Force
exerts an influence.
See Also: Compression, Crimp Force, Pull Force, Pull off Force, Push Pull Force, Peeling, Tension, Gravity, Electrical, Magnetic
-
Product
Fingernail Test Probe
CX-Z11
-
Shenzhen Chuangxin Instruments Co., Ltd.
The Fingernail Test Probe is used to test to IEC 60335 and UL standards. It checks the security of parts that snap together. The spring loading in the handle can be calibrated to the force necessary to use the instrument. This probe is made of stainless steel with specially hardened tip and a Delrin?handle. Handle has a threaded hole for use with force gauges.
-
Product
48 Ω HMM Pulse Force Probe
PHD-HMM-48-1
-
High Power Pulse Instruments GmbH
*High current wafer-level and package-level 98 Ω HMM probing with grounded DUT*Built-in high surge 48 Ω pulse reflection suppression resistor up to 80 A peak*Fast rise time < 0.5 ns due to low inductance GND loop*Variable pitch from 50 µm to 5 mm*Tungsten replacement probe tips*SMA pulse force pigtail*Compatible to PHD-3001A interface*High reliability
-
Product
Extender
3690
-
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards. Receptacles have double row phosphor bronze contacts with high quality, long life mounted on top of the extender.
-
Product
Elongation Tester
SC-5
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.3-2008/IEC60851-3; Inspection standard: JB/T4279.3-2008Used to test elongation (ductility) of copper wires covered with φ0.100-3.0 mmenamel, silk or other insulation materials and other metal wires with tensile strength ≤2000N;Application of SCM control allows for fast operation and strong anti-interference capacity;Preset elongation of samples with two-digit toggle switch and, when the preset value is reached during test, motor and counter would automatically stop action and display results;The instrument is capable of measuring elongation while also the tensile force and holding the maximum tensile force value during stretching;Clamps are designed according to characteristics of various wires to prevent samples from breaking at clamp jaws, easy to load samples and, after samples are compressed, enamel can be automatically broken;While sample is broken, movable clamp would automatically stop moving, with error between displayed and actual elongation value less than 1%;
-
Product
Load Measuring Pins
-
Magtrol Load Measuring Pins are temperature-compensated transducers used to measure load and force and provide overload protection. The pins are mounted into machines in place of normal shafts and fitted with strain gauges, allowing them to produce a signal proportional to the measured load.
-
Product
Cellular Network Analysis Software
NESTOR
-
R&S®NESTOR is a Windows 10 based platform for analyzing cellular networks via the air interface. It is deployed by law enforcement agencies, intelligence services, armed forces and regulatory authorities. R&S®NESTOR is used together with R&S®TSMX mobile network scanners and QualiPoc smartphones, which offer the most advanced technology worldwide. The software supports all relevant applications that public authorities and security organizations need to gather information about cellular networks. R&S®NESTOR is used in vehicles, trains, aircraft, drones, on ships and on foot.
-
Product
Performance Exams
-
Sturdy sheet steel housing with safety door and electrically driven base with built-on sample mold. The compaction takes place via a rolling segment with force / path-controlled drive device from above. The sample mold and the rolling segment are equipped with software controlled heating. The measurement of force and displacement is done by electronic sensors. The entire compaction process is controlled with Windows software and PC via preselected sequence programs.
-
Product
Squeak & Rattle Sub-System And Component Testing
-
At MB Dynamics, we’re proud to provide clients in a wide range of industries with quiet, custom turnkey component testing systems for combined squeak & rattle testing as well as durability testing of different components and subsystems (in 1 to 6 DOF). Test items can be excited in one or more axes to understand and characterize the physics and root causes of BSRs. Real-world, on-road vibration conditions are multi-axis simultaneous – vertical, fore-aft or longitudinal, lateral, roll, pitch, and yaw – 6 degrees of freedom or 6 DOF. Affordability drives decisions to find BSRs by exciting in one or two – fewer than 6 DOF. That has been a driving force for MB – be effective at finding BSRs with a lesser number of shakers (DOFs) and thus reduce the test equipment cost of finding BSRs. Vertical-only can be effective; sequential vertical then fore-aft then lateral is one step closer to real-world; creating vibration in four or five axes of response simultaneously is even closer; and full 6 DOF systems that are quiet come closest to duplicating in the lab the on-road conditions. MB offers all these possibilities to meet trade-offs of budget, test time, road replication, and BSR detection effectiveness.
-
Product
Closing Force Meter
-
Maschinenbau Haldenwang GmbH & Co. KG.
Is used to conveniently and reliably determine the closing force of externally operated service doors and locking devices.
-
Product
Verification Of Maximum Withdrawal Force Test Apparatus
IEC60884 FIG 18
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 FIG 18 verification of maximum withdrawal force test apparatusThis device complies with the requirements of GB 189.1-2008 Figure 18/19, IEC884 Figure 18/19, VDE0620, etc. It is suitable for checking the maximum force required to pull the plug out of the socket and the single pole pin pulled out from the socket assembly. Whether the minimum force required is within the range specified by
-
Product
XCITE 1100-5 Inertial Mass Excitation System
-
The 1100-5 Inertial Mass Modal Excitation system allows the testing of structures where backup fixturing is not available or possible. Accelerating an internal mass with the closed loop hydraulic excitation system generates the inertial forces. The compression control of the Xcite Master Controller maintains a constant force over a frequency sweep by continuously altering the drive signal to maintain the required dynamic force level.
-
Product
Compact Hydraulic Vibrator Force Simulator
JF Series
-
The JF Series Force Simulator was developed with the emphasis on light weight, compact size and ease-of-use as a general-purpose, compact jack for the Servopulser system. Testing systems installed with the Force Simulator can easily perform endurance, fatigue and simulation tests on small structural members and various other structural members, which helps improve the logical design and reliability of products.
-
Product
Atomic Force Microscope
XE-PTR
-
Park Systems' PTR Series is a fully automatic industrial in-line AFM solution for, but not limited to, automatic Pole Tip Recession measurements on Rowbar-level, individual Slider-level, and HGA-level sliders. With sub-nano scale accuracy, repeatability, and throughput, the PTR Series is the metrology tool of choice for Slider manufacturers to improve their overall production yield.
-
Product
Atomic Force Microscope
NX-Hivac
-
Park NX-Hivac allows failure analysis engineers to improve the sensitivity of their measurements through high vacuum Scanning Spreading Resistance Microscopy (SSRM). Because high vacuum scanning offers greater accuracy, better repeatability, and less tip and sample damage than ambient or dry N2 conditions, users can measure a wide range of dope concentration and signal response in failure analysis applications.
-
Product
Occlusal Analysis with BiteForce DynamicsTM
T-Scan
-
The T-Scan is a diagnostic device that measures relative biting forces, including occlusal force, timing and location and is an ideal complementor to articulating paper. The technology was invented by Dr. William Maness in 1987 at Tufts University and M.I.T.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type L, Ø1.50mm, 305gf
K100-L150305-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style L, Tip Diameter Ø1.50mm, Spring force 305gf, Steel with Gold Plating.
-
Product
Static Axial Clip-On Extensionmeters
2630-100 Series
-
The Instron static axial clip-on extensometer delivers precise strain measurement for static tests by quickly clipping to specimens (metals, plastics, composites) with minimal attachment force. Its rugged cross-brace design resists distortion, includes built-in over-extension protection, and meets ASTM E83 / ISO 9513 standards — making it a reliable, high-accuracy option for general and temperature-controlled testing.
-
Product
Real Car Transient Test System
RealCar Simulation Bench
-
This system is suitable for transient test of actual vehicle in combination with the real-time model calculation by the measurement/control panel and low inertial motor. By replacing the wheel of the actual vehicle with the tire type bearing, the axle shaft is taken out to the outside of the vehicle and connected to the low inertia motor. It can be reproduced the sliding motion which the chassis dynamometer cannot be realized. Also, since the longitudinal force is not occurred in the vehicle, the vehicle restraint can be simplified and the behavior such as shift shock can be reproduced on the bench.
-
Product
Milling Tool Dynamometer
-
Unitech Scales And Measurements Pvt. Ltd
Unitech offers tool dynamometers to measure cutting forces on various machines like lathe, drill, milling machines. All three direction forces are measured simultaneously and displayed. Tool dynamometers are useful to study, analyse the optimum feed, speed and depth of cut on different materials. The dynamometers are also available in various capacities as per customer requirement.
