AC DC Clamp Meters
measure AC-DC amperage without contacting conductors.
See Also: AC/DC Current Probes
-
Product
600 Amp DC / 400 Amp AC Current Probe
DC600
-
Can measure from 5 to 600 Amps DC current for most industrial DC measurement jobsNo batteries required, because power is supplied by PowerSight. This means that the probe will not stop during a long monitoring session.
-
Product
AC Power Sources
-
Chroma Systems Solutions, Inc.
AC Power Supplies designed to satisfy both automated test system and laboratory benchtop requirements.
-
Product
DC Block
-
RF Lambda’s DC blocks are used to prevent DC signals from passing through a coaxial RF interface. They are low IL and wideband.
-
Product
DC Blocks
-
Coaxial DC Blocks allow the transmission of RF signals while blocking DC signals, usually using a blocking capacitor. We feature SMA DC blocks, 2.92mm DC Blocks, 1.85mm DC Blocks, BNC DC Blocks, TNC DC Blocks, and Type N DC Blocks. DC blocks can block the inner conductor, outer conductor, or both; hence there are "inner" dc blocks, "outer" dc blocks, and "inner/outer" dc blocks. These Coaxial DC Blocks are frequently used in Satellite Systems where a control voltage is passed along with the RF signal, and the coaxial dc block protects equipment. The BNC DC block uses a precision bnc to get to 4ghz. The C0927 SMA DC Block uses dual parallel capacitors to achieve its broad bandwidth, its ideal for EO & NRZ systems.
-
Product
Resolver to DC Sine / Cosine or Synchro to DC
ST-RD & ST-SD
-
Computer Conversions Corporation
ST-RD and ST-SD Series - Resolver to DC Sine / Cosine or Synchro to DC Sine Cosine Packaged on PCB with Track and Terminal Block and On-Board AC Reference Supply may be used driving DC Servo amp in active position synchronizing applications
-
Product
AC Calibration Standard
1U647-001
-
The 1U647-001 is a low cost calibration standard used to determine if a 1U632-100 or a 1U663-100 DMU requires factory calibration. Its portability makes it ideal for field-testing. The standard generates signals that simulate the aircraft’s resolvers, rotary variable transformers (RVTs), and linear variable displacement transformers (LVDTs). The unit also generates a pulse width modulated (PWM) signal, and routes the output of an ARINC 429 source to the different DMU input channels. The calibration standard connects directly to the DMU and replaces the output signals of an active extender card. Discrete switch settings simplify testing. The unit is housed in a rugged aluminum case.
-
Product
600A TRMS Clamp Meter w/ DC Amps, Inrush, Magnet
DL589
-
UEi Test & Measurement Instruments
True-RMS Dual Display 600A Clamp Meter w/ DC Amps & