Burst
-
Product
Mini Burst Field Generators
-
Mini burst field generators are small and handy burst generators used to detect weak spots in the device under test.
-
Product
H-Field Burst Detector
BD 11
-
The BD 11 is used to detect a burst or ESD current pulse on a cable, for example in a complex system. This makes it easier to investigate the causes of sporadic faults in the system. It is small and handy, its sensitivity is very high and continuously adjustable.
-
Product
Accessory EFT/Burst generators IEC 61000-4-4
-
The field sources and the burst transformer are used to harden the device under test. They are powered by an EFT/burst generator.
-
Product
Burst Detectors
-
The Burst detector monitors interference threshold exceedances at cable-and line bundles. It selectively detects conducted disturbances, which would influence the monitored device.
-
Product
Burst-Generator
SFT 1420
-
The test generator SFT 1420 simulates quick transient noise interference as they are defined in the standard IEC / EN 61000-4-4. The single pulses show a very short rise-time (5 ns) and due to this a wide RF-spectrum up to 300 MHz. RF interferences are the result.
-
Product
EFT/Burst Simulators
-
Suzhou 3ctest Electronic Co.,Ltd.
High-end test instrument of EFT/Burst for new energy, which fully comply with CE and CCC certification. With a built-in three-phase five-wire automatic coupling /decoupling network EFTN 69100T, it can meet the requirements of new energy test system and high power load test. It is featured with good reliability, stable performance and easy use.
-
Product
64-Channel 500kSa/s USB Modular Multifunction Data Acquisition
U2356A
-
The U2356A offers multifunction capabilities in a module. It can be used like a digital multimeter in polling mode. It can be transformed to be a simple scope using the continuous mode with simple triggering capabilities. No matter if it is used as a standalone module or when plugged into a U2781A USB modular instrument chassis, the synchronization and triggering capabilities allow great flexibility in making the desired measurements. With the analog output being able to send out predefined or arbitrary waveforms make this a good tool when closed loop feedback or stimulus is required. The digital IO channels allows for closed loop control through connections to switches, relays and solenoids. The burst mode enables the U2356A to simulate simultaneous analog input acquisition.
-
Product
16G DDR5-4800 288Pin 2GX8 1.1V Registered Samsung Chip
AQD-D5V16GR48-SB
-
Samsung Original Chip, Dual 32-bit Subchannels. Increased Banks and Burst Length, DDR5 4.8GT/s. Same-Bank Refresh, On-die ECC for Enhanced RAS.
-
Product
8GB SO-DIMM DDR5-5600 262Pin 1GX16 1.1V Unbuffered Hynix Chip
AQD-SD5V8GN56-HC
-
Hynix Original Chip, Increased Banks and Burst Length, DDR5 5.6GT/s. Same-Bank Refresh, On-die ECC for Enhanced RAS.
-
Product
13.56MHz RF Power
-
100 W to 2400 W. 13.56 MHz. Analog/Digital, RS-232, USB interfaces. Low Harmonic Distortion. Automatic and Manual Gain Control. High Speed Pulsing (Bursting) controls. Compatible with T&C's Matching Networks. GUI Software (complete PC control). Includes all essential RF power/communication cables and mounting brackets. Air cooled (Air & Water 1200 W +). Half rack mount or stand alone versions. Ideal for: Industrial, Scientific, and Medical Applications.
-
Product
Touch-Screen Paper Bursting Strength
DRK109B
-
Shandong Drick Instruments Co., Ltd.
DRK109 touch-screen paper bursting strength tester, an international general Mullen instrument , is basic instrument for measuring the strength of paper and board. This instrument being simple to operate, with reliable quality and advanced technology is the ideal instrument of scientific research units, paper manufacturers, packaging industry, quality inspection departments.
-
Product
16-Channel 500kSa/s USB Modular Multifunction Data Acquisition
U2354A
-
The U2354A offers multifunction capabilities in a module. It can be used like a digital multimeter in polling mode. It can be transformed to be a simple scope using the continuous mode with simple triggering capabilities. No matter if it is used as a standalone module or when plugged into a U2781A USB modular instrument chassis, the synchronization and triggering capabilities allow great flexibility in making the desired measurements. The digital IO channels allows for closed loop control through connections to switches, relays and solenoids. The burst mode enables the U2354A to simulate simultaneous analog input acquisition.
-
Product
32G DDR5-4800 288Pin 2GX8 1.1V Unbuffered Samsung Chip
AQD-D5V32GN48-SB
-
Samsung Original Chip, Increased Banks and Burst Length. DDR5 4.8GT/s, Same-Bank Refresh, On-die ECC for Enhanced RAS.
