-
Product
Battery Probes
Battery Probe
*Charging *Connecting *Docking Station for *Medical- IOT - Communication
-
Product
Probes
-
measures relative pressure range from -1 to 60 bar and -14 to 870 psi and comes with wireless connection low energy.
-
Product
Thermocouple Probes
-
sensor that measures temperature. It consists of two different types of metals, joined together at one end. When the junction of the two metals is heated or cooled, a voltage is created that can be correlated back to the temperature.
-
Product
Probes
Hygro-i Series
-
The Tramex Hygro-i ® relative humidity probe is the most advanced, resilient and reusable RH probe on the market today. Used in conjuntion with Tramex CMEX II and MRH III moisture meters, the Hygro-i ® relative humidity probes allow the user to perform in situ and hood type RH testing to comply with ASTM F2170 and British Standards BS 8201, 8203, 5325 for the Flooring Industry, and is ideal for use by Flood & Water Damage Restoration and Indoor Air Quality professionals.
-
Product
Switch Probes
-
A Switch Probe is a spring contact probe and receptacle combination that is normally open, and after a designated travel the switch probe closes. The most common use for switch probes is in the cable harness testing industry. The switch probe is used to verify the correct location of a terminal in a connector while checking the retention force as well. Switch probes also verify the presence of nonconductive components such as caps for connectors or devices on a circuit board. Smiths Interconnect offers three standard sizes of switch probes.
-
Product
TSP157 Switch Probes
Switch Probe
Current Rating (Amps): 10Average DC Resistance lower than (mOhm): 20Test Center (mil): 157Test Center (mm): 3.99Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 984Overall Length (mm): 25.00Switch Point (mil): 67Switch Point (mm): 1.70
-
Product
Microwave Probes
D-Probe
-
With only two signal pins, D-Probes can perform accurate measurements without the need of nearby ground pads.
-
Product
Socket Probes
-
A lot of companies build test sockets. But only our test sockets are populated with our own proprietary probe technology, developed internally. This assures you that when you purchase one of our test sockets, you are using the most advanced interconnect available.
-
Product
Smart Probes
-
A wide selection of rugged smart probes for your sensing needs. From non-contact IR sensors to a full range of sensor types including Temperature, Humidity, Process, RTD, Thermocouple, pulse, and mor...
-
Product
Active Voltage Probes
-
Engineers must commonly probe high-frequency signals with high signal fidelity. Typical passive probes with high input R and C provide good response at lower frequencies, but inappropriately load the circuit, and distort signals, at higher frequencies. Active voltage probes feature both high input R and low input C to reduce circuit loading across the entire probe/oscilloscope bandwidth. With low circuit loading, and a form factor that allows probing in confined areas, the active voltage probe becomes the everyday probe for all different types of signals and connection points.
-
Product
Digital Inspection Probes
DI-1000
-
The ergonomically designed DI-1000 is Lightel’s all digital video microscope probe. It connects directly to your PC through the computer’s USB2.0 port. Featuring easy single finger focusing, a built-in image freeze/capture button, and detectable resolution to 0.5µm, the DI-1000 package includes our free ConnectorViewTM (standard) software, providing digital zoom, image display, image capture, auto-calibration and basic analysis tools.
-
-
Product
Test Probes
-
Safety right angle insulated alligator test probe, safety right angle insulated alligator test probe with insulated jaws, test probe, minitest probe, micro test probe.
-
Product
Accessories, Styli & Probes
-
Pratt & Whitney Measurement Systems, Inc.
A Standard to Grow With
-
Product
IsoVu Isolated Probes
-
The IsoVu Measurement Systems can make nearly impossible measurements – like high-side Vgs- a reality, providing today’s power engineer with measurement insights not available in other power systems and instruments. When performing near-impossible measurements, especially in those involving Gallium Nitride (GaN) and Silicon Carbide (SiC), it can be extremely time consuming and cumbersome. IsoVu eliminates those concerns: IsoVu probes offer better common mode rejection and higher bandwidth for high EMI environments and on power FETs like SiC and GaN.
-
-
Product
USB Hall Probes
-
MAGNET-PHYSIK Dr. Steingroever GmbH
The USB Hall probe is simply connected to a computer and operated using easy-to-understand software. No additional measuring device is required to measure the magnetic field strength. You can download the "USB Teslameter" software for Windows here. A Linux version is available from us on request.
-
Product
Flexible Magnetic Field Probes
-
Projekt Elektronik Mess- und Regelungstechnik GmbH
The active probes are equipped with active amplifier electronics and have an extremely low-impedance output, ie they can also drive long lines. The output signal is calibrated according to specification. They can not only be connected to a certain type of teslameter, but can also be connected to any signal input.
