Calibration
maintains accuracy of test asset by correcting out of specification conditions.
See Also: Calibrators, Power Calibration, Display Calibration, Calibration Standards, Calibration Software, Calibration Services, Calibration References
-
Product
Relative Humidity Calibration Services
-
PST have calibration laboratories offering Relative Humidity calibrations in six locations across the globe.
-
Product
Balanced and UFL Calibration Kit
CAL-UFL-BAL
-
The Balanced Calibration Kit is an interface kit for UFL and balanced VNA measurements. It contains SMA-UFL adapters and several adapters from SMA and UFL to balanced pinheaders. The UFL connector was introduced by Hirose as the U.FL connector and became very popular for connecting RF signals in consumer electronics. There are several varieties from other manufacturors and are also known as UMC or UMCC connectors.
-
Product
Electronic Calibration Module (ECal), 40 GHz, 2.92 Mm, 2-port
N4692D
Electronic Calibration Module
The Keysight N4692D microwave electronic calibration (ECal) module makes calibration of Keysight vector network analyzers fast, easy and accurate. The N4692D is a precision 2-port ECal module that supports 2.92 mm connectors up to 40 GHz. Select either female-female, male-male, or female-male connectors. The plastic storage case for the N4692D is included for securing your ECal module and accessories.
-
Product
4-in-1 OSLT Calibration Kit, DC to 50 GHz, 2.4 mm (m)
CK564A
-
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
Product
NIST Calibration for D400A-AT
D400A-AT-CCNIST
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
Seismic Transducers Calibration System
-
Calibration of the seismic sensors should be conducted in the low-frequency domain, which means, that the relative method used for calibration of the vibration transducers is not applicable since it does not guarantee the required accuracy level. The problem is that the reference accelerometers have uneven AFR characteristic in the low-frequency domain. Thus, calibration of seismic transducers requires implementation of a different approach.
-
Product
Three Phase Portable Energy Meter Calibration Equipment
GF302D1
-
Beijing GFUVE Electronics Co.,Ltd.
The GF302D1 three phase portable energy meter test system consists of an integrated three phase current and voltage source(up to 500V/120A or 500V/20A) and built-in three-phase electronic reference standard of accuracy class 0.05%. Characteristic features of the GF302D1 are its wide measuring range, high accuracy and high tolerance to unwanted external influences. The equipment offers high functionality combined with an excellent menu guided operation via built-in keyboards and colored 7" touch LCD-display.
-
Product
IndySoft for Calibration Management
-
The IndySoft Calibration Management workflow offers a rich feature set to manage the entire lifecycle of your quality assets. With support for leading enterprise platforms it's perfect for deployment in the corner lab of a startup manufacturing facility or a multi-site international quality-driven operation. With the IndySoft exclusive process modeling engine, companies can re-configure the event-driven workflows with checkpoints, rule sets, and documentation at every point along the equipment path, ensuring assets are handled according to their exacting requirements.
-
Product
4-in-1 OSLT Calibration Kit, DC to 26.5 GHz, Type-3.5 mm (m) 50 Ohm
CK520A
-
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
Product
Electrical Calibration And Standards
-
Capable of calibrating a large workload of probes in the laboratory or monitoring environments on-site in the field, Fluke humidity probe calibrators and environment monitors are used where humidity and environmental measurement is critical. Proper humidity calibration is essential to prevent spoilage or damage to products in industries including data centers, pharmaceuticals, medical devices, semiconductors, chemicals, and food production. Fluke humidity calibration tools are dependable, accurate, easy-to-use solutions, with some having the ability to monitor additional environmental conditions such as temperature and barometric pressure in a single solution.
-
Product
Humidity Calibration
-
Capable of calibrating a large workload of probes in the laboratory or monitoring environments on-site in the field, Fluke humidity probe calibrators and environment monitors are used where humidity and environmental measurement is critical. Proper humidity calibration is essential to prevent spoilage or damage to products in industries including data centers, pharmaceuticals, medical devices, semiconductors, chemicals, and food production. Fluke humidity calibration tools are dependable, accurate, easy-to-use solutions, with some having the ability to monitor additional environmental conditions such as temperature and barometric pressure in a single solution.
-
Product
Calibration Software
-
Proper calibration means operating at peak performance with minimal downtime. But calibration adjustments can be time-consuming and difficult to schedule during regular operations. That’s why Fluke calibration software is designed to make calibration simple by automating the process as much as possible.
