Memory Test Systems
-
Product
Sensing System
DTS
-
Our Distributed Temperature Sensor(DTS)with operating system is designed for easy installation and management in the field.Several DTS units can be controlled remotely by Ethernet configuration.
-
Product
Bypass Diode Thermal Test System
-
King Design Industrial Co., Ltd.
* Power: the heating board control panel uses 220V single-phase power.* Power consumption: 1.0KVA, 1000W(Max)* Volt: 220VAC* Current: 4.5A* Heating board: one controller per board* Power rate: room temperature raise to 75°C± 5°C within one minute.* Heating board dimension: 500mm x 1,000mm* 6-sheet electrical heating boards test: used to test the 2,200mm x 2,600mm module. It can be customer-designed.* The length of board power cable and thermal sensor cable shall exceed 3,000mm.* To get uniform heating effect, the electrical board is sandwiched by 2mm aluminum sheets at both sides of board.
-
Product
OPTICAL PHASE NOISE TEST AND MEASUREMENT SYSTEM
-
OEwaves’ HI-Q® Optical Test Measurement System utilizes a homodyne methodology for automated measurement capable of testing ultra-low phase noise laser sources. The user friendly test system is capable of rapidly measuring laser phase noise and estimating its FWHM linewidth down to < 3 Hz without complex setup or reference lasers normally required to make such a narrow linewidth measurement.
-
-
Product
Multi-Sensor Systems
-
Multi- sensor surveillance systems represent a fast growing group of electro-optical systems of critical importance in both defense and civilian applications. At the same time they are the most expensive groups of electro-optical systems. Most advanced but rarely met multi-sensor surveillance systems are built from a long series of sensors like thermal imager (or two thermal imagers, color VIS camera, low light VIS-NIR camera, SWIR camera, laser range finder, laser designator, laser pointer, illuminator located on a stabilized platform and such systems. Simpler systems built from two-three sensors located on smaller stabilized or non-stabilized platforms are more common.
-
Product
Inertial Systems
-
ACEINNA’s inertial systems provide end-users and systems integrators with fully-qualified MEMS-based solutions for measurement of static and dynamic motion in a wide variety of challenging environments, including; avionics, remotely operated vehicles, agricultural and construction vehicles, and automotive test.
-
-
Product
Automation Systems
-
Omron's extensive portfolio of PLC and MAC controllers, networking solutions, remote IO, IPC and HMI technology support a fully integrated application
-
Product
(2500kN+) Fatigue Testing Systems
8806
-
The precision mechanical systems, combined with the advanced features of the 8800 digital controller and Dynacell™ load cells, enable Instron to supply fully-integrated turnkey solutions to meet the most demanding applications. The system can be used to cover a broad range of static and dynamic test applications, covering metals, rebar, high-force fracture mechanics, aerospace panels, civil engineering components, wire ropes, or concrete.
-
Product
Supported Test Systems
-
TTCI is a leading solutions provider of application development for test systems from Seica, Keysight, Teradyne, Digitaltest, and XJTAG. We offer a wide variety of testers and test solutions to meet your needs. Our Seica Pilot and Digitaltest Condor flying probe systems can handle all of your low- to mid-volume production, prototypes, and PC boards with accessibility issues. The Keysight 3070 and Teradyne TestStation can address your larger production runs and fixture requirements. In addition, we can also address your functional and boundary scan needs.
-
-
Product
Software-based Electroacoustic Test System
SoundCheck
-
The SoundCheck®system from Listen includes everything you need to perform audio measurements on a wide range of devices – the software, the audio interface, other test interfaces and accessories, and test sequences.The system is centered around the SoundCheck software. This powerful package controls and communicates with the measurement hardware, and includes all the stimuli, algorithms and analysis functionality needed to develop and run virtually any electroacoustic or audio electronic test. It is paired with hardware ranging from a simple, all-in one audio test box to sophisticated discrete components for a complete test system. In addition to Listen hardware, a range of 3rd party products and test accessories are fully supported within SoundCheck.
-
Product
Ethernet and Fibre Channel Test Platform
SierraNet M1288
-
The SierraNet M1288 Ethernet and Fibre Channel test platform provides best in class analysis, jamming and generation for traffic capture and manipulation for testing application and link characteristics. SierraNet M1288 is the latest in the line of industry leading test and measurement tools from Teledyne LeCroy, designed for today’s high-speed storage and communications fabrics. SierraNet M1288 supports examination and modification of Ethernet and Fibre Channel links utilizing both Pulse Amplitude Modulation 4 (PAM4) and legacy Non-Return to Zero (NRZ) technologies.
-
Product
System
SYS-28
-
This 28" box coater has a separately ventable top chamber, to allow for faster parts changes and increased productivity. It also is equipped with our FTC-620 flip controller. The flip and rotation motors can be seen on the top. This system uses a Varian tri-scroll pump and a bottom mounted 16" APD cryopump.
-
Product
In-System Test Programming System
WriteNow
-
Based on proprietary WriteNow! Technology, the WriteNow! Series of In-System Programmers is a breakthrough in the programming industry. The programmers support a large number of devices from various manufacturers and have a compact size for easy ATE/fixture integration. They work standalone or connected to a host PC, and are provided with easy-to-use software utilities.
