Tracking
-
Product
Order Tracking Analysis
-
Order Tracking is a general term describing a collection of measurement functions used for analyzing the dynamic behavior of rotating or reciprocating machinery for which the rotational speed can change over time.
-
Product
TTC-1 Tracking Test Chamber
TTC-1
-
It is according to IEC60695 and IEC60112 (GB4207), the Tracking Test Chamber TTC-1 is intended for determining the degree of protection against formation of conducting paths in solid insulating materials, due to the electric stress and electrolytic contamination of the surface. This method simulates tracking currents on insulation material by providing drops between electrodes. During the process of normal use, insulating material may be exposed to moisture and dirt, if conductive, may cause stress and fire hazard.
-
Product
RF Tracking Generators
-
Using a Spectrum Analyzer (SA) in combination with a Tracking Generator (TG) enables swept scalar frequency response measurements of active and passive networks.
-
Product
Tracking Analysis Software
DS-0322
-
This software enables tracking analysis with high-speed (calculation speed: approx. at 20ms/4-ch), high-resolution (1000 blocks max.) and high-accuracy (more than 100dB dynamic range). It can plot rotation-tracking diagram during calculation, and also can set and plot the diagram of intended order or frequency after the calculation. *DS-0321 series FFT analysis software is required.
-
Product
Proof Tracking Testing Device
-
Shenzhen Autostrong Instrument Co., Ltd.
This Proof Tracking Test Device is a fully automatic instrument contained in its own cabinet to maximize the safety of the operator and mainly used test the resistance Tracking Performance of solid electrical insulation materials when they are exposing in electric affect impurity water situation.Mainly used for determination PTI and CTI items.
-
Product
Subsea Pipe Tracking System
HydroPACT 660E
-
With HydroPACT 660E Teledyne Marine brings the world’s smallest submarine, pulse induction pipe tracker to market. Built upon the already established, industry standard and world leading TSS HydroPACT 440 system, the HydroPACT 660E continues the legacy by bringing pipe tracking and UXO detection capabilities to small inspection and observation class ROVs, for applications that were previously only available on larger vehicles such as work class ROVs and trenchers.The HydroPACT 660E has a single 24 Vdc, small subsea electronic pod, dramatically reducing the installed footprint and payload of the system while maintaining an operating range of greater than 85% of that of the significantly larger HydroPACT 440 system. The coil array features an integrated cable for even greater reliability and is suitable for installation and operation on smaller Observation class ROVs.
-
Product
Multi-Laser Nanoparticle Tracking Analysis (NTA)
ViewSizer 3000
-
Exosomes, viruses, and nanoparticles all have wide size distributions which defeat traditional Nanoparticle Tracking Analysis (NTA) analyzers. The ViewSizer 3000 features simultaneous measurement with three lasers to collect the most accurate distribution and concentration information over a wide range of sizes within the same sample. Where the signal from a particle is too bright and saturates the detector from one laser, the software automatically uses data from a lower power laser to ensure the most accurate size and concentration information. On the other hand, when scattering from one laser is too weak for detection, the software uses data from a higher power laser to accurately track the particle.
-
Product
Dual Channel Multi-Band FM Tracking/Data Receiver In Modular Style Housing
LS-27-B
-
The Lumistar LS-27-B Modular Dual Channel Tri-Band Tracking and Data Receiver is Lumistar’s third generation of modular high performance FM Receivers. This wideband designs supports one or two independent channels of PCM with data rates up to 20Mbps. The unit includes both an optional FM demodulated output for PCM data, and standard programmable AM/linear AGC outputs for auto-tracking receivers. The design offers 8 IF Bandwidths and 8 Video Filters per channel for each receiver.AC coupling with a low pass filter is employed to ensure a high quality data link with long strings of NRZ-L ones or zeroes. The unit provides a software selectable 10 MHz reference I/O port forlocking local oscillators to a high precision external source or to arrange multiple units in a master/slave arrangement. The receiver’s control and status is achieved via Ethernet, USB or auto-switched RS-232 (or “4-wire” RS-485 in place of 232). When utilizing the RS-422 interface, multi-drop configurations can be accommodated.
