-
Product
Surface Mount Ball & Socket Test Point
SMOX
-
SMOX is a unique select on test terminal which provides accurate line tests in PCB assembly. Supplied loose or on tape and reel for ease of assembly, its unique retention mechanism enhances reliability through low stress contact.
-
Product
Benchtop Automated Functional Test
midUTS
Functional Test
Combining bench-top portability with powerful automated test functionality, the midUTS is an extremely versatile yet cost-effective solution for your electronics functional test needs. Comprised of high-performance commercial-off-the-shelf (COTS) instruments, along with Bloomy’s medium-density signal-routing PCBAs, a built-in or USB-connected PC, and a pair of high-integrity, production-grade cables connected to an adjacent benchtop fixture, the midUTS can be used in engineering for PCBA bring up, as well as scaled to manufacturing to perform high-volume PCBA and sub-assembly functional testing. It is also ideal for depot diagnostic test, debug, and repair of field returns. The two mass-interconnected cables connect the midUTS to as many as 320 test points on the unit under test (UUT), supporting an extreme wide variety of products using bed-of-nails as well as cable-connected UUT test fixtures. Most importantly, the midUTS helps you automate sequences of functional tests using NI TestStand and the Bloomy EFT Module for TestStand. This ideal balance between powerful features and affordable cost allow you to automate earlier in the product development lifecycle, substantially increasing product quality and minimizing time-to-market!
-
Product
Multipurpose Debug Board For EC
DB30 x86 Debug Module
-
The DB30 x86 Debug Card is designed for debugging of COM Express modules with FFC (FlexFoil Cable) debug connector. It includes an 80 port for Power on and Self-test (POST) via I2C interface, interface to SPI Flash for BIOS update, interface to EC for Embedded Controller (EC) update, Power and Reset buttons, and Status LEDs and Test Point for various debug tests.
-
Product
Design for Test
-
Test Coach offers Design for Test (DFT) consulting to assist customers with design review of prototype boards prior to release for production. Design for Test analysis is extremely important in ensuring that an assembly will achieve the highest possible test coverage. For ICT, this DFT will review the board to confirm that the bed-of-nails test fixture can be fabricated to test an assembly without sacrificing test coverage. As with ICT, Flying Probe benefits from DFT analysis by reviewing test point access and mechanical challenges that may affect the potential test coverage. Completing a DFT enables Test Coach to make recommendations to our customers that may be implemented on boards during the design phase which will allow for the most comprehensive coverage at time of test.
-
Product
Reverse Osmosis Meters For Measuring Total Dissolved Solids
RO Meters™
-
The choice of professionals for years, this compact instrument has been designed specifically to demonstrate and test Point of Use (POU) reverse osmosis or distillation systems. By measuring electrical conductivity, it will quickly determine the parts per million/Total Dissolved Solids (ppm/TDS) of any drinking water.
-
Product
SWB-2815, 4x86, 0.3 A, Row Access, Reed Relay Matrix Module for SwitchBlock
781420-15
Reed Relay
4x86, 0.3 A, Row Access, Reed Matrix Module for SwitchBlock - The SWB‑2815 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
Melting Point Testers
-
These melting point testers are designed to accurately test the melting point of medium used in thermometers, for educational purposes, for quality control, automated process and more.
-
Product
Very High Density Fiber Tap
Flex Tap VHD
-
Keysight Network Applications and Security
Flex Tap VHD is a modular, very high density fiber tap available, offering up to 36 taps in a 19 inch 1U space, to reduce IT costs while helping ensure availability of security and business critical applications. Network taps (test access points) are a key part of the access layer of a visibility architecture because they are an unobtrusive way to capture monitoring data. They offer comprehensive traffic visibility for network monitoring and security tools that do not introduce points of failure in the network. Ixia has a large variety of network taps on the market today, offering speeds from 1Gbps to 100Gbps, single and multi-mode, as well as different fiber types and support for Cisco bidirectional (BiDi) transceivers.
-
Product
2 Pole 12 X 4 Low Thermal Relay Matrix Module
DP-cPCI-4113
-
A matrix is the most versatile switch topology. It is made up of rows and columns that connect any input to any output. With matrix switching system, it is easy to connect a number of instruments or sources to various test points of the UUT. The benefit of matrix switching is simplified wiring with which the overall test system can easily and dramatically change the internal connection paths without any manual intervention.DP-cPCI-4113 offers switching matrix in a single slot 6U sized cPCI module with flexibility to configure for 48 cross-points or 72 cross-points on factory selectable basis.