-
Product
Economy Mechanical Calibration Kit, DC To 6 GHz, Type-N, 50 Ohm
85032E
Mechanical Calibration Kit
The Keysight 85032E economy calibration kit contains a type-N male fixed termination and a one-piece type-N male open/short circuit. These standards are used to calibrate Keysight network analyzers for measurement of devices with 50 ohm type-N connectors. The kit is specified from dc to 6 GHz.
-
Product
Fixture Self-Test Controller and Calibration Check
AQ818
Test Fixture
The module AQ818 includes all the electronic blocks required to perform an effective test platform self-test. Thanks to this module, a chain of tests can be performed, which will end up not only with a report of the defective instruments or switch modules, but also with the relay contacts live expectancy report.
-
Product
VNA Calibration Kits
-
Vector Network Analyzers are commonly used to accurately determine the RF Characteristics of microwave components. Accurate Testing of microwave circuits means eliminating measurement errors and ensuring repeatable results. This is only possible when the network analyzers can be calibrated with known and true calibration standards.
-
Product
Calibration Light Source
CAL1
-
Image Engineering GmbH & Co. KG
The one light source solution in the field of camera characterization and calibration. CAL1The CAL1 calibration light source is designed to characterize and calibrate cameras in the lab or on the production line. Its compact design consists of one iQ-LED element in a 0.3 m integrating sphere that illuminates a 70 mm opening. Because of the non-reflective special diffusor filter on the sphere opening, a uniformity of more than 98% could be reached
-
Product
Photometric Ozone Calibrator
Model T703
-
Teledyne Advanced Pollution Instrumentation
The Model T703 is a microprocessor controlled ozone calibrator for precision gas analyzers. The Model T703 can deliver concentrations from 50 ppb to 5 ppm at flows from 1 LPM to 5 LPM.The Model T703 has two major components; the ozone generating device and the photometer. The ozone generator produces ozone by passing zero air over a UV lamp. Flow rate and lamp intensity are adjusted to deliver a specified ozone concentration by volume. The temperate and pressure compensated photometer, identical to that of the Model T400 ozone analyzer, provides feedback control of the UV lamp intensity, assuring stable ozone output. A nearly unlimited number of calibration sequences may be programmed into the non-volatile memory of the T703, covering time periods up to a year.
-
Product
Calibration Executive Software
CalEasy Series
-
CalEasy is a full-featured, Calibration Executive software package that supports the verification and calibration of Marvin Test Solutions instruments. The software is intended for use by users that prefer to perform in-house calibration and verification for their Marvin Test Solutions instruments. By calibrating or verifying the instrument in-house, the time and cost associated with returning an instrument to Marvin Test Solutions for calibration service can be eliminated or reduced. CalEasy is also used internally by Marvin Test Solutions production to perform initial calibration and to recalibrate the instrument when received for service. This ensures that user and factory based calibration performance is similar. Depending on the specific instrument, standards instrumentation supported for calibration / verification includes a DMM, and a frequency standards module. Some modules require the use of matrix switch card.
-
Product
Thermal IR Camera
LIR320
-
*LIR320 is the perfect system for IIoT and Machine Vision applications.*With a resolution of 320×240 pixels and state-of-the-art pixel pitch of 12 μm, it is offered with two optical options, 4 mm and 9.1 mm, giving you calibrated, high-quality thermal images, at a frame rate of 27 Hz.*The camera LIR320 is a cost-effective imaging solution that provides maximum performance in multiple industry applications.
-
Product
UV Analyzers
Model UV6
-
The Model UV6 Analyzers are a family of on-line sampling analyzers that use UV absorption to perform an analysis. The analyzers are configured to perform analysis over a wide range of values for each parameter measured, Nitrate, Color, or the correlation at 254 nm wavelength for COD, BOD or TOC. The UV6 Analyzers are easy to start up and use, simply connect the sample, waste and cleaning solution/reagent lines and then power up the Factory Calibrated analyzer. Wall mounting hardware is standard but an optional benchtop stand with reagent holder is also available. Accessing information or customizing an analysis routine are easily accomplished with the simple, user friendly menu structure and touch screen interface.