-
Product
EM Tracking Products
-
The strength of the Aurora and 3D Guidance electromagnetic tracking solutions lies in their similarities and their differences. Both can provide unobstructed in-vivo tracking of OEM medical instruments, share exceptional measurement accuracy and reliability and are engineered and manufactured to deliver unparalleled tracking performance. Between them, there are seven different field generators with unique measurement volumes, and 20 standard sensor offerings (plus custom options). While the Aurora has 6DOF and 5DOF sensors, the 3D Guidance solution specializes in 6DOF tracking. 6DOF sensors are usually re-processable; 5DOF can be disposable. Some of our field generators are portable, while others seamlessly integrate into the medical OEM’s procedural cart or operative table. These differences provide near-countless opportunities to customize and integrate the Aurora and 3D Guidance solutions – all while benefiting from a shared foundation of technical excellence and expert product execution.
-
Product
Tracking Generator
TG44A
-
The Signal Hound USB-TG44A is a 10 Hz to 4.4 GHz tracking generator which works with your USB-SA44(B) to measure filters, attenuators, amplifiers and more! It is compact, simple to use, and an effective troubleshooting tool for general lab use, engineering students, ham radio enthusiasts, and electronics hobbyists.
-
Product
Multi-Band Dual-Channel Receiver/Combiner, 4U Rack Mount System with Integral Tracking Receivers and Bit Syncs
LS-28-DRS Series
-
Lumistar offers the LS-28 series of high performance multi-band multi-mode RF Receiver/Combiners in several different versions including rack mount, portable and modular formats. Complete solutions from RF to bits and/or RF to UDP data broadcast in Chapter 10 format are available. Available at any frequency range from 215 MHz to 6000 MHz, data rates to 50 Mbps.
-
Product
Tracking Index Test Apparatus
CX-L19
-
Shenzhen Chuangxin Instruments Co., Ltd.
It applied with rectangle size of platinum electrode, each electrode can force to the sample is 1.0±0.05N. Electrode Distance: 4.0mm±0.01mm, included angle: 60°±5°. Electrode Voltage: 100~600V, (48~60HZ) adjustable, when the short-circuit current at 1.0±0.1A, the voltage goes down less than 10%. The liquid drop device can make the liquid height from 30~40mm (adjustable), drops liquid size is 44~55 drops/1cm3. The interval drops of liquid is 30s±5s (adjustable). During the testing, the short-circuit current is more than 0.5A to keep 2 seconds, then shut off current, it show the sample not pass. Inside dimension: 0.5CBM and outside dimension: 630mm*390mm*750mm.
-
Product
Multi-Band Dual-Channel Receiver/Combiner, Modular Unit with Integral Tracking Receivers and Bit Syncs
LS-28-DRSM Series
-
Lumistar offers the LS-28 series of high performance multi-band multi-mode RF Receiver/Combiners in several different versions including rack mount, portable and modular formats. Complete solutions from RF to bits and/or RF to UDP data broadcast in Chapter 10 format are available. Available at any frequency range from 215 MHz to 6000 MHz, data rates to 50 Mbps.
-
Product
Telemetry Tracking and Command
TT&C
-
L3 Cincinnati Electronics (L3 CE) offers a variety of TT&C Receivers and Transmitters for various mission requirements. L3 CE can customize any of the products listed below to fit any mission command and telemetry needs.
-
Product
RF Telemetry Receivers, Tracking Receivers, Down Converters
-
Lumistar offers single PCI slot multi-band FM receivers. The same product in a “drive Bay” configuration is available. All Lumistar FM receivers can come without the FM demodulator use as antenna tracking receivers or for use as down converters used with an IF receiver for multi-mode digital combining and demodulation. Dual channel versions are also available.