-
Product
Walking Drive
N-331 PICMAWalk
-
Physik Instrumente GmbH & Co. KG
OEM Walking Drive for Durable Applications with up to 15 mm/s Velocity and up to 50 N Push/Pull Force. The PICMAWalk walking drive combines the high reliability of the PICMA® actuators with the innovative stepping principle of the already established NEXLINE® and NEXACT® drives. Eight actuators arranged in the shape of a V ensure reliable and the highest possible feed motion with a maximum of 60 N holding force, 50 N push/pull force, and a maximum of 15 mm/s velocity.
-
Product
Double-Roller Dynanometer
R 100/1 | VP 230002
-
Maschinenbau Haldenwang GmbH & Co. KG.
The double roller dynamometer R 100/1 with eddy current brake on the right side of the vehicle and pneumatic lifting beam is designed to measure the performance of cars and stands out due to its extremely robust, durable and low-maintenance construction. The R 100/1 ensures highest measuring accuracy due to the power measurement at a constant rpm, speed or tractive force, including the drag power measurement. Operating methods such as load simulation, including optional modules for the measurement of external data, are possible.
-
Product
Force Sensors
-
Piezoelectric force sensors, respectively piezoelectric force transducers or load cells, are perfectly suited for the precise measurement of compressive and tensile forces, both in highly dynamic applications and in quasi-static processes. In universities and industry, for basic research or quality assurance: exact data is always essential in order to measure force characteristics and make processes more cost-effective. Thanks to their rugged design, piezoelectric force sensors from Kistler keep precise track of quasi-static and highly dynamic force processes, even when conditions are difficult. Our force sensors can also handle simultaneous measurements of multiple orthogonal force components.
-
Product
Force Sensors
-
Here at Flintec, our force sensor range provides solutions that integrate effectively into a wide variety of industrial applications. They include customized load pins, extensometers, torque sensors and a range of miniature force sensors.
-
Product
Light 0.83 (24.00) - 2.00 (57.00) High Performance Lead Free Probe
LFRE-1I35-2
ICT/FCT Probe
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
High 1.73 (49.00) - 8.00 (127.00) High Performance Lead Free Probe
LFRE-1T30-8
ICT/FCT Probe
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Brinell Hardness Tester
-
Sinowon Innovation Metrology Manufacture Ltd.
◆ Equips with OS Win10, and already installed BrinScan V3.0 Auto Brinell Measurement software.◆ Apply vision measurement technology, one key operation, realize auto loading, dwell, unloading and indentation measurement.◆ AutoBrin AB-3000V can display data statistics, hardness conversion, limitation setting, graph, measurement mode setting, etc.◆ Loading by high accuracy force sensor , and can compensate force loss during loading by micro central processing unit.
-
Product
Electrodynamic Shaker Systems
-
Electrodynamic shaker systems and amplifiers from MB Dynamics help to support a wide range of general-purpose vibration test requirements. The electrodynamic shaker systems are offered in a variety of force ranges, from 100N (25 lbf) to 22kN (5,000 lbf). The innovative design of MB Dynamics PM-Series electrodynamic shakers incorporates permanent magnet technology and the voice coil principle to create vibration. These heavy-duty electrodynamic shakers feature a robust design for maximum reliability, with end-users reporting a useful service life of 10, 25 or even 40 years! The shakers come in five unique sizes, with peak sine force ratings of 100 N, 200 N, 500 N, 1000 N and 2000 N; or, 25 lbf, 50 lbf, 100 lbf, 250 lbf and 500 lbf. The MB Dynamics C40HP electrodynamic shaker outputs 22 kN or 5,000 lbf peak. The C40HP is a part of the legacy C-Series of shakers, which have served as the foundation for today’s modern electrodynamic vibration test equipment industry.
-
Product
ICT Probes
Merica Series-MPAL50
-
Minimum Center: 1.27(50mil)Current Rating: 3amps, continuousCurrent Resistance: 60milliohmsFull Stroke: 6.35mmRated Stroke: 4.30mmSpring Force: 185/227gf(7/8oz)
-
Product
Inclined Impact Testers
-
Inclined impact testing simulates environmental dynamic forces that packaged goods may endure throughout transport and handling operations. These hazardous dynamics are simulated using impact test systems. Inclined impact test systems utilize a carriage that propels the test sample down a ramp at predetermined velocities before impacting into a fixed backstop. The specimen’s reaction to these extreme conditions indicates how the product would fare in real-world supply chain settings, allowing design engineers to make improvements to either the product and/or the protective packaging as needed.
-
Product
Radiation Force Balance
-
Radiation force balance for diagnostic and therapeutic medical ultrasound