-
Product
Transmission Line Probes
-
Transmission line probes are a special type of passive probe designed for use at very high frequencies. They replace the high impedance probe cable found in a traditional passive probe with a precision transmission line, with a characteristic impedance that matches the oscilloscope input (50 Ohm). This greatly reduces the input capacitance to a fraction of a picofarad, minimizing the loading of high frequency signals. A matching network at the tip increases the DC input resistance. While they have lower DC input resistance than a traditional passive probe (usually 500 Ohm) to 1kOhm), the input impedance of these probes remains nearly constant over their entire frequency range. A traditional /10 passive probe will have a 10 MOhm) input impedance at DC, however this impedance drops rapidly with frequency, passing below the input impedance of a transmission line probe at less than 100 MHz.
-
Product
Probes Dissolved Oxygen
-
Specialized, in-line sensors that provide real-time, continuous monitoring of oxygen levels in liquid.
-
Product
Sanitary Probes
-
Used in the food, beverage, dairy, and pharmaceutical industries, these hygienic/sanitary probes carry 3-A certification, which is required in these sanitary, wash down, & clean-in-place applications.
-
Product
Probes With Industrial Heads
-
Used in industrial applications for process temperature measurement, these probes come in a variety of protection head styles for easy connection wiring to your extension cable
-
Product
Other Passive Probes
-
Probes connect the input of the oscilloscope to test points on the device under test (DUT). There are many types, including: high impedance passive, low capacitance, single-ended active, differential active, high voltage, and current probes. This is the first in a series of three articles on probe selection and application, and will focus on passive probes. Part 2 and part 3 will address active probes and current probes, respectively.
-
Product
Differential Probes (8-30 GHz)
-
The DH series of 8 to 30 GHz active differential probes provides high input dynamic range, large offset capability, low loading and excellent signal fidelity with a range of connection options.
-
-
Product
BTP-25 Bead Probes
Bead Target Probe
Current Rating (Amps): 8Average Probe Resistance (mOhm): 8Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cyles): 500,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
General Purpose Probes
General Purpose Probe
*High current*Fine pitch*Long travel*Mounting options
-
Product
Probes
Type K
-
No matter the application, ThermoWorks has a probe for you: penetration probes, immersion probes, air probes, surface probes, wire probes, even specialized probes like griddle probes, burger probes, pipe clamp probes, and probes for medical and lab use. Choose from standard tip, reduced tip, corkscrew tip, alligator clip, or needle probes; different handle types; and straight, coiled, stainless overbraid or even armored cables. Sensor types include type T or type K thermocouples, RTD sensors and our Pro-Series® line of thermistor probes.
-
Product
Fine Pitch Probes FP800D2901B050G025L057
1130428
-
The Fine Pitch Probes FP800D2901B050G025L057 are engineered for precision applications requiring outstanding reliability and performance across various temperature ranges. Designed within the FP-D family, these double plunger probes are optimal for tight pitch applications, featuring a pitch measurement of 1.00 mm / 39 mils, and are capable of operating effectively from -45°C to +200°C. Their compact design, with an overall length of 5.70 mm and a projection height of just 1.10 mm, makes them suitable for use in high-density electronic assemblies where space is a critical factor.In terms of electrical performance, the FP800D2901B050G025L057 probes can handle a continuous current of up to 3.50 A, while maintaining a minimal typical contact resistance of 55 mOhm. Moreover, they are designed to perform at frequencies of up to 7.10 GHz, ensuring high-speed data integrity for demanding applications. Mechanically, these probes exhibit a preload of 10.00 cN with a maximum travel capability of 0.85 mm, ensuring optimal contact while minimizing wear. Crafted from high-quality materials, the probes feature beryllium copper plungers with gold plating, ensuring both excellent conductivity and resistance to corrosion, thereby enhancing their lifespan and reliability in various environments.
-
Product
BARE BOARD TEST PROBES
-
Probe Technical DataMechanicalMINIMUM CENTERS: .100 (2.54)FULL TRAVEL: .160 (4.06)WORKING TRAVEL: .107 (2.72)OPERATING LIFE: 1,000,000 cyclesElectricalMAXIMUM CURRENT: 5 amps continuousat working travel, non-inductiveRESISTANCE: At 35 mA test current60 18 mOHMS mean63 60 mOHMS meanMaterials and FinishesPLUNGER: Heat treated beryllium copper60 24 Kt gold plated over nickel63 24 Kt gold plated over nickelBARREL: Nickel silver60 24 Kt gold plated ID and OD over nickel63 No FinishSPRING: Music Wire, 24 Kt gold platedover nickel
