Connectors
dock multiple contact or data junctions.
See Also: Interconnects, Mass Interconnect, Cable Assemblies, Contacts, Harness, Wire, Test Point, Cable Assembly
-
Product
Cable and Antenna Analyzer
iVA-0627A-NC
-
iVA Cable & Antenna Analyzer System, Type N male connector with Neoprene Soft Case
-
Product
Coax, Contact, Receiver and ITA, 40 GHz
610102114
-
The 40 GHz Coax contact is a blind mate connector that mates with 3.5 mm and 2.92 mm connectors. It is recommended to use 2.92 mm connectors for frequencies above 35 GHz.
-
Product
160-Pin DIN41612 Connector, Crimp Pin, Female Contact
40-960A-160-FCP
-
Female crimp contact for 160-pin DIN41612 connector, pack of 80 contacts.
-
Product
Fracture Mechanics Clip-On Gages
Model 3541
-
Jinan Testing Equipment IE Corporation
The Model 3541 is designed for determination of fracture mechanics parameters such as JIC, KIC, R-curve, fatigue crack growth rate (da/dN), and testing to standards such as E1820, E399, E647, etc. These COD gages conform to the requirements of E1820 (the replacement for E813 and E1737) for JIC and R-curve determination. Special configurations are available to meet the requirements of ASTM E399 for fracture toughness (please consult the factory for these configurations). In addition, the modified groove design complies with E1820 tests where greater stability and accuracy results from the sharper groove root. Clip-on gages are used for a variety of fracture mechanics tests, including compact tension, arc shaped, disk shaped, bend specimens or other specimen geometries in compliance with ASTM and other standards organization’s test methods. Clip-on gages can be used directly on test specimens where the knife edges are integral with the test specimen or, alternately, with optional bolt-on knife edges mounted on the test specimen.The Model 3541 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
PXI 2A Multiplexer, 1-Bank, 64-Channel 2-Pole
40-614-016
-
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Ferrules, 1m
A050DM5-F-0A100
-
The 50-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
20-Pin GMCT Cable, Female to Unterminated, Cut Ends, 10A, 3m
A020GFR-C-0C300
-
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation. Users may need to make their own cable strain relief arrangements when using this product and should ensure appropriate electrical safety precautions are observed.
-
Product
4 Pin Power D-Type Female Connector, 40A, PCB Mount
40-963-004-RF
-
This connector is suitable for Pickering Interface's modules that use the 4-Pin Power D-Type connector. It is designed to allow users to make a termination via a PCB.
-
Product
20-Pin GMCT Cable, Male To Unterminated, Tinned Ends, 16A, 2m
A020GMR-T-1B200
-
The 16A 20-Pin GMCT cable assembly is constructed from 19/0.41 (14AWG) Copper Wire with PFA 500V insulation. Screwlocks are provided to secure the connector to associated product.
-
Product
90 Degree Hybrid Couplers To 500 MHz
-
Hybrid couplers with bandwidths as broad as 125:1 are available for applications within 100 kHz to 500 MHz. Power handling is 1 watt maximum for a load VSWR of 1.2:1 or better. These hybrids have an isolation of 20 dB and phase balance of 3 degrees. Most models have a VSWR of 1.4:1 or better throughout their operating bandwidths.Pulsar Microwave currently offers these hybrid couplers packaged in three outlines, including an SMT version. Standard offering of connectorized packages 412 and 442 are with SMA female connectors. Outline 412 may be customized with any combination of BNC, TNC, F or N connectors. Outline E is the surface mount version and requires less than one square inch of board area, making it well-suited for portable applications.
-
Product
Cable 96-Pin Female to 100-Pin Male Micro-D, 2m
40-973B-096-2m-FM
-
The 96-Pin to 100-Pin SCSI Style Micro-D Adaptor Lead is constructed from 7/36 (28AWG) Tinned Copper twisted pair wiring with Polyolefin insulation to minimise crosstalk. Metal Spring Latches are provided on the 96-Pin connector and 4-40 UNC screwlocks on the 100-Pin connector.
-
Product
LXI 50Ω Microwave Transfer Switch
60-808-210-012
-
These LXI (Ethernet-controlled) Microwave Transfer Switches are suitable for routing 50 Ω signals up to 50 GHz. With up to 16 switch banks, they are ideal for constructing complex microwave switching systems for many applications. Connection is by front panel mounted SMA. SMA 2.9 or SMA 2.4 connectors.
-
Product
Transceiver Driver
S-112
-
Transceiver Driver slot module of FOTS system is an efficient module for the characterization of SFP type transceiver and the test of optical line or components. This module is a kind of Small Form Factor Pluggable(SFP) host board that can be used to test SFP transceiver modules to define the modules’ performance. The transceiver driver slot has two SFP cage and 20-pin SFP connector sets to mount and control two SFP transceivers simultaneously.
-
Product
8-Pin Power D-Type Cable, Male to Female, 2m
40-970-408-2m-MF
-
The 8-Pin Power D-Type cable assembly is constructed from 56/0.3 (12AWG) Copper Wire with PVC insulation. Screwlocks are provided to secure the connectors to their associated products.