-
Product
Plugbord
3682-2
-
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side)on 0.156"(3.96mm) centers.Interleaved buses pattern on wiring side only solder- coated for user convenience.Bus outline silkscreened on component side to facilitatecomponent placement. Mounts DIPs with 0.3”, 0.4” & 0.9” lead spacing. Unclad test point area at top of board Row and column legends provided
-
Product
Testing Services
-
*Programmable Multipoint Tester*Over 8,000 programmable test points (DWV, Capacitance, Insulation Res., 2/4-Wire Resistance, etc.)*1500VDC / 1000 VAC Dielectric Withstanding Voltage (DWV)/ Hi-Pot (Programmable Dwell times)*Full Electronics laboratory complete with state of the art testing equipment*Custom Unit Testing (Designing of Specialized Test fixtures)*EMI Testing*Temperature and Humidity Testing*Shock Testing*Vibration Testing*Sand and Dust / Altitude Testing*Military Qualification Tests Performed
-
Product
Fixture and Software for Open/Leak Inspection
-
In addition to jigs and fixtures for probing conductors and electrode pads, NIDEC-READ provides specialized software for test point selection and log analysis.
-
Product
Tensile Strength Machine
UI-1100
-
Tensile Strength Machine, also known as Tensile Strength Tester, Universal Testing Machine (UTM), is used to do tensile, peel, shear, bend, and other tests of materials. Universal Testing Machine can do plenty tests like sole/upper bond test ISO 20344, velcro strength test (peel and shear strength) ISO 22776,zipper strength test ASTM D2061, rubber tensile test, 3 point bending test and etc.
-
Product
Multiplexers
-
Capable of performing the necessary switching between test points of the device under test, to give access to low frequency measuring instruments, in electronic test systems based on tool receivers.
-
Product
Test Board For QSFP28 Transceiver
EQSFP28
-
The OPTELLENT EQSFP28 is a cost-effective and convenient test board for testing QSFP28 optical transceivers in R&D and manufacturing environments. The EQSFP28 is equipped with high quality RF connectors for data signals and test points for low frequency control and status signals. The EQSFP28 is equipped with power supplies to enable voltage margining. Key status signals are displayed using LED indicators.
-
Product
Platforms
-
The use of switching systems to route instrumentation and stimulus signals to appropriate test points on a unit under test has a very crucial role to play in most electronics test systems. The sharing of test resources, connection of calibration references, load management, and many other functions are all managed by the switching system, the switching system acts as the interface between the unit under test (UUT) and the test equipment.
-
Product
SWB-2833, 4x71, 2 A, Electromechanical Relay Matrix Module for SwitchBlock
781421-33
Relay Matrix Module
4x71, 2 A, Electromechanical Relay Matrix Module for SwitchBlock - The SWB‑2833 is an electromechanical relay matrix card for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
Mag Lead w/Alligator Clips
138
-
*54" Test Lead Set *Mag Lead features a magnetic disconnect. *You can "stick" to any metallic ground or test point. *Time saving product - can substitute for alligator clips at metallic test points. *Now, when you need alligator clips, you've got them! *Fits almost all DMM's and hand held scopes. *Get the Mag Lead, it stays put and won't fall off!
-
Product
Non-Contact Voltage Detector
VOLTCHEK
-
The VOLTCHEK is a variable non-contact voltage detector, A proximity device which detects the presence of an alternating electric or electromagnetic field. It is used by industry professionals for live or dead voltage determination of outdoor overhead or underground at URD test points. Firstly as a proximity device to determine live or dead situations and then as a touch device to verify the source has physically reached the zero AC field. This is the only equipment capable of testing all voltage from AC 415V to 765kV from a distance, beyond arcing zone.
-
Product
Test Fixture with API
TA-14VG
-
The TA-14VG test fixture is based on the requirements for the Integrated Test Procedure for the VG-14A assembly as shown in the OEM maintenance manual. The panel also contains a test point breakout for the units main connector as well as one for the VG-401 base. The VG-401 breakouts provide an in series connection that will allow easy access to the gyro's signals and also provides a way to monitor rotor current. The panel also contains a variac to allow for line voltage adjustment.
-
Product
Dedicated Testers
-
Dedicated Testers are often inexpensive due to their low test point requirements, which allow for a reduction in switch cards, especially when compared with a Universal Tester. Ease of setup is accomplished through the utilization of transfer connectors between the fixture and the machine. However, this can contribute to a higher fixture cost than typically seen with a Universal Test Fixture due to the nature of their construction which is labor intensive.
