Connectors
dock multiple contact or data junctions.
See Also: Interconnects, Mass Interconnect, Cable Assemblies, Contacts, Harness, Wire, Test Point, Cable Assembly
-
Product
Digital/Analog/Frequency Measurement Module
JT 2149/DAF
-
The JT 2149/DAF is a compact, mixed-signal (Digital/Analog/Frequency) measurement module for use in JTAG Technologies’ widely-used JT 2147 (QuadPod) signal conditioning interface. The DAF module has been designed to replace a regular TAP Pod and provides 28 measurement channels plus a clock generator. When connected to a circuit board via edge connector or test fixture/jig test pins, the module enhances standard digital boundary-scan tests by enabling a series of analog and frequency measurements to be made.
-
Product
PXI High Density Multiplexer, 2-Bank, 40-Channel, 2-Pole
40-615A-010
Multiplexer Module
The 40-615A-010 is a 2-bank, 40-channel, 2-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
Product
PCI Analog Output Boards
PISO-DA2U
-
Universal PCI, 2-Channel Isolated Analog Output Board. Includes two CA-PC09M D-Sub connectors
-
Product
PXI Single 2 Channel (M Mode) SC 50 Cons
40-855-212-M50
Switch Module
Fiber Optic MEMS Switching cards available in many high density formats with a choice of five different connector styles to suit most applications
-
Product
Precision Pink Noise Generator
Noise Plug
-
The NOISE PLUG is a complete precision pink noise generator built in a XLR microphone connector. Inside the NOISE PLUG is an ultra wideband, avalanche junction white noise source.
-
Product
Cable Assembly 68-Pin Micro-D Female to Unterminated, Cut Ends, 0.5m, Spring Latch
40-972A-068-0.5m-FU
Cable Assembly
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by a Metal Spring Latch.
-
Product
High Voltage 37 Pin D-Type Connectors for Pickering Products
-
The connectors below are suitable to use with Pickering cards and modules that utilize a high voltage 37-pin D-type connector.
-
Product
PXI/PXIe Microwave Relay, Dual SPDT, 18 GHz, 50 Ω, SMA, External Termination, Failsafe
42-781A-122
Relay
The 40-781A-122 (PXI) and 42-781A-122 (PXIe) are dual SPDT failsafe 18 GHz microwave relay modules with external terminations. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50 GHz in 50 Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
Product
LXI 50Ω Microwave Transfer Switch
60-808-515-002
-
These LXI (Ethernet-controlled) Microwave Transfer Switches are suitable for routing 50 Ω signals up to 50 GHz. With up to 16 switch banks, they are ideal for constructing complex microwave switching systems for many applications. Connection is by front panel mounted SMA. SMA 2.9 or SMA 2.4 connectors.
-
Product
Accessories
-
From electrical connectors through reflectors, and mechanical mounting systems, SICK offers a comprehensive range of accessories to safeguard the availability of application solutions. Perfectly matched to the corresponding sensors, these accessories provide the basis for cost-effective integration into systems and are available with short lead times.
-
Product
Cable Assembly, 200-Pin LFH, Female (Female Screwlocks) to 4x50-Pin IDC, Male, 1m
40-971B-200-1m-FM
Cable Assembly
This female rear exit to male ribbon 1m long cable assembly does not connect directly to Pickering Interfaces products that use the 200-Pin LFH connector, but customers may find it useful in the development of their own connection solutions. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin male 2.54mm pitch IDC connectors. The 200-pin connector can be secured to its mating connector by female screwlocks.
-
Product
PXI Power Supplies
-
PXI is an abbreviation for PCI eXtensions for Instrumentation. It is based on the PCI architecture, a commonly-used standard in personal computers, with an industrial connector. A second connector adds instrumentation-specific signals to the backplane, like clock and trigger signals. Applicos is providing PXI modules that intend to close a gap in the portfolio of the big players such as National Instruments, Keysight, ADlink and others. We focus on special functions and above average performance. Also in PXI the Applicos culture yields excellence on noise, accuracy and other analog properties.
-
Product
Fiber Optical Switch at Single Mode Latching 1310/1550nm 5V with LC/PC Connector
SUN-FSW-1x2H
-
Guilin GLsun Science and Tech Group Co., LTD
GLSUN 1×2H Mechanical Optical Switch Fiber Switch Features·Low Insertion Loss·Wide Wavelength Range·Low Crosstalk·High Stability, High Reliability·Epoxy-free on Optical Path·Latching and Non-latchingGLSUN 1×2H Mechanical Optical Switch Fiber Switch Applications·R&D in Laboratory·System Monitoring·OADM·MAN (Metropolitan Area Network)·Network Security and MonitoringGLSUN 1×2H Mechanical Optical Switch Fiber Switch SpecificationsParametersUnitSUN-FSW-1×2HWavelength Rangenm1260 ~ 1650Test Wavelengthnm1310 / 1550Insertion Loss 1, 2dBTyp: 0.8 Max: 1.0Return Loss 1, 2dBSM ≥ 50Crosstalk 1dBSM ≥ 55PDLdB≤0.05WDLdB≤0.25RepeatabilitydB≤±0.02Operating VoltageV3.0 or 5.0DurabilityCycles≥ 10 MillionSwitching Timems≤8Optical PowermW≤500Operating Temperature℃-20 ~ +70Storage Temperature℃-40 ~ +85Relative Humidity%5 ~ 95Weightg14Dimensionmm(L )22.5×(W)11.8×(H)10.2 ±0.2Note: 1 Within operating temperature and SOP.2 Excluding Connectors.
