Polarization
property of transverse waves which specifies the geometrical orientation of the oscillations.
See Also: Resistivity & Induced Polarization, Resistivity, Polarizers
-
Product
Audio Fiber Tracer
CFT-810
-
Motorized Polarization Controller. In addition to its basic function of adjusting polarization states in multi channels, it also provides convenient ‘save and recall’ functions. As a Scanning PC, it provides very powerful ‘auto scan’ modes with variable scanning speeds. Polarization states can be manipulated by either manual adjustment or remote control (GPIB, RS-232) using two quarter-wave plates in each channel of the PC1600. Additionally, the auto scan mode of FIBERPRO’s Motorized Polarization Controller has been upgraded in LPC, and it shows another auto scan mode of four quarter-waveplates with higher polarization extinction ratio when connecting two channels at a high speed. PC1600 is an essential tool to complete fiber-optic, multi-channel measurement systems such as WDM/DWDM as well as R&D (i.e. PMD experiments), and manufacturing.
-
Product
High Gain Horn Antenna
BBHA 9120 K
-
The BBHA 9120 K is a linear polarized high gain horn antenna for immunity testing at short distances, especially optimized forAutomotive 600 V/m Pulse Radar Test 1.2 - 1.4 GHz. Standard: General Motors: GMW3097, Ford: EMC-CS-2009.
-
Product
Biosensor isoPod with USB
EPU352
-
A compact signal conditioner for monitoring low current, two-electrode (anode and cathode) amperometric sensors. By setting the polarization voltage to zero it can also be used as a zero resistance ammeter (ZRA).Electrical isolation ensures that readings are not influenced by nearby current sources such as conductivity, or voltammetric electrodes.
-
Product
Terminal Test Kit (92 Pcs)
3601C
-
Peaceful Thriving Enterprise Co Ltd
*Total: 92 pcs*Alligator clip x 2 pcs*Testing probe x 2 pcs*Flat terminal x 48 pcs*Testing needle x 4 pcs*1 to 2 connector x 2 pcs*Round terminal x 24 pcs*5K variable resistor x 2 pcs*Polarity tester/stroboscope x 2 pcs*SRS air bag replacement connector x 2 pcs*Male / Female to Male / Female Extension Wire x 4 pcs
-
Product
Pyroelectric and Thermal Testing
-
The optional Chamber Task measures the Pulse Polarization response and Small Signal Capacitance of a Pyroelectric material that is being heated and/or cooled within a thermal chamber, on a hot chuck or in a furnace. From these measurements the Spontaneous Polarization Pr(q) and the Dielectric Constant er(q) are computed. These are then combined to determine the Electrical Displacement D(q) as a function of the temperature q.
-
Product
Through Hole type DC Current Sensor／for DC Leakage Current Measurements
DCZCT-20M
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*DC earth fault measurement for solar power system*Least affection from the magnetization of core and temperature fluctuation*DC leakage current measurements*Current measurements for small DC motor*Convenient ＋5V single polarity power supply
-
Product
S-Band Planar Antennas with 8 dBi Gain
LS-08-PS
-
The Lumistar LS-08-PS S-Band Planar Antenna is the ideal companion to the LS-25/27/28 Series Receivers to provide a low cost receiving system with extremely high performance. This small, lightweight antenna is available in various polarizations. The Standard version offers the quickest delivery, but other versions including ones with Polarization Diversity. Combining (dual linear with ±45 slant range) is also available.
-
Product
Intelligent Battery Charger-Analyzer for Large Battery Systems
SuperMasterCharger
-
The SuperMasterCharger is an instrument designed to charge, trickle charge and analyze ( discharge ) Nickel-Cadmium, Sealed Lead-Acid and other types of rechargeable batteries. With its multiple modes of operation: Constant Current Charge ( dual and single rate ), Constant Current & Float Charge, Constant Current & Peak Stop Charge, Automatic Discharge ( analysis ), Resistance Discharge ( analysis ) and Full Discharge ( deep cycle ). The SuperMasterCharger can satisfy the requirements of most large ( 10 A-hr to 100 A-hr ) rechargeable battery systems. The instrument features safety interlocks to protect the operator, the charger and the battery in the event of reversed polarity connection, short circuit, open circuit ( no load ) and Over-voltage conditions. Two large LED digital meters permit the simultaneous monitoring of voltage and current, while eight indicator lights display the status of the operation.
-
Product
1.5µm PM Ev-Yb Fiber Amplifier ( PM EYDFA )
HAPM5000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HAPM5000 is a C-Band Polarization Maintaining Optical Amplifier which worked in 1540~1570nm operating wavelength. Adopt Polarization Maintaining (PM) Multiclad Ev-Yb fiber, output optical power range 27~37dBm(0.5W~5W) ， extinction ratio >20dB.
-
Product
Voltage Tester, LED
72-9395
-
*Easy to use voltage tester designed for the professional user*Waterproof and rugged making it ideal for nearly all situations*Continuity test*690V max*Short circuit detection*Automatic range selection*Single lead voltage detection*Phase rotation test (50-60Hz)*Polarity detection*Built-in LED light*Rubberised grip*12 month limited warranty *view Terms & Conditions for details
-
Product
Smart Surge Protector
SSP-50X
-
Progressive Industries Smart Surge Protectors (SSP) are portable RV surge protectors with the added benefit of a built-in polarity tester. The built-in surge indicator notes the condition of the surge protector. Additionally, the polarity tester (dual line for 50A) checks the status of the power source prior to use. Sleek, compact, portable design makes it easy to use and store. Designed for outdoor use. No installation required.
-
Product
Polarization Tester
-
Polarization Tester is used to measure the stress value of optical glass, glass products and other optical materials, and is widely used in pharmaceutical companies, glass products factories and laboratories.
-
Product
S2 Blinx Digital Sensors
ULP-S2 BLINX
LED Sensor
The Universal LightProbe S2 Blinx Digital is designed for the simple ON/OFF test of any color blinking or steady-state LED, for fast results with a digital output. The Universal LightProbe S2 Blinx Digital Sensors check the ON/OFF status of any color LED, whether stable or blinking/pulsed, up to a rate of 15 Hz, and provide a Logic “1” output (5 volts) only if the LED is “ON” and a Logic “0” if the LED is “OFF.”Operating temperature range: 0oC to 70oCPower consumption: Operates from +5, 12, 24 or 28 volts D.C., at 6mA max.Voltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsSignal Output Load: 20mA max. (Source/Sink). Non-inductiveOutput Pins: 3 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. longOperating Temperature Range: 0hC to 70hCTypical response times: <66mS, shorter for brighter LEDsFiber-Optic Probes: Wide Aperture Fiber-Optic Probe recomended
-
Product
A Ready-to-use Solution To Orientate Polarization Maintaining Fibers Inside Connectors
PM ALIGNER-V2
-
PM Aligner-V2 is the simplest way to orientate precisely a PANDA Polarization Maintaining fiber inside a connector or ferrule. With a long working distance, PM Aligner-V2 allows the operator to work manually around the ferrule of the connector. After positionning, the curing phase becomes easy to realize without affecting on the PM fiber alignement.
-
Product
Bench Power Supply, Adjustable, Fixed, 3 Output, 0 V, 32 V, 0 A, 3 A
72-13600
-
*Triple channel linear DC power supply*Dual channel adjustable & one channel fixed*Constant current & constant voltage operation*Forced ventilation & temperature cooling system*LED digital tube display shows voltage and current simultaneously*Low ripple & low noise, output on/off control*Overload and reverse polarity protection*115VAC/230VAC (50Hz/60Hz) AC input voltage and 0.01% high regulation*12-month limited warranty *view Terms & Conditions for details
-
Product
Probe Antennas
-
Probe antennas are offered as both standard and custom models with a rectangular waveguide interface. Probe antennas can only support linear polarization. These antennas are often used to measure the gain of other antennas by comparing the signal levels of the probe antenna and antenna under testing. The standard models operate across the full waveguide band and offer 6.5 dB nominal gain and 115 and 60 degrees half power beamwidth at center frequency. The below standard offering covers the frequency range of 8.2 to 170 GHz.
-
Product
Digital 5KV High Voltage Insulation Tester
Model KM 6305IN
-
Kusam Electrical Industries Limited
• Microprocessor-controlled.• Tests insulation resistance up to 10 TΩ • 4 Insulation test voltages: 500V, 1000V, 2500V, 5000V.• AC / DC Voltmeter.• Short-circuit current up to 5mA• PI (Polarization Index) indication.• DAR (Dielectric Absorption Ratio) indication.• Auto-ranging on all insulation ranges.
-
Product
Polarity Tester
PT-1
-
International Electro-Magnetics, Inc.
The PT-1 provides a simple and easy way to determine the relative polarity of coil windings. It allows for an in-process test that takes a minimum of time to perform. By placing a coil on the platform and making connection to the start and end of a winding, a test signal is induced in the winding. The induced signal is low level and completely safe for the operator. By comparing the test signal phase of the coil under the test output, the relative polarity is indicated by the Red/Green LED. The tester operates by inducing a signal voltage in the coil under test by means of a magnetic flux field. The field is generated by a coil located in the probe base. The coil configuration is designed to provide optimum field distribution. We have also applied this basic circuit to a 5-channel scanning unit.
-
Product
Static Locater/Meter
90930-10001
-
Easy to use+/- 10% Accuracy20 KV at 1 inch with polarity automatically selected.Can measure higher values be increasing distance to target. Size 11 X 6 X 2.5 cm ( 4.25 X 2.5 x 1 inches)Weight 150 gm (5 oz)
-
Product
Oil Testers
-
PeakTech Prüf- und Messtechnik GmbH
This device was developed for the quick and reliable testing of frying oils in the catering trade, commercial kitchens and also for private users. With the device settings it is possible to display the oil temperature of the deep fryer. By measuring the TPM value (Total Polar Materials) the content of polar substances can be determined, which is a reliable parameter to characterize the extent of aging of the frying oil / frying fat during frying.