-
Product
Cable/Harness Test System with Rack-Mounted Switching
CKT1175-20
-
The CKT1175-20 is a high-voltage wiring analysis system that features rack-mounted switching matrices. This system is expandable in 100 test point increments to 96,000 test points, and available with a wide variety of adapter cable interface connectors, with the standard interface being the CKT MAC interface system.
-
Product
PXI RF Multiplexer Switch Module
RF Multiplexer
PXI RF Multiplexer Switch Modules are ideal for high-channel-count applications that need to connect measurement or signal generation instruments to various test points on devices or units under test(DUTs or UUTs). PXI RF Multiplexer Switch Modules use a variety of relay types, including electromechanical armature relays, reed relays, field-effect transistor(FET) relays, and solid-state relays, each with their own benefits, allowing you to choose a multiplexer that fits your requirements. To program the switches, you can use the IVI-compliant NI-SWITCH driver software, complete with help documentation, example programs, and a soft front panel application for interactive control of switches. For intelligent management of complex switch systems, NISwitch Executive provides additional software tools to help you design, build, and deploy your switching system.
-
Product
PCB Test Points and Terminals
-
Our PCB test points and terminals feature a large loop for easy probe attachment or to facilitate the clipping on of other components. They are ideal for components which need frequent replacement and are also suitable for raising hot components above the surface of the PCB.
-
Product
Switches
-
Whether you are performing high-accuracy, low-speed measurements on a dozen test points or high-channel, high-frequency characterizations of integrated circuits, National Instruments delivers a flexible, modular switching solution based on PXI or SCXI to help you maximize equipment reuse, test throughput, and system scalability.
-
Product
Programmable Hi-Pot Tester
DU331/332/333
-
Delta United Instrument Co., Ltd.
Large LCD Display Window for Setups and Test Values Output Frequency 50/60 HZ SelectableAll Initial Default Function Setting scan be Changed Easily to Fit RequirementEasy Manual Driven with Cursor Guiding Operation Mode Battery Backup Function will Recall theTest Parameter Settings before Power offLarge Memory (100 sets) for Setup Steps & ParametersEach Memory offers 9 steps of different Test ParametersTest mode: Single Step, Multiple Steps (Step by Step), Test Circle Number or Continuous Test are Programmable DU333 is designed for Multi-point Scan Test DU331/DU332 can perform Multi - point Test when used with Scan Box DU330
-
Product
Debug Fixture
-
With at-speed test, debug can easily become a problem: If test points are on the bottom, as is often the case for test processing, then this requires the board to be flip over for the debug. However, during at-speed testing, key devices and signal paths are often on the topside. IST Engineering has in-house expertise with debug fixtures, which allow the test technician to flip over a test board, or even hold it vertically for dual-sided access, while still running the Device-Under-Test at full-speed through card-edge connectors - whether these are standard DIN type or F or N type co-ax connectors. The debug stations are constructed robustly, with metal frames and high-grade flexible cabling and can also be used as backup test stations in a manufacturing flow. They can be built with custom machined waveguide connections for RF/Microwave applications, or with standard, off the shelf connectors, as defined by the application. A number of these debug fixtures are in production use with a range of customers.
-
Product
SWB-2810, 4x43, 1 A, No Row Access, Reed Relay Matrix Module for SwitchBlock
781421-10
Reed Relay
4x43, 1 A, No Row Access, Reed Matrix Module for SwitchBlock - The SWB‑2810 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
Voltage Indicators
-
*Measures voltage from 100V to 138kV line‑to‑line.*Can be used individually as voltage indicators or together for phasing operations up to 100 ft (30 m) apart.*Two LED displays are automatically synchronized during phasing operations.*Clear in-phase and out-of-phase indication.*Versatile for overhead and underground applications.*Capacitive Test Point and Peak Hold modes
-
Product
CAM/TRAC Test Kits
Series 43
-
The GR Series 43 CAM/TRAC®1 kits, utilizing the patented CAM mechanism, offer precise Z axis linear motion when testing higher point count and finer pitch test centers. By using the Z axis motion, side load of the test probes is minimized thus increasing probe life and performance. The Series 43 provides interface compatibility by using a 12 position, GR2270 style I/O block interface. This interface accepts the industry standard I/O, power, and coax blocks.