-
Product
Vector Finders with InternalAttenuators
VF-145 LA AND VF-145 LMA
-
The VF-145 LA and LMA models are functionally the same as the VF-145 L and LM on both electrical performance and mechanical specifications. However, the LA and LMA models include an internal PIN diode attenuator that provides up to 12 dB of attenuation (measured at 150 MHz, attenuation decrease slightly as operating frequency increases) to the incoming radio signal. This attenuation occurs after the signal is received by the unit and phase shifted for processing, but before it is placed on the coax feedline to the receiver. In addition, the PIN diode utilized will absorb short burst of RF should transceivers be keyed accidentally by the user. This feature aids in very strong signal DF operations but will not totally guarantee against system overload under very strong RF emissions.
-
Product
Arbitrary Waveform Generators
AWG-8200
-
The AWG-8200 is an agile waveform generator designed for linear frequency chirp, CW burst , and arbitrary waveform applications. It is based upon a modular programmable digital signal processing baseboard engine with an integrated 32-bit processor, high-performance FPGA, and two versatile daughtercard ports that can be clocked up to 1 GHz. Communication to the baseboard is provided by Ethernet and RS-232 ports for programming waveform and control parameters.
-
Product
Vector Signal Analyzers
-
Vector signal analyzers combine superheterodyne technology with high speed ADCs and other DSP technologies to provide fast FFT-based, high-resolution in-channel spectrum measurements, demodulation, and advanced time-domain analysis. A vector signal analyzer is especially useful for characterizing complex burst, transient, or modulated signals in aerospace & defense, radar, wireless communications, and avionics.
-
Product
Timing Board #1
TIO-10 #1
-
Interface board for converting signals on a National Instruments PC-TIO-10 timing board to and from fiber optic signals. Bursts, delayed pulses, and frequencies can be generated on outputs. The input channel can be used to measure frequency or period.
-
Product
4-CH 16-Bit 80 MS/s PCI Express Digitizer
PCIe-9834
-
ADLINK's new PCIe-9834 high-speed PCI Express digitizer, featuring four simultaneously sampled 80 MS/s input channels with 16-bit resolution, 40 MHz bandwidth, and up to 1 GB DDR3 onboard memory. Each of the four input channels supports up to 80MS/s sampling, with 16-bit resolution A/D converter. This allows simultaneous recording of signals on all channels with no interchannel phase delay. The extremely large onboard memory enables long recording times even at the highest sampling rates. Each connection pair (lane) can achieve burst connection speeds of 250MB/s. The PCIe-9834, based on x4 lane slot PCI Express technology, provides a clear advantage in that direct connection of each slot allows full transfer bandwidth for each individual card.
-
Product
Burst Mode Bi-Directional Optical Receiver
RFoG1000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
RFoG1000 series RFoG ONU, adopts Passive Optical distribution Network (PON) to realize bi-directional, interactive RF business. In FTTH network, it serves to transmission layer of RF video, DAVIC, DOCSIS, extending the optical network to home or building without the need of adjacent HFC optical node. Saving lots of RF amplifier, thus, it can improve the quality and stability of network operation.
-
Product
16G DDR5-4800 288Pin 2GX8 1.1V Unbuffered Samsung Chip
AQD-D5V16GN48-SB
-
Samsung Original Chip, Increased Banks and Burst Length. DDR5 4.8GT/s, Same-Bank Refresh, On-die ECC for Enhanced RAS.
-
Product
350 MHz Universal Frequency Counter/Timer, 12 digits/s, 20 ps
53230A
-
The Keysight 53230A universal frequency counter/timer serves all your frequency and time interval measurement needs. In addition to the typical frequency and time interval measurements, continuous/gap-free measurements are available for basic modulation domain analysis. Optional burst measurement software is available. An optional microwave channel can be added to measure 6 or 15 GHz.
-
Product
Network Emulation System
Mini Maxwell
-
Mini Maxwell -- Easy to use, portable, network emulator. Mini Maxwell''''s low cost of $1995 can fit into any testing budget. The Mini Maxwell is great if you have low power requirements, or need ultra quiet operation. Mini Maxwell supports packet drop/loss, duplication, delay (latency)/jitter, reorder, and burst. Includes: processor, memory, and three Ethernet interfaces in one enclosure with separate power supply, Linux OS, Mini Maxwell network emulator engine, graphical user interface, and 90 Day Warranty.