-
Product
Resistance Wire Bonding
-
Electronic Systems of Wisconsin, Inc.
ESW's Resistance Wire Bonding System comes equipped with the latest features the market has to offer. Our system is capable of bonding armatures, stators or coils. The on-screen display in our bonder makes it easy to read, track, and record your bonding data. If desired, ESW offers complete electrical testing of the part prior to the bonding sequence as well. This ensures only good parts that have been electrically tested are processed through bonding. It is our duty to make sure you never have to worry about losing important information again. Our Sales and Engineering staff will work closely with you to make sure that a bonding systems will meet your needs. See the slideshow below to see some of our Resistance Wire Bonding Testers.
-
Product
Continuity of Insulation Tester (High Voltage Method)
ZGQ-16B
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.5-2008/IEC60851-5;Inspection standard: JB/T4279.13-2008Meet GB/T6109-2008 standard requirementsUsed to test the Insulation continuity (namely the pinhole number of enameled wire sample per unit length) of enameled round wires with nominal conductor diameter ranging from0.05mmto1.60mm;8 level test voltages can be selected by pressing button: 350V, 500V, 750V, 1000V, 1500V, 2000V, 2500V and 3000V;Test length ranging 0～99m;Application of SCM control.Automatically complete test process, display wire testing length and pinhole number;Brushless driving motor, guide pulley and take up pulley are equipotent.The electrode insulation to ground, using high resistance material of non-hygroscopic, no leakage, no tracking, easy to clean, Insulation thickness can ensure long-term 3000V voltage effect.Circuit board is subject to anti-static and moistureproof and long-time aging treatment, has more stable quality and higher durability;
-
Product
Antenna
-
The multifunctional antennas are designed to meet the harsh environmental conditions and limited space availability found on submarines. This is achieved by utilizing a unique stack array enclosed within a protecting fibre glass dome.The antenna characteristics has been developed in such a way so that aircrafts can also operate in the airspace for data and voice communications next to ship-to-ship or ship-to-shore communications. In this way aircrafts e.g. AWACS act as relay stations to transfer radio signals. Although the dipole of the lizard has a primarily plane oriented radiation characteristic – up until an elevation angle of 60 degrees-, submarines can still track aircrafts up to an elevation angle of 90 degree. This guarantees complete coverage of the surrounding airspace in 360 degree horizontal level as well as in 180 degree vertical level.With this outstanding multifunction antenna capability Aeromaritime significantly extends the military communications for submarines by offering this unique capability.
-
Product
Subsea Pipe and Cable Detection & Tracking System
HydroPACT Dualtrack
-
Dualtrack is the combination of the 440 and the 350 systems to provide the ultimate subsea detection system, capable of tracking and surveying pipes and cables via ROV deployment.It utilizes the same industry standard pulse induction technology as the 440 system to survey accurately regardless of vehicle heading. The accompanying display and control software is Windowsâ„¢ based providing a familiarity factor that a specifically built interface would not.
-
Product
Selective Level Meter
Model SLM620
-
- Digital Synthesized Local Oscillator- Two Selective Bandwidths : 20Hz, 3.1KHz- Wideband, Low Noise and Low Distortion Measurements- dB/dBm Operation- High Frequency Stability- Internal Calibration Facility- Recorder Outputs- Frequency Tracking Facility with Level Oscillator SLG620- Storage of Nine Spot Frequencies- Reference Level Set Facility- Autotune Feature- Operates on AC Mains or Internal Rechargeable Battery- Built in charger- Graphic LCD Display with Backlight
-
Product
Insight Product Co. Computer Vision For Object Recognition And Object Segmentation
-
Insight Product Company has developed an automated control system for monitoring the popullation of Siberian tigers and tracking their motions.
-
Product
Threat Warning
-
Long-range, multi-threat capabilities provide continuous tracking while search and verification of surface-to-air and air-to-air missile launches for unsurpassed survivability.