-
Product
Base for Optics Height Adjuster and Post
10784A
Mounting Panel
The Keysight 10784A Base provides a mounting plate for the 10785A Optics Height Adjuster and Post. The 10784A is an accessory complementing a family of measurement optics and lasers that constitute the 5530 Laser Calibration System.
-
Product
Humidity and Temperature Measurement Accessories
-
Find our selection of most frequently used accessories such as filter and filter carriers to protect your sensor against mechanical influences or a range of accessories for mounting, connecting, installation, maintenance and calibration of your humidity and temperature instruments.
-
Product
10 MHz To 6 GHz LAN Wide Dynamic Range Average Power Sensor
L2051XA
Power Sensor
Frequency range of 10 MHz – 6 GHzLAN connectivity with a wide dynamic range of -70 to +26 dBm for small signal measurementsFast real-time measurement of 50,000 readings/secReal-time measurement with zero dead time to ensure every single continuous pulse is measuredAverage mode time-selectivity function allows full dynamic range for average and time selectivity average power measurementsInternal zero and automatic calibration saves time and reduces measurement uncertaintyA BenchVue software license (BV0007B) is now included with your instrument. BenchVue makes it simple to connect, control instruments, and automate test sequences
-
Product
Optical Square
10777A
Accessory Kit
The Keysight 10777A Optical Square, used with Keysight straightness measurement optics, adds squareness measurement capability to the Keysight5530 Laser Calibration System. The optical square measures the squareness of axes during laser calibration of a machine tool. The Keysight 10777A uses two accurately-aligned mirrors to direct an output beam at precisely 90 degrees to an input beam.
-
Product
Universal Field Calibrater
UFC 45-B
-
Model UFC-45-B field calibrater is widely used calibration tool in process industry for last 15 years. Functionally it is designed to tackle most common trouble-shooting during commissioning and routine maintenance. Model UFC-45-B is truly hand held calibration instrument purposely limited functionally to simplify its use. With all its features UFC-45-B battery operated field calibrator is an essential tool in a service engineers kit.
-
Product
Ohm-Stat Guardian Pro Constant Monitor
-
Tests two people and two wriststrapsLED and buzzerNIST calibration includedWorks with all single wire capacitance wrist strapsAll cords suppliedCE markCan be calibratedProduct conforms to the ESD S.20.20 spec standards110v AC powerGround dock included
-
Product
Torque Meters
-
Torque meter is available in two different versions: handheld meters or tabletop meters. Torque meter have a wide range of applications. Handheld torque meter is mainly used for industry while tabletop torque meter is the ideal tool for laboratories. Our Torque meters come with a RS-232 port to transfer torque values to a PC or a portable computer. This is very helpful if you want to save the data and stand the chance to compare what you have measured afterwards. Another possibility is that you aim to do long-term-measurements. There the interface and the software are two very useful features that are given to you.Tabletop torque meters can be equipped with a printer (option). You can also order a ISO calibration certificate as an option. This ensures that the device has been calibrated and works perfectly including a measurement with only small deviances that can still be tolerated and do not influence the product's functions. We can offer you torque meters that can measure up to a maximum measuring value of 500 Nm.
-
Product
Monitor Calibrator
hueyPRO
-
It's all about the color. Color in your photos, color in your designs, color online and more importantly, color on your display. World's first built-in ambient light sensor enables consistency never seen before in any lighting condition.
-
Product
Enhanced Time Domain Analysis With TDR
S96011B
-
Use S96011B to perform enhanced time domain analysis for high-speed data applications. Includes all functionality of the S96010B (TDR/TDT mode). In addition, the S96011B enables more detailed measurements and evaluations, such as eye diagram / mask modes, without adding PLTS software. Jitter and emphasis / equalization capabilities enable simulation of real-world signals and environment. The S96011B covers up to 53 GHz bandwidth. Full calibration is available and the automatic deskew ensures easy removal of fixture and probe effects. To get the best accuracy, use mechanical calibration kits or ECal with DC option (i.e. N469xD or N4433D with Option 0DC).
-
Product
sbRIO-9215, Non-Enclosed, ±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Modul
780878-01
Voltage Input Module
Non-Enclosed, ±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The sbRIO‑9215 performs differential analog input. The sbRIO‑9215 contains NIST‑traceable calibration, a channel‑to‑earth ground double isolation barrier for safety and noise immunity, and high common-mode voltage range. Non-enclosed modules are designed for OEM applications.
