the rear panel. • 114521-12 Board provides 16 heavy duty form A contacts (SPST).* All other specifications are the same as for the 114521-11 Board. * 114521-14 provides 16 Relay driver outputs that sink 300 mA.* All other specifications are the same as for the 114521-11 Board.
-
product
Interface Adapter. USB Solution
U2C-11
Dimax USB to I2C Bridge device - U2C-11 converts USB transactions to I2C Master transactions. U2C-11 turns your PC running Windows or Linux OS into comprehensive I2C Bus master.
-
product
Interface Converter
ZET 7176
Interface converter Ethernet/Wi-Fi↔CAN ZET 7176 is used for connection of CAN interface instrument communications nets based on digital transducers to PC over Wi-Fi or Ethernet. Wi-Fi or Ethernet network throughput rate allows to immediately fulfill commands and transmit great scope of data. Shared use of ZET7176 and ZET 7172 interface converters allows arranging instrument communications nets with radio linked transmission interface.
-
product
Ethernet To Modbus RTU Minibox™ Interface
ICS's Model 9099 Ethernet to Modbus RTU Interface is a small Minibox™ Ethernet Modbus Converter that converts Modbus TCP/IP, VXI-11 and Raw Socket to control Modbus RTU Slave Devices. The Model 9099 does not require special drivers and is compatible with the following systems: LINUX, UNIX, SunOS, MAC OS X, HP-UX, IBM-AIX, Windows 2K or later and Modbus capable PLCs. ICS's 9099 uses VXI-11 RPC calls for secure communication with virtually any computer. Easily programmed on a PC by making VISA calls or on a MAC/UNIX/LINUX computer with RPC calls. Special drivers are not required. ICS Electronics is the premier VXI-11 device supplier with 100% VXI-11 compliance in every product. See our extensive Application Notes or download our VXI-11 Tutorial and the VXI-11 Specification for more information about the VXI-11 Standard.
-
product
PCI 16 Isolated Input Digital Interface (3-13V)
8006
The 8006 PCI digital I/O interface provides 16 optically isolated inputs for connection to devices including sensors, switches, push buttons, and other user inputs. The inputs can sense both AC and DC voltage while providing optical isolation, which eliminates spikes and surges present in industrial environments.
-
product
Parallel Interface Voltage Output D/A Converters
Analog Devices offers a large portfolio of parallel interface voltage output D/A converters (DACs). We provide precision, fast settling, rail-to-rail micropower VOUT D/A converters, with resolutions of 8 bits up to 16 bits, single-channel to 40-channel density, and a unipolar or bipolar supply. These devices are used in a wide variety of applications such as process control, automotive test equipment, or digital gain and offset adjustment.
-
product
True Reference Audio Interface With MDIO Expansion
Titan
Titan and Atlas are world class multi-track interfaces offering flexible expansion and unsurpassable sonic clarity. Using the latest generation of Prism Sounds trusted conversion, Titan is ideal for music and sound recording, multi-tracking, overdubbing, stem-based mastering, analogue summing and critical listening applications.
-
product
MIL-STD-1553 Test & Simulation Interface for PCI Express
PCIe-C1553
Avionics Interface Technologies
Dual redundant, single, dual or quad stream configurationsSoftware selectable Transformer, Direct, and Bus Stub Coupling Modes - Concurrent Bus Controller, 31 Remote Terminals, & Bus monitor operation - Full error injection and detection - Multi-level triggers for capture and filtering - Ten high voltage (up from 30V) programmable DIO lines - IRIG-B time code encoder/decoder with free-wheeling mode - Real-Time recording and physical bus replay - x1 Lane PCI Express Host Interface (x4 Physical edge connector) - Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
Fibre Channel XMC Interface Module
XMC-FC4
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Supports DMA for high speed streaming of data to/from the board - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
product
Power System Recorder with CDR , PMU and IEC 61850 station bus protocol
TESLA 4000
ERLPhase Power Technologies Ltd
The new TESLA 4000 is an intelligent, state of the art, user-friendly multi-timeframe dynamic power system recorder with advanced Phasor Measurement Unit (PMU) and Continuous Disturbance Recording (CDR) capabilities. Wide area swing recording accomodates system performance analysis in minutes Meets NERC continuous disturbance recording standards with non-volatile on board flash memory No mechanical moving parts – flash drive eliminates most common mode of failure in recorders. Each flash drive holds 1000 records. IEEE C37.118-2005 SynchroPhasor Standard
-
product
CPCI BUS Interface Card
Cpci301 MIL-STD-1553
MIL-STD-1553 A, B & McAir MULTI PROTOCOLS Simulator / Analyzer / Tester CPCI BUS Interface Card - The CPCI301 can be used for Validation Testing, Production Testing, full bus simulation and monitoring, as a general purpose 1553 interface or a stand alone bus Analyzer. For precise message scheduling and measurements, the Major and minor frame times are independent of message sequences or retransmissions on errors and the start of all command messages are independent of message length, response time or length of response. Message timing is calibrated and RT responses have low jitter.
