Custom Fixtures
-
product
Test Fixture (SMD Components)
16034E
Perform impedance evaluation on a minimum SMD size of 1.6(L) x 0.8(W) [mm]
-
product
Fixture Self-Test Controller and Calibration Check
AQ818
The module AQ818 includes all the electronic blocks required to perform an effective test platform self-test. Thanks to this module, a chain of tests can be performed, which will end up not only with a report of the defective instruments or switch modules, but also with the relay contacts live expectancy report.
-
product
Functional Test Fixtures
Reliable connections to device under test (DUT) test points are essential for robust functional test. Bloomy provides rugged fixtures and cable sets (ITAs) built for thousands and thousands of cycles in manufacturing environments. With the industry’s best mass interconnects and internal electronic keying, our fixtures are easy to change out and are automatically recognized by the test system.
-
product
Magnetic Material Test Fixture
16454A
The 16454A is designed for accurate permeability measurements of toroidal-shaped magnetic materials. Since the construction of this fixture creates one turn around the toroid (with no magnetic flux leakage), the need of winding a wire around the toroid is unnecessary. Complex permeability is calculated from the inductance with and without the toroid. When the E4991A/4291B with option 002 is used as the measurement instrument, direct readouts of complex permeability are possible. In addition, it is furnished with a small and a large fixture to adapt to a wide range of sizes.
-
product
ATE Self Test Fixtures
AL663
AL663 fixtures include all the electronic parts required to perform an effective test platform diagnostic. The AQ818 device allows to perform a series of tests, obtaining a report of the faulty instruments or switch modules and also a report about the relay contacts estimated life.
-
product
Parallel Electrode SMD Test Fixture
16192A
The 16192A test fixture is designed for impedance evaluations of side electrode SMD components. The minimum SMD size that this fixture is adapted to evaluate is 1(L)[mm].
-
product
Customized Test Fixtures
Test fixture is a device designed to mount a device under test (DUT), equipment under test (EUT) and unit under test (UUT) in place and allow it to be tested by being subjected to controlled electronic test signals and procedures.
-
product
Testing Aircraft Tachometers
The test bench is comprised of a TMB 304 Torque Transducer and a custom fixture for the tachometer and corresponding inertia wheel. A servo motor is incorporated to provide speed to the tachometer. The entire drive train is conveniently mounted on a base plate with the appropriate couplings, bearing support and flywheel.
-
product
VITA 62, 3U Test Fixture
TF-3U-7B041-1
This Power Supply test fixture is being proposed as a tool for checking Injector / Ejector operation, proper alignment of the VITA 62 connector and proper alignment of both keys on a Single slot, 3U, VITA 62/SOSA power supply.
-
product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196C
The 16196C surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results - reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement - now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
product
Custom Products
As your partner for motion control, we offer solutions including customization, engineering and support. So, when it comes to your requirements, don’t settle. Get precisely what you need.
-
product
Magnetizing Fixtures
Usually, the magnetizing fixture (coil) is specifically designed for the task of the customer and the product.In the simplest case, only the necessary parameters for the dimensions of the component are calculated for an axial coil, and the device can be designed and manufactured according to standard procedures.
-
-
product
Test Fixtures
Pneumatically actuated Kelvin connection to custom manufactured device inserts either to complement ART's wide range of precision parametric test equipment or for use with third party measurement hardware.
-
product
Custom Design
RCF professional woofers stand for ultimate performance, highest power handling, and the most advanced technology in the market.
-
product
Custom Test Stands
Our test stands and systems are manufactured to support hydraulic, fuel, pneumatic, and electro-mechanical components.
-
product
Datapaq Customized Systems
Designed to provide the benefits of temperature profiling in unique heat treatment processes, these systems enable users to get reliable and accurate temperature profiles and from inside of the oven.
