Counting
-
product
Quadrature Position & Rate Meter
Accepts low-level differential or single-ended 5 V logic level quadrature signals from shaft encoders to display scaled position or scaled rate. One, two or four transitions may be counted at a maximum combined rate of 250 kHz and be mathematically scaled to display in engineering units from -999,999 to +999,999. An analog output scaled to the display and relay outputs are optional.
-
product
USB-6361, 16 AI (16-Bit, 2 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device
782254-01
16 AI (16-Bit, 2 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device - The USB-6361 offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6361 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
product
PXI BRIC8 FIBO Matrix Dual 80x4 3pin brkout
40-592A-104
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
product
Particle Counter Emissions Tester
PARTICLE COUNTER | VP 135046
Maschinenbau Haldenwang GmbH & Co. KG.
With the PARTICLE COUNTER emission tester, you can really count every particle. Compact, rugged design, clearly readable display, rapid readiness for measurement and precise measurement results are the distinguishing features of the MAHA particle counter.
-
product
PXI/PXIe Very High Density Multiplexer, 5-Channel, 32-Pole
40-675B-002-5/32
The 40-675B-002-5/32 (PXI) and the 42-675B-002-5/32 (PXIe) are 5-channel, 32-pole multiplexers and are part of our range of very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems. They use high quality electromechanical signal relays allowing each channel to switch current up to 1 A at 150 VDC/100 VAC. Connections are made via a front panel 200-pin connector.
-
product
PoE Ethernet I/O Module w/ 3-axis Encoder/Counter Inputs
PET-7083
A great device, that works well for building automation, factory, and machine automation, remote maintenance, testing, and diagnosis, the PET-7083 is a 3-axis high speed encoder/counter module. Its each axis can be individually configured for Quadrant, Pulse/Direction or CW/CCW counting modes. The maximum input rate for Quadrant counting mode is 1 MHz, and for Pulse/Direction, CW/CCW counting modes is 4 MHz. The encoder/counter module is equipped a FRAM to retain the counter value after it is powered off. FRAM is a nonvolatile memory that can hold written data even after it is powered off. The data retention can be 10 years. And the feature can be configured as enabled or disabled.
-
product
DIGITAL MULTIMETER, MEAN VALUE, 20A, 1KV
72-13500
*Digital multimeter with 2000 counts display*CAT II 1000V, CAT III 600V safety rating*Manual function select and manual ranging*Data hold*Full icon display*Powered by 9V battery (6F22)*12-month limited warranty *view Terms & Conditions for details
-
product
Wireless Digital Multimeter 4000 count / NCV / SPT / Anti Burn Protection and with Max./Min./Max.-Min. display
MS-W2044P2
This is a external wireless connectivity Digital Multimeter integrated with 4000 Count, True RMS auto and manual measurement.
-
product
PXIe-2575, 196‐Channel, 1-Wire PXI Multiplexer Switch Module
780587-75
196‐Channel, 1-Wire PXI Multiplexer Switch Module —The PXIe‑2575 is a high‐density PXI multiplexer switch module that is ideal for high‑channel‑count automated test applications. It uses electromechanical relays and can route hundreds of signals to measurement devices or from source units. The PXIe‑2575 also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
product
Multi-Channel, 10-Bit Digitizer
ADQ8-4X
ADQ8-4X offers software-configurable sampling on two or four channels. The sampling rate is 4 GSPS in two-channel mode or 2 GSPS in four-channel mode. This feature enables flexible operation during development since the channel count and sampling rate can be varied.The signal inputs are DC-coupled and offer programmable DC-offset as well as configurable input voltage range. It also supports high analog input bandwidth and therefore supports a wide range of sensors.
-
product
Data Acquisition Software
Data System - DS
APEX Turbine Testing Technologies
From 4 to 400+ channels to support testing requirements. Networked architecture for flexibility and large channel counts. All channels can be synchronized. Multiple pages; multiple windows with no loss of plot data when changing pages.