-
Product
High Performance Liquid Chromatograph Triple Quadrupole Mass Spectrometer
LCMS-8045
-
Equipped with a heated ESI probe, the LCMS-8045 has the highest sensitivity in its class. The heated ESI probe, high-temperature heating block, desolvation line (DL) and drying gas, all act to promote desolvation and prevent contamination due to the penetration of liquid droplets into the MS unit. This improves the robustness, so reliable and high-accuracy data can be obtained over the long term. The LCMS-8045 also achieves the world's fastest scan speed (30,000 u/sec) and polarity switching speed (5 msec). These enable ultra-high-speed, high-sensitivity analysis. The excellent cost performance of this system is demonstrated in food safety, environmental analysis, and other quantitative analyses, it can be upgraded to the LCMS-8060.
-
Product
Minirator
MR-PRO / MR2
-
The Minirator MR-PRO provides a full set of analog audio signals including sine wave, pink noise, white noise, delay test signal, polarity test signal, stepped sweep and continuous sine sweep. Further, a set of wav-files, useful for system optimization, is stored in the internal flash memory. Add your own personal favorites to this set.
-
Product
Waveguide Twists
-
Waveguide twists and bent types of waveguides are used extensively in electromagnetic devices. Twist waveguides are used to change the polarity of the fields. Waveguide twist VSWR is as low. Both 45° and 90° waveguide twists are available. The 45° versions being available in both right hand and left hand twist configurations.View more Twist Waveguides
-
Product
Power modules
-
G.R.A.S. Sound & Vibration A/S
It provides polarization voltage for the transducer, ensuring that the microphone gets the charging voltage it needs.It provides supply voltage for the microphone preamplifier. The preamplifier acts as a unity gain impedance converter. It provides a certain amount of line drive capability by providing a low output impedance and output current, making it possible to transmit the signal from the transducer to the Power Module without significant degradation.A power module can provide amplification or attenuation to the signal, thus making it possible to fine tune the measurement chain to the signals being measured and the hardware being used.Selectable filters make it possible to exclude unwanted noise from the measurement, e.g. wind induced noise from outdoor measurements.Overload detection makes it possible to validate the measurements and is a useful tool in monitoring setups.When a Power Module with gain is used, you can use longer cables because of the power module's ability to deliver current.A Power module introduces electrical isolation
-
Product
Optical Backscatter Reflectometer
OBR 4600
-
The Luna OBR 4600 Optical Backscatter Reflectometer (OBR) is a powerful tool for testing and analyzing loss in short-run networks and components. The OBR 4600 is an ultra-high resolution reflectometer that features a spatial sampling resolution of 10 microns, zero dead zone, and backscatter-level sensitivity. The OBR 4600 offers industry leading technology to precisely track loss and polarization states, allowing you to “see inside” your components and systems.
-
Product
Acoustic Imager
-
Can be used for quick on-site testing of current transformers in metering installations. They are designed and manufactured to test transformers’ primary current, secondary current, and turns ratio and identifies phase type and polarity.
-
Product
POWER PROBE VOLTMETER
MDPPVT
-
*Quickly tests for voltage*Reads 5V - 35V*Can be checked on reverse polarity
-
Product
Piezoelectric Testing
-
Radiant Technologies, Inc. specializes in the measurement of electrical and piezoelectric properties of non-linear materials. The Piezoelectric Task captures a sample's displacement as a function of voltage profile along with the sample's polarization response. An external displacement measurement instrument must be attached to a Radiant Precision Test System to make this measurement. All of the Radiant testers are equipped with a high-impedance voltage input to capture the output of a displacement sensor. Every Vision measurement task will collect data from that sensor input simultaneously with the measurement being executed. Radiant's test systems work easily with displacement sensors which include:
-
Product
Reverberation Tent
-
This product is a chamber made of metal flexible fabric tent assembled as a cavity that provides a periodic electro-magnetic environment randomly polarized, spatially uniform, and isotropic.
-
Product
High-Voltage Test Device
PGK 70 HB
-
Cable testing and diagnostics with the BAUR PGK HB. There are hardly any other longer-lasting, more robust and cost-effective testing devices than the two-piece high-voltage test devices from the PGK HB series. They generate continuous adjustable test voltages with mains frequency or optionally DC with positive or negative polarity. The display instruments for current and voltage, the safety control unit and the regulating transformer for the voltage are integrated in the operating unit.* Testing of medium- and high-voltage cables* DC voltage testing of up to 70 kV output voltage with positive or negative polarity* AC voltage testing - up to 55 kV for switchgear, busbars and insulating elements* Easy-to-maintain 2-piece design
