Product

5-Watt Broadband Transmitter

Loc3 5W

-

Vivax-Metrotech Corp

Loc3 5W - Vivax-Metrotech Corp

The 5-Watt broadband transmitter has selectable induction and direct connection frequencies from 98Hz to 200kHz, SD mode (Signal Direction), fault find and true resistance measurement up to 1 Mohm. The two inch by one-inch dot matrix display with LED backlight shows output current, connection type, volts, resistance, frequency, volume, battery condition and high voltage warnings.

Product

Variable Attenuator

VAXE

-

Elmika

VAXE - Elmika

The VAXE Variable Attenuators are waveguide components for tunable signal leveling or reflection compensation in waveguide networks. The Attenuators consist of waveguide section with a resistive film evaporated on the mica surface. The Attenuators has 0 ÷30 dB minimum attenuation range. The VAXE Attenuators are available in four waveguide bands between 33 GHz and 170 GHz.

Product

Micro-Ohmmeters

-

AMPTEC RESEARCH

AMPTEC RESEARCH

Micro-Ohmmeter is an affordable 7 range, 4-Wire Kelvin based product that is used to test electrical resistance on a wide variety of applications including winding resistance, contact resistance, and component testing. The 720A micro-ohmmeter has an autorange feature (available with NSN package) and is compatible with an RS232C interface (OP-232). Thanks to its wide-range capabilities, ease of use, and CE mark, this micro-ohmmeter is used commonly across the globe.

Product

Premium 4.49 (127.00) - 12.00 (340.00) High Performance Lead Free Probe

LFRE-25H-12

-

ECT

LFRE-25H-12 - ECT

Current Rating (Amps): 8Average Probe Resistance (mOhm): 8Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02

Product

Current, Voltage, Resistance

-

Mensor Corp.

Mensor Corp.

Solutions for the testing and calibration of current, voltage and resistance are used in industry (laboratories, production, workshops), in calibration service companies and in quality assurance. These instruments are portable and mobile and are particularly notable for their low measurement uncertainty and high scope of operation.

Product

Corrosion Testing

-

Global Testing Services Inc.

Global Testing Services Inc.

The salt spray test is a standardized test method used to check corrosion resistance of coated samples. Coatings provide corrosion resistance to metallic parts. Since coatings can provide a high corrosion resistance through the intended life of the part in use, it is necessary to check corrosion resistance by other means. Salt spray test is an accelerated corrosion test that produces a corrosive attack to the coated samples in order to predict its suitability in use as a protective finish.

Product

Humidity and Temperature

Humidity wood

-

PASI srl

Humidity wood - PASI srl

The BM15 moisture meter, which is incredibly easy to use, is ideal for the quick and reliable determination of the moisture content of wood and building materials using the resistance principle. The T510 is a professional hand-held measuring instrument for the precise determination of the moisture content of wood and materials using the resistance method.

Product

Miniature Concentric Ring Set

PRF-912B

-

Prostat Corporation

PRF-912B - Prostat Corporation

- Measures Surface Resistance from 0.9Ω to 1.0x1012Ω- Approximates Measurements Typically Obtained when using ANSI/ESD STM11.11- Spacing Allows for Measurement Area of 0.32 inches (8.13mm)- Spring Loaded Center Electrode Surrounded by 10 Contact Electrodes- Includes Conductive Rubber Covers- Certificate of Calibration Traceable to NIST included

Product

Passive Probes

-

Teledyne LeCroy

Teledyne LeCroy

Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a /10 attenuation and feature a high input resistance of 10 MOhm. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400 V, some as high as 600 V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.

Product

Resistivity Test System

RMS-1000

-

ECOPIA

RMS-1000 - ECOPIA

Accurate and powerful performance. - Possible to get much accurate resistivity value by taking 8 raw data. - Good to check ohmic contact by flowing forward and reverse current.2. We provide various sample mounting board and probe head and tips.3. We have an optional item which can measure in variable temperature. - Room Temperature ~ 300dC.