-
product
PXI High Density MUX BRIC, 4-Chan, 160-Pole
40-570-014
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
product
Universal Test Fixture
Series 48
The Series 48 Universal Test Fixture Systems are an effective way to test high mix, low to medium volume products. The Universal Base is designed around the CAMGATE Z axis Test Fixture. The base interfaces with removable, quick change Series 49 Universal Test Insert Kits. Three versions are offered, a blank base whereas the end user can configure the Base and insert kit to their own connector configuration, The 160 point model which uses four (40) pin IDC ribbon cable connectors to interface between the base and the insert kit, and the -I model that incorporates the same 4 block GR2270 style block interface as used on our Series 34 test fixtures. This allows for increased test point count and the use of Industry Standard 2270 style signal, power, and coax blocks. Rear panels can be custom configured to customer specifications, Virginia Panel ITA frames, or GR2270 Interfaces used on Semco’s Standard Product line
-
product
PXI Programmable Resistor Module 10x8 Bit, 0 Ohm to 255 Ohm
40-295-021-10/8
The 40-295 is a Programmable Resistor module with up to 18 channels of 8-bit resolution resistor chains in a single 3U PXI module. The flexible architecture allows these modules to also be supplied as 12, 16 or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count.
-
product
Quadrature Input PCI Cards
PCI-QUAD-8
The PCI-QUAD-8 provides quadrature counting on a convenient half-length PCI card. Up to eight differential encoders (each with A, B, and Index) can be monitored simultaneously.
-
product
Compact Digital Multimeter
MT-1705
1/2 digits 1999 counts.0.5% best accuracy.CAT III 600V safety rated.Auto polarity indication.AC True-RMS for accurate measurements.Large backlight LCD display for easy reading.Extra Functions: Continuity with beeper, Diode test, Data hold, Auto power off, Low battery indication, Overload indication, LCD backlight,Frequency and Capacitance are auto rangeIdeal for wide variety of electrical and electronic testing applications.
-
product
High Density
Smaller diameter cables with higher fiber counts for scalable, flexible networks.
-
product
ASCOR Switching
Count on ASCOR by Astronics switching products for proven performance in your most demanding high reliability applications. Compatible with VXI and PXI platforms, these switching products provide complete switching solutions for the systems of yesterday, today, and tomorrow.
-
product
PXIe-4143, 4-Channel, ±24 V, 150 mA Precision PXI Source Measure Unit
782431-01
PXIe, 4-Channel, ±24 V, 150 mA Precision PXI Source Measure Unit - The PXIe-4143 is a 4-channel source measure unit (SMU) ideal for high-pin-count applications. It features 4-quadrant operation and each channel has integrated remote (4-wire) sensing for accurate measurements. The fast sample rate of the PXIe-4143 can reduce measurement times, capture transient device characteristics, and allow quick I V characterization of devices under test (DUTs). With a high-speed sequencing engine, you can synchronize all these SMUs with each other or with other instruments such as switches or high-speed digital test modules. Additionally, you can tune the PXIe-4143 response to any load to achieve optimum responses with maximum stability and minimum transients using SourceAdapt technology.
-
product
Mechanical Counter
SP101/102 Series
The SP-101/102 Series is a heavy duty totalizer. It has a double sided shaft for stability. Available in Revolution or Rotary type movements. Input shaft direction is choice between top going or top coming. Count speed range from 300 ~ 3000 rpm. It is a available in 4 or 5 digits with a large digit size of 6.0 x 4.0mm. Resetting of count value is done easily with the front push button reset.
-
product
3 Wire (Digital) Earth Resistance Tester
ST-1520
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● Auto power off function.● The timer operates automatically for about three to five minutes when the "PUSH BUTTON SWITCH" and "TIMER ON BUTTON" are pressed together. This will keep test "ON" for the duration of the timer.● Timer for test function (count 3-5 minutes).● Battery operated.● Data hold function.● Small and light weight.● Calibration performed with supplied test leads.
-
product
Wrap Reel
TESTEX Testing Equipment Systems Ltd.