-
Product
Short-Range Perimeter Surveillance Radar
Ranger® R1
-
The Ranger® R1 is a ground-based perimeter surveillance and tracking radar that accurately detects personnel and vehicles at a range of up to 700 m. It scans a full 360° every second, covering up to 1.5 square km (0.6 square miles). Additional units — such as a mid-range Ranger® R2 — can be networked in an overlapping array to protect larger areas, stitching together an impassable radar area outside and inside your perimeter.
-
Product
Trackside Equipment
-
The Automotive assembly track lineside environment requires numerous amounts of tooling & equipment to ensure build phases are completed productively. Jackmark Engineering provides a wide variety of custom designed trackside jigs & fixtures, test leads and assembly aids including validation tooling to various assembly departments from HVAC to end of line.
-
Product
Stand Alone Wafer Sorter
MicroSORT
-
The Microtronic MicroSORT semiconductor wafer sorter is designed to maximize throughput while minimizing wafer handling in a user-friendly operating environment. This stand-alone semiconductor wafer sorter enables sophisticated semiconductor wafer sorter routines for up to 4 wafer-cassette platforms. MicroSORT semiconductor wafer sorter reads OCR scribes from the top, bottom, or simultaneously, allowing for enhanced semiconductor wafer tracking and sorting. The MicroSORT semiconductor wafer sorter’s basic functions include the ability to move, compress, randomize, find, align, verify, and split semiconductor wafer lots. With our virtual tweezer mode, an operator can click on wafer icons to move wafers between cassettes, read semiconductor wafers, and swap wafer positions.
-
Product
Bus Analyzer, Exerciser, Emulator, and Programmer
CAS-1000-I2C/E
-
While the I²C interface seems simple on the surface, this straightforward architecture is not immune to intermittent glitches, device misbehaviors, and protocol violations. Likewise, tracking down these errors can be tedious business if the right tool is not utilized.The CAS-1000-I2C/E bus analyzer is an exceptional tool for pinpointing I2c irregularities. The ability to spot complex problems and identify invisible obstacles make it the preferred I²C development solution. Advanced logging, debugging, emulation, and verification capabilities offer power and versatility, yet the Windows-based user interface makes the most complex features simple to use.The CAS-1000-I2C/E succeeds where simple monitoring and interactive I/O tools fall short—a complete solution to monitoring, emulating, stressing, and characterizing I²C and SMBus interfaces.
-
Product
Thermal Imaging
JOHO307
-
Wuhan JOHO Technology Co., Ltd
JOHO307 thermal imaging binocular is available to work at day and night at any harsh environment for solider excuting combat surveillance, target seraching, tracking and monitoring and other mission
-
Product
Stator & Coil Testing
-
Electronic Systems of Wisconsin, Inc.
ESW Stator Test Systems come fully equipped with the latest industry features. The on-screen display in our testers allows the operator to visually see the part lead hook-up to the tooling connections. Our software makes it easier to read, track, and record your stator test information. While performing tests, you can watch the testing throughout the process in real time. You can view various wave-forms for surge or magnetic field, which can be displayed real-time and printed if desired. The software logs all test results, so that you do not have to worry about losing important information. ESW designs the tooling to be simple to connect the part. We work closely with you to define and implement your customized testing needs. The videos and slideshow below show some of our Stator Testers.
-
Product
Lab Workflow Management Software
-
Use Agilent workflow management software to quickly integrate software systems, track sample state and disposition, or optimize lab processes. Avoid long implementation projects with capabilities tailored to your most immediate needs.
-
Product
Long-Travel Extensometer For Soft Materials
DSES-1000
-
A Long-Travel Extensometer That Is Now Easier to Use and Even More Precise The DSES-1000 is a long-travel contact-type extensometer able to measure displacement up to the breakpoint in tensile tests of rubber and other soft materials. The upper and lower arms are clamped to respective gauge positions using a simple single operation, with each arm tracking sample elongation independently.