Product

Tap Changer Analyzers & Winding Ohmmeters

-

IBEKO Power AB

IBEKO Power AB

Winding resistance test of inductive test objects, such as power transformers, is one of the most effective non-intrusive ways of checking its condition. Due to their advanced design, DV Power winding resistance meters provide high test currents (up to 100 A DC) and high accuracy (up to 0.1%) within light and portable test instruments. In addition to winding resistance measurement, it is also possible to perform simple, quick and reliable transformer on-load tap changer condition assessment by recording the test current during tap changer operation, also known as DVtest. Because of that, problems with a tap changer connection, contacts, and switching procedure can be detected.DV Power winding ohmmeters consist of single-phase RMO-T and three-phase TWA series. Models from the TWA series are designed for six-winding resistance measurement of power and distribution transformers, with only one single-step cable setup. As a result of reducing the total test time, it enables significant saving of time and money.Typical application areas of these instruments are high-voltage substations and industrial environments. They are intended to measure the resistance of:Transformer windingsOn-load tap changersGeneratorsElectrical motorsHigh-current bus bar jointsCable splicesWelding joints

Product

MINI Data Logger for Temperature and Humidity

MINI-TH(Medical type)

-

ZOGLAB Microsystem Co., Ltd.

MINI-TH(Medical type) - ZOGLAB Microsystem Co., Ltd.

Large-screen display of temperature and humidity, with battery, memory , recording status show together· High precision, mass memory for long-term logging· Free of toxicity and halogen as FDA / HACCP / ISO22000 require· Resistant to water and dust, suitable for cold chain systems of fresh food, fruit, vegetables or wine

Product

Salt Spray Corrosion Test Chamber

CX-Y60L

-

Shenzhen Chuangxin Instruments Co., Ltd.

CX-Y60L - Shenzhen Chuangxin Instruments Co., Ltd.

Laboratory Salt Spray Corrosion Test Chamber for Nss / Acss / Cass Test is used to test the anti-erosion quality of the surface of all materials after the rust-proof of painting, coating, electroplating, anoding and rust-proof of greasing.anti corrosion treatment for a variety of materials, corrosion resistance of their products.

Product

Planar-Doped Barrier Diode Detector, 0.01 to 50 GHz

8474E

-

Keysight Technologies

8474E - Keysight Technologies

The Keysight 8474E is a high-performance detector using a gallium arsenide, planar-doped barrier detecting element. It features extremely flat frequency response over its entire band of operation and very good frequency response stability versus temperature. The Keysight 8474E is also very rugged with high resistance to ESD damage. The Keysight 8474E detector is available with a 2.4-mm (0.01 to 50 GHz) connector. This detector offers the options for optimal square-law loads (Option 102) and for positive polarity output (Option 103). Because the unit-to-unit frequency response tracking of this device is typically better than plus or minus 0.3 dB, no matched response option is offered.

Product

On Load Tap Changer Analyzer

TAP-4-PLUS

-

Zensol Automation Inc.

TAP-4-PLUS - Zensol Automation Inc.

The Tap-4-PLUS is the newest instrument by Zensol for OLTC testing. It has 2 more analog inputs than the TAP-4. The TAP-4-PLUS with the TAP-DRM accessory can perform dynamic resistance, vibration, and motor current recordings at the same time. Doing so will allow you to easily understand the vibration impacts.

Product

Modbus RTU Analog Input Modules

-

Datexel

Datexel

The Datexel range of Modbus RTU analog input cards for both RS485 and RS232 with Modbus or ASCII protocol can be combined with the DAT9000 series of Modbus Masters. A choice of input cards or modules are available and have various optional inputs such as Voltage, Current, Thermocouples, RTD, and Resistance. Also a choice of 2, 4, 8 channel options are available. The DAT3011 is a Modbus RTU Slave with 1 selectable universal input (Thermocouples, RTD, mV, RTD's or Resistance), 2 x 4-20mA or 0-10V input and 2 x4-20mA outputs. The DAT3011 also has 3 digital inputs and 3 relay outputs. Each module is isolated from each other and is set up using the DAT3000 software Development package which is free of charge from the Datexel download web page. Datexel also has universal input modules. An 8 channel analog input card is available making the DAT3000 series a very economical solution to large and small scale Data Acquisition. Combining these analog input cards with the analog output cards, the digital input/output cards and the communication devices make Datexel the smart choice where Data Acquisition is required.