-
product
Fixture Kit
MF500
Electronic Test Fixture Kit Very low-cost kit facilitates use in situations where traditional fixtures are too expensive:o Research & Developmento Engineeringo Low-volume Production Uses include:o Debuggingo Programmingo Verification and Test
-
product
ICT/FCT-Fixtures
We offer a wide range of testing fixtures. In Circuit Test fixtures, Functional Circuit Test fixtures, small and simple fixtures up to large special designed testing solutions.
-
product
Food Grips and Fixtures
AMETEK Sensors, Test & Calibration
We supply material testing instruments to some of the world’s most innovative companies within the food industry. The reason for this is our extensive experience within food testing, combined with our high precision texture analysis and packaging test systems.
-
product
Custom Engineering Services
Ironwood Electronics has the largest, most experienced engineering staff in our industry. Quick turn custom solutions are our specialty, with some custom solutions available as fast as 1 week. Our engineers utilize advanced tools to design precision and quality into each product. We are dedicated to providing high quality services that meet or exceed customer requirements.
-
product
Stand-Alone Test Fixture
MA 2012/D/H
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 15,50 kg
-
product
Customized Services
We work in close collaboration with our customers to develop tailor-made test methods to meet their specific application requirements. Our 140 years of combined varied experience has allowed us to design solutions suited to address the needs of our customers in the most complex environments from space to deep sea.
-
product
Standard And Custom Targets
Santa Barbara Infrared manufactures a wide range of targets for visible, and infrared/FLIR electro-optical testing. These targets complement our complete line of Visible and IR test products. Our targets are designed to function with one of SBIR’s target wheels. Utilizing a variety of manufacturing techniques, including conventional machining, photochemical etching, electro-deposition, electrical discharge machining (EDM) and laser cutting. SBIR targets are manufactured to exacting mechanical tolerances. SBIR manufactures all of the targets specified by MIL-STD-1859 and the Tri-Service Guide for thermal imager testing.
-
product
Standard RF Fixture
The standard RF fixture supports both pulsed and non-pulsed operation. It employs SMA input/output connections. For RF output powers over 10W, an N-type connector may be used to replaces the SMA connector because of its power-handling capability.
-
-
product
Custom Ultrasonic Transducers
Blatek ultrasonic transducers are designed to meet custom apecifications using our proprietary piezocomposite. We take pride in our ability to design and manufacture ultrasonic probes to the exact design our customers provide. Our staff is experienced in working with customers through the transition from prototype to product. We have produced phased array, linear array, and curved linear array transducers, all with broad bandwidth, high sensitivity, and excellent element to element uniformity.
-
product
ADI Test Fixture
TA-6500
The TA-6500 test fixture combines the features of the OEM's Instrument Servo Tester(T307962), the Pointer/Flag Test Fixture(T307951) and the AD-650/600 Test Panel(T334043) all into one panel to facilitate testing of these Attitude Director Indicator's. The panel switches and adjustment pots are labeled to match the test procedure numbers and the duplicity in marking makes it easier for the technician to understand each function. The UUT interface is through a 96 pin zero insertion force(ZIF) type connector to minimize contact wear. The expanded localizer and nav input pins J2-34/35 are exposed on the panel to facilitate the insertion of a 200 ohm shunt when required. The fixtures rear panel has connectors for the required dual API/Synchro transmitter interface while the panel switches provide the correct routing of each.
-
product
Vacuum Fixture Kits
*Perfect Sealing *Precise Operation *Stable Construction *Self Closing - Opening Covers
-
product
Bottom Electrode SMD Test Fixture
16197A
The 16197A is designed for impedance evaluations of bottom electrode SMDs. It achieves stable frequency characteristics up to 3 GHz and provides highly repeatable measurements. The Keysight 16197A supports various SMD sizes, as small as 1005 (mm)/0402 (inch) and as large as 3225 (mm)/1210 (inch). Accommodation of the 0603 (mm)/0201 (inch) size is available with option 001.