-
Product
500-Pin SEARAY Cable Assembly, Male to Male, 2 Amp, 2m, 250 Port
A500RMR-500RMR-5C200
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products using the 500-Pin SEARAY connector. Screwlocks are provided to secure the cable assembly to a mating product.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Single-Mode, 9/125 Fiber, LC Connectors
42-850A-414
Multiplexer Module
The 40/42-850A-414 is a PXI/PXIe 4-channel multiplexer with LC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
Product
PXI Resistor Module Quad 8 Bit
40-291-021
Programmable Resistor Modules
The 40-290 Series Programmable Resistor Modules comprise a Dual 16-bit or Quad 8-bit resistor chain together with 16 optional SPDT Reed Relays. Connections are made via a front panel SCSI 2 type 68 pin male connector. Programmable resistors may be connected together either in series or in parallel to form many types of configuration.
-
Product
SIMRC - 8 x 4 Matrix 1-Pole
1030-R-8-4-1-5/1D
Matrix Switch Module
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
Product
Adapter, 50 Ohm Type-N (f) to 75 Ohm Type-N (m), DC to 3 GHz
11852B
Coax Adapter
The Keysight 11852B is an instrument-grade, 50-ohm type-N female to 75-ohm type-N male adapter. This product is also available in a 50-ohm type-N male to 75-ohm type-N female configuration. The 11852B Option 004 has a 50 Ohm Type-N (m) and 75 Ohm Type-N (f) connector.
-
Product
MAX31855 J-Type Thermocouple Arduino Shield
SEN-30004-J47
-
Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino. The MAX31855J supports a measured temperature range of -210C-1200C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or Mega
-
Product
RF Connectors
MCX Connectors
-
The MCX (Micro Coaxial) series is available with 50 or 75 ohm options, and has broadband capability ranging from DC to 12 GHz. In addition, the MCX series features secure, fast and easy snap-on/ snap-off coupling. MCX connectors were introduced in the 1980s and conform to the European CECC 22220 spec.
-
Product
2-port/4-port PCI Express 1GigE PoE Card with M12 X-
AX92325
-
Four M12 x-coded connectors with special design (to avoid occupying two slots) 2 or 4 independent Gigabit PoE ports, Supports 9.5KB Jumbo Frame and IEEE 1588, Compliant with IEEE802.3at to deliver 30W at 54 VDC per port, PCI Express x4 compliant
-
Product
Quad 4 Fold AND/OR/MAJ, NIM-TTL TTL-NIM Translator
V976
-
The Mod. V976 is a 1-unit VME module housing four 4-input Coincidence Fan in/Fan out and NIM – TTL / TTL – NIM adapter sections. Each section features 4 inputs and 4 outputs on LEMO 00 connectors and can operate as a 4 channel level translator or as AND/OR gate.
-
Product
PXI/PXIe USB Data Comms Multiplexer, 8-Channel
42-737A-901
Multiplexer Module
The 40-737A-901 (PXI) and 42-737A-901 (PXIe) are 8:1 USB multiplexers for switching USB1 and USB2 data and power connections with USB connectors. The data signal paths are 2-pole arranged as differential pairs as defined by the USB standard. The signal pair has a controlled differential impedance and the multiplexer has been designed for minimum insertion loss.
-
Product
Attenuators & Loads
-
*High power handling 100W with a wide range of available attenuation values*Very low PIM <- 160 dBc with excellent return loss performance*Support for 7-16 or 4.3-10 connectors and optional 19 inch rack mount kit*Designed and produced to ISO 9001:2008 certification standards for reliability and quality
-
Product
NI-9264, 25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module
780927-01
Voltage Output Module
25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module - The NI‑9264 is a simultaneously updating analog output module that accommodates higher‑channel‑count systems. Higher density modules conserve chassis space, which leaves room for other measurement types. Each channel has its own digital‑to‑analog converter. The spring-terminal version of the NI‑9264 uses a 36‑position connector for the output channels, and each channel has a ground connection.
-
Product
Single Port RS232 Serial Communications Compact Flash Card With Ruggedized Connector
CF232-R
-
The CF232 is a tiny Type I format Compact Flash (CF+) single RS232 asynchronous serial port for your PDA, laptop (with an optional adapter), or desktop (using one of Elan's Desktop PCMCIA adapters). The card automatically configures to become another COM port by using the built-in O.S. drivers that are tried and tested and are optimized to work in the Windows environment.
-
Product
LXI WTB Extender
60-984-001
-
The 60-894 provides a simple an effective method of joining two LXI WTB bus cables together to extend the length of available cables. It is an ideal solution for cable extension where users need to experiment with different cabling solutions without having to totally replace the cables in the system. The 60-894 provides mating connectors for the WTB on each end connected together by a set of accurate differential transmission lines to avoid additional reflections on the cable. The 60-894 is entirely passive and is compatible with the LXI specification.
-
Product
Edge Connector Fixture
220EDGE
-
An edge connector fixture can be a low cost alternative to a bed of nails fixture. The most important features of this Edge Connector Tester is its portablility, ease of use, intuitive control functions, and durability in a production environment.
-
Product
PXI low-density general purpose switch modules
-
These PXI low-density general purpose switch modules provide cost-effective solutions for applications where a high number of relays is not required. All of these modules use a 96 pin male connector that is supported by our comprehensive range of cable and connector accessories, ensuring they can be quickly integrated into your test system with minimum effort.
-
Product
EN 50155 M12 8GE PoE + 2GE Managed Switch
EKI-9510G-MPW
-
M12 connector with IP67 rugged housing, Complies with EN50155 & EN50121-3-2, Complies with EN45545-2 & EN61373, Supports PoE IEEE802.3af/at, Wide nominal power input range: 24~110VDC; Operating power input range: 16.8~137.5VDC.