-
Product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Tinned Ends
A050DF5-T-0A100
-
The 50-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
Economy Mechanical Calibration Kit, DC To 6 GHz, 7 Mm
85031B
-
The Keysight 85031B calibration kit contains a set of precision 7 mm fixed terminations and a one-piece open/short circuit used to calibrate Keysight network analyzers for measurement of devices with precision 7 mm connectors. This kit is specified from dc to 6 GHz.
-
Product
CB-50LP Low-Cost, Unshielded I/O Connector Block
777101-01
-
50-Pin Male IDA to 50-Pin, Female Screw Terminal, Panel Mount Terminal Block - The CB-50LP provides 50 screw terminals for connection to I/O signals from 50-pin NI data acquisition devices. The CB-50LP includes one 50-pin header for direct connection to 50-pin cables and metal standoffs for use on a desktop or for mounting on a custom panel.
-
Product
LXI 50Ω Microwave Transfer Switch
60-808-315-003
-
These LXI (Ethernet-controlled) Microwave Transfer Switches are suitable for routing 50 Ω signals up to 50 GHz. With up to 16 switch banks, they are ideal for constructing complex microwave switching systems for many applications. Connection is by front panel mounted SMA. SMA 2.9 or SMA 2.4 connectors.
-
Product
6 Pin Round Pin Tester / Maintenance Kit
#8027
-
Innovative Products of America
Test, clean and restore 6 round pin trailer connections. Included tester will verify tow vehicle is sending proper signal to the connector, while cleaning tools remove corrosion and verify proper pin size on both male and female truck/trailer plugs. For use with 6 round connectors. Quickly tests, cleans and repairs truck and trailer connectors Extends harness life Great preventative maintenance tool Promotes safety and limits road hazardsPatentedKit Includes: #7897: 6 Pin Round Pin Tester, #8022: 6 Round Connector Cleaners, and #8030: 2 ml DeoxIT Cleaner
-
Product
Benchtops
-
Lightel's benchtop scopes use a USB connection to Windows®-based PCs and tablets to view and save clear detailed images of connector endfaces. Our benchtops provide cost effective innovative solutions for inspecting connectors where standard Fields of View may not be adequate. Each benchtop scope comes with easy to use software designed to take best advantage of that scope's capabilities.
-
-
Product
LXI Video Matrices
-
Pickering's LXI Video matrices are suitable for switching frequencies up to 25MHz. They have a characteristic impedance of 75 with the option of mini SMB or MCX connectors, or with a larger case size BNC connectors. Designed to provide a simple and scalable bidirectional matrix for video frequencies and is intended for the easy construction of high-performance bidirectional matrix switching systems.
-
Product
Automotive Test Lead Kit
143
-
Test Lead Kit includes our basic set of interchangeable specialty test probes designed for automotive use. The flexible back probing pins are great for sliding into automotive connectors like those on fuel injectors and MAP sensors. The large Crocodile Clips are good for clipping to grounds and battery terminals. Roll up storage pouch keeps your leads organized.
-
Product
PXI/PXIe MEMS Optical Switch, Dual Insert/Bypass, Single-Mode, 9/125 Fiber, SC/PC Connectors, With Interlock
42-860A-222-HI
-
The 40/42-860A-222-HI is a PXI/PXIe dual insert/bypass switch with SC/PC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
Product
Picolo Pro 2
-
4x BNC connectors on the bracket32-bit 33 MHz PCI busOne video decoder, 25/30 images per second (50/60 fields per second)Fast switching between up to 4 camerasPCI and PCIe versions available
-
Product
PXI 64x4 Matrix Module, 2-Pole, 2A, 60W
40-583-001
-
The 40-583 is a 256 crosspoint PXI matrix with dual pole switching. The module consists of a 64x4 matrix of 2-pole electro-mechanical relays with 2A current handling. The module is designed for switching medium voltage and power signals, typical applications include signal routing in ATE and data acquisition systems. The user signal connection is via a robust 160 pin DIN 41612 connector that is fully supported by the wide range of Pickering Interfaces cable and connector accessories.
-
Product
Cable Assy 68-Pin SCSI Micro-D M/F 2m
40-970-068-2m-MF
-
The 68-Pin SCSI Style Micro-D Cable Assembly is constructed from 7/36 (28AWG) Copper Wire with Polypropylene insulation. Metal Spring Latches are provided to secure the connectors to their associated products.
-
Product
Cable 96-Pin Micro-D Female to Female, 0.5m
40-970B-096-0.5m-FF
-
The 96-Pin SCSI Style Micro-D Cable Assembly is constructed from 7/36 (28AWG) Tinned Copper twisted pair wiring with Polyolefin insulation to minimise crosstalk. Metal Spring Latches are provided to secure the connectors to their associated products.
-
Product
LXI Microwave Multiplexer, SP6T, 14-Bank, 67GHz, 50Ω, SMA-1.85
60-800-814
-
Our 60-800-814 is a 14 bank SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 67GHz. The 60-800 range is capable of supporting up to 16 banks of 6 channel multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
Mini Back Probes/Wire Piercers
618
-
*Great for backprobing weather pack style connectors used with numerous automotive sensors *Also very handy for piercing and tapping readings on smaller gauge wires - using the included probe adapters *Works with most Test Lead Kits in the field - with standard 4mm banana plug test lead *Set includes four probes - red, black, green, yellow Test probes 21 mm length