-
Product
Ultra-Low Distortion Function Generator
DS360
-
Stanford Research Systems, Inc.
The performance of a low distortion analog source and the precision of direct digital synthesis (DDS) is combined in the DS360. With less than 0.001 % total harmonic distortion (THD), 25 ppm frequency accuracy, and a broad range of features including sweeps and bursts, the DS360 is the ideal source for audio frequency applications.
-
Product
PCI Bus Analog Output Board, 4 Isolated Outputs, 14 Bit
APCI-3501-4
-
4 analog output channels Optical isolation 500 V Settling time 30 µs typ. 14-bit resolution (13 bit for 0-10 V) Output voltage: ±10 V, 0-10 V (switchable through software) Output voltage after reset: 0 V Each output channel has its own ground line (without optical isolation from the others) Driver capacity: 5 mA/500 pF Short-circuit protection, EMI filters Noise neutralization of the PC supply Creeping distance: 3.2 mm acc. to DIN VDE 0411-100 Watchdog for resetting the analog output channels (4 different time units: µs, ms, s, min) or as 12-bit timer (with interrupt possibility), when the watchdog function is not necessary2 digital input channels, 24 V, isolated 2 digital output channels, 24 V, isolated Noise immunity Test level: ESD: 4 kV Fields: 10 V/m Burst: 4 kV Cond. radio interferences: 10 V
-
Product
EVISION Obstacle Detector
MS 1528
-
Obstacle Detector is a distance-measuring system based on ultrasonic sound utilizing the LPC2364FBD100. The system transmits a burst of ultrasonic sound waves towards the subject and then receives the corresponding echo. The LPC2364FBD100 integrated analog comparator is used to detect the arrival of the echo to the system. The time taken for the ultrasonic burst to travel the distance from the system to the subject and back to the system is accurately measured by the LPC2364FBD100. Assuming the speed of sound in air at room temperature to be 1100 ft/s, the LPC2364FBD100 computes the distance between the system and the subject and gives the information to buzzer. The minimum distance that this system can measure is eight inches and is limited by the transmitter’s transducer settling-time. The maximum distance that can be measured is 2 meter. The amplitude of the echo depends on the reflecting material, shape, and size. Sound-absorbing targets such as carpets and reflecting surfaces less than two square feet in area reflect poorly. The maximum measurable range is lower for such subjects. If the amplitude of the echo received by the system is so low that it is not detectable by the Comparator. This system is mainly used to replace normal sticks for the visually impaired (blind) peoples. This unit has standard USB 2.0 for mobile interface and has android application for user interface
-
Product
Edge AI Inference System
AIR-101
-
Edge AI Inference System powered by Intel Atom® E3940 QC SoC and two Intel MA2485 VPUs. Intel Atom E3940 Quad Core SoC turbo burst up to 1.8 GHz. Intel® Movidius™ Myriad™ X VPU MA2485 x 2 Built-in.
-
Product
Immunity Development System
-
Used for EMI suppression in printed circuit boards during the development phase. The developer can use the E1 set to quickly identify the causes of burst and ESD interference. This allows the developer to design suitable measures to solve the causes of the interference. It can also be used to test the effectiveness of the measures taken.
-
Product
Leak and Seal Strength Tester
LSSD-01
-
LSSD-01 Leak and Seal Strength Tester is suitable for the quantitative measurement of sealing strength, heat sealing strength, binding strength, overall sealing performance, pressure resistance strength, cap body connection strength, bursting pressure and shedding strength. It is widely used in the soft package, plastic pilfer-proof caps, flexible pipes, etc.
-
Product
Cloud-Based One System Platform
VeSion
-
VeEX''s VeSion is a Cloud-Based, One System Platform, representing the next step in innovation for Network Monitoring. VeSion integrates RFmonitoring systems (Return and Forward), advanced DOCSIS Monitoring, DOCSIS Burst Demodulation, Sweep, Ethernet, MPEG, and Workflow and Asset management system, all under one umbrella. VeSion''s one system concept reduces network troubleshooting and problem resolution time significantly.
-
Product
Femtosecond Laser
DIADEM
-
DIADEM is a high-energy, versatile femtosecond fiber laser operating at either 1030 or 1064 nm in the most compact and robust air-cooled configuration on the market. DIADEM produces pulses of < 400 fs up to 40 µJ with many pulse control features such as adjustable pulse duration, selectable repetition rate from 40 MHz down to single pulse, or fine pulse energy tuning so that pulses can be emitted in various modes (on demand via external signal, burst of pulses with configurable pulse separation).