-
product
Data Interfaces, Sensors And Actuators
Dewesoft also develops and manufactures data interfaces such as CAN USB devices, GNSS and INS positioning devices, and Inertial Measurement Units (IMU), and high-speed cameras. All devices are completely compatible and synchronized with all of our Data Acquisition (DAQ) systems and offer the same highest possible built quality. To complete the measurement chain we also provide high accuracy current and vibration sensors.
-
product
Virtual Interface Technology for 3D-IC Metrology
VIT
TSV profile (depth, top & bottom CD, tilt, SWA)-Residue Detection-RST-Copper Nail Height-Bump Height and Cu pillar height-Edge trim profile
-
product
SIP-90-4 Test System Interface Probe
SIP-90-4
Overall Length (mil): 693Overall Length (mm): 17.60Rec. Mounting Hole Size (mil): 57Rec. Mounting Hole Size (mm): 1.45Recommended Drill Size: 1,45 mm
-
product
HMI Operator Interface Panels
- Robust and powerful HMI for operation and monitoring- Programmable and parameterizable to IEC 61131-3 with CODESYS- Vibration and shock resistant housings with high protection rating- Units for surface or panel mounting- Powerful interfaces for various communication tasks
-
product
RS-232 to RS-485 Optically Isolated Interface Converter
Model 8322
FEATURES: 4 Wire-Master/Slave Operation; Active Mode Control Via RTS or Data; Opto Isolation; Built-in Power Supply; Internal Microcontroller; 38.4 KBPS Data Rate; DIN Rail Mountable; Programmable Terminations. The Model 8322 RS-232 to RS-485 Interface Converter allows information exchange in half duplex mode over two twisted pairs.
-
product
8 GHz Differential Probe with ProBus2 Interface
DH08-PB2
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
product
Isolated Serial Interface Card
PCI-ICM-2S
The PCI-ICM-2S serial communications card can be installed in five-volt PCI-bus computer slots and provides effective communication on long lines in noisy environments. Data lines are opto-isolated from the computer and from each other to assure communication even when large common mode voltages and noise are imposed.
-
product
Genrad 2270 Interface Receivers
GR Series
The 3210 Series Receiver is designed for interfacing the GR 2270 style test fixture. Using patented CAM/TRAC design, the 3210 Receiver provides an accurate, positive locking system that ensures consistent contact throughout the entire interface. With a 5/8" stroke, the 3212 Receiver allows additional clearance for coax and custom block applications.
-
product
Ethernet Bridge Converter for MIL-STD-1553 and ARINC
ENETX-MA4
eNetX-MA4™ is an innovative product for “remoting” 1553 & ARINC-429/717 operations on 10/100/1000 Ethernet local area networks (LAN). eNetX-MA4 is a very small, low-power, rugged device that provides real-time UDP connectivity to for 1-2 dual redundant 1553 (A/B) busses and 4 ARINC channels. Tested to MIL-STD-704F/810G/461F and DO160.
-
product
Software & Hardware Interface
XJAPI
The XJAPI is a simple-to-use DLL Application Program Interface (API), designed to give you low-level access to the JTAG chain via either the XJLink or the PXI hardware, allowing easy integration with a wide range of other systems such as development/evaluation boards, test systems
-
product
STD Bus, Vectorbord Plugbord
4610-3
VECTOR Electronics and Technology, Inc.
56 Gold plated edge contacts (28 each side)on 0.125"(3.175mm) centers.Pad per hole and peripheral buses both sides.Row and column legends provided.
-
product
ARINC825 (CAN Bus) Test & Simulation Module for PCIe
ACPe825-x
ARINC825 (CAN bus) Test & Simulation module for PCIe with 2 or 4 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The ACP825 PCIe card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
product
30 GHz differential probe with ProAxial interface
DH30-PX
30 GHz differential probe with ProAxial interface.
-
product
Real Time Monitor Interface
ANALYSIS 4N
It supports a management on the on-site equipment, such as to add subnets, to add subnet equipment, or to config equipment parameters, etc. Subnet fulfills the following applications: parallel communication, interaction with equipment, batch logging, downloading, configuration, ending, timing synchronization and system status viewing.