Wrap Reel, to produce skeins of yarn of a pre-determined length and number of turns for count and strength testing. Yarn Length Measuring Device complies with ISO 2060, ASTM D1907/2260, BS 2010, etc. Wrap reel yarn testing will be more accurate if you use our Wrap Reel.
-
product
Wide-Field FLIM System
LINCam FLIM
*Easy to Use Like an Ordinal Megapixel CCD Camera*Spatial Resolution ~ 1024 x 1024 Pixels*Temporal Resolution (IRF Width) 50 ps FWHM*Single-Photon Sensitivity*Saturated Count Rate Up to 5 MHz*Excitation by bh BDS-SM Family ps Diode Laser*Works with All Commonly Used MicroscopesI*llumination via Single-Mode Fiber*Lens System for Image Transfer Into Camera
-
product
Backplane Test System
402HV
Our model 402HV is the result of 25 years of high voltage / high pin count test systems experience. We produced our first high voltage system back in 1985. It was programmable up to 600 volts / 600 Mohms and had over 49,000 test points. It could test a 5k point board in less that 15 seconds. Since then we have built hundreds of high voltage test systems, with our highest voltage system capable of testing up to 2000 Volts DC / 1500 Volts AC. (One of our 600 volt systems, built in 1986 is still in operation testing boards for a defense contractor.)
-
product
PXIe-2526 , 158‐Channel, 2 A PXI Multiplexer Switch Module
780587-26
158‐Channel, 2 A PXI Multiplexer Switch Module—The PXIe‑2526 is a high‐density PXI multiplexer switch module that is ideal for routing signals within automated test systems. It uses electromechanical relays to perform immediate switch operations in either a 158x1 1‑wire or 79x1 2‑wire multiplexer topology. The PXIe‑2526 also features onboard relay counting for relay monitoring.
-
product
USB-6366, 8 AI (16-Bit, 2 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device
782264-01
8 AI (16-Bit, 2 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device - The USB-6366 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6366 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
product
Compton Suppression Counting Systems
Compton-Suppression Systems are used to reduce the background continuum for low-background counting, thus improving the Minimum Detectable Activity and overall spectrum quality – particularly for small volume samples such as air filters and petri dishes.
-
product
6000 count Wireless Connectivity Digital Multimeter with replaceable fuse and data connect to Smart phone
MS-WM86
This is a compact, mini size, external wireless connectivity Digital Multimeter integrated with 6000 Count, True RMS auto and manual measurement.
-
product
DIGITAL TURNS TESTER AND DIGITAL LCRTZ METER
TURNS-LCRTZ
Digital TURNS TESTER with LCR for Counting / Measuring Number of Turns for Toroidal Coils , Current Sensor , Current Transformer , Round Core Coils. Can measure, Turns along with Winding Polarity , DC Resistance , Inductance (L), Capacitance (C), DC Resistance, Rac, Q, D, ESR and Tan.Toroidal Turns Platforms :TTPT100 : 5 T - 1000 T , TTPT1000 : 500T-10000 T The Platform has 2 connections for the coil and 2 for the probe wire. Measurement principle is based on dynamic comparison of the voltage across one turn and the coil. You will be able to get the polarity or winding indication with respect to the one turn reference.Accuracy : + 0.2% + 0.5T for high and medium permeability cores at suitable test frequency. Internal Diameter must be able to pass a wire as thin as 0.2 mm. External Diameter as high as 200 mm.Test Frequency Selectable in Step : 50 Hz, 100 Hz , 500 Hz, 1 KHz, 5 KHz, 10 KHz. Test Voltage adjustable : 100mV to 1V in steps of 50mV.
-
product
Digital Multimeter
PT-30
Standard Electric Works Co., Ltd
● Lightweight, compact, and easy to use.● 4000 counts.● Full automatic measurement, voltage measurement, resistor measurement.● Data hold function.● Auto off function.● Continuity check.● Diode measurement.● Low battery indication.● Pen light provided.● Backlight LCD.● 3V DC power supply.