-
Product
Transformer Test System
-
Transformer testing instrument, can be used as a stand-alone device and has the highest efficiency. Can be used in power transformers, network communication transformers, etc.
-
Product
Switchgear Test Systems / Circuit Breaker Testing
-
ACTAS test systems provide precise information as to the condition of the chamber and drive unit without requiring them to be opened. The sheer number of parameters to be determined, the wide variety of different types of switchgear equipment in use and the harsh environmental conditions encountered during on-site tests place extreme demands on test equipment.
-
Product
Modular Battery Test System
-
This modular battery test system provides for manufacturers versatile testing possibilities. Due to modularity it allows easy configuration of battery testers for a wide range of different power levels.
-
Product
Laser Distance Meter for 60m With 10 Memories and Min. Measurement
MS-LDM360
-
*Measuring distance: 0.05 to 60m*Accuracy: ±1.5mm (±0.06in)*Unit conversion: mm/in/ft*Laser classification: Class 2*Laser type: 635nm <1mW*Dynamic measurement*Area, volume measurement*Pythagorean proposition measurement*Indirect measurement*Add - subtract calculation*Minimum measurement
-
Product
Motor Drive Test Systems
-
Drive and motor systems present unique challenges for test systems and Intepro combines regenerative active electronic loads to reduce the energy needed to do the tests as well as sophisticate instruments and supply voltages to test these demanding applications and provide meaningful results for the electrical and mechanical power parameters.
-
Product
Cleanliness Test Systems
CM Series
-
The Contaminometer (CM Series) test systems were originally developed by Protonique, the business of industry guru Brian Ellis. They also featured in the early development programmes of "cleanliness measurement" carried out by the US Department of Defense at China Lake in the 1970s.
-
Product
Lithography System
JetStep X500
-
The JetStep X500 panel lithography system is optimized for volume manufacturing of high-end AICS and advanced packaging panels. The system incorporates a large field exposure system with advanced features to meet the challenging requirements encountered in production of AICS or panel level packaging, such as; fine resolution to 3µm with large depth of focus (DOF), high overlay accuracy of ±1µm, automatic magnification compensation with independent x and y magnification adjustment of ±100 ppm, and automatic handling of panel substrates of various dimensions, thicknesses, and levels of warp.
-
Product
Multiple-Bus Architecture Cable/Harness Test System
CKT1175-MBA
-
The CKT1175-MBA (for multiple-bus architecture) will provide seamless testing of electronic racks, panels and chassis containing passive and active components such as relays, solenoids, switches, circuit breakers, lamps and LED's, diodes, resistors, capacitors, etc. This functionality is made possible by a switching matrix that is up to 10 levels deep, plus a multiplexer that controls the various stimuli sources, instrumentation connections, and external energization outputs.
-
Product
Monitoring System
Sensaphone WSG30
-
The Sensaphone WSG30 Monitoring System offers a flexible monitoring solution when hard-wiring sensors is not a cost-effective or viable option. It also functions as a data logger to demonstrate compliance. The WSG30 is encased in a stylish, wall-mountable enclosure with an easy-to-read, 80-character LCD display.
-
Product
6TL24 Combinational Base Test Platform
H71002400
-
The 6TL24 is the Base platform ideal for Combinational test (ICT+FCT) in low to mid volume, high-mix electronics productions. A dual-stage pushing mechanism will allow performing both, the FCT and the ICT test, without the need of changing the test platform and with a low cost fixturing technology. To do so, the exchangeable cassette fixture must be designed with two-level probes. IN the 6TL24, the second level is reached thanks to a pneumatic actuator.
-
Product
Exposure Systems
Model 2000AF & 2000SM
-
The OAI Model 2000 Exposure Systems may be configured as either an edge-bead exposure system (2000SM) or a flood exposure system (2000AF); both configurations are based on OAI’s proven, time-tested platform.
-
Product
DTP Systems
-
A versatile range of products designed to support long distance signal transmission over shielded twisted pair cable in AV switching environments.
-
Product
QE System
PVE300
-
The PVE300 system is a monolithic,turnkey solution for photovoltaic material and device characterization;a key component in research, or as part of a production-line quality process.
-
Product
HardFiber System
IEC 61850
-
The HardFiber System is a KEMA tested IEC 61850 Process Bus Solution that allows the mapping of measurements made in the switchyard to protection relays located in the control house using secure communications. The HardFiber System addresses the key technical and logistic challenges affecting the labor required for substation design, construction and maintenance.
-
Product
Embedded Systems
-
Embedded systems consist of computer hardware, input and output (I/O), and software typically used for system control or monitoring applications. Our engineers are experts at integrating control system electronics with components and sensors, including motors, pumps, valves, signal transducers, and much more. We have developed and deployed thousands of systems that include industrial assembly lines, scientific instruments, medical devices, large installations like factories, manufacturing equipment, and electrical grids that rely on multiple embedded systems networked together.
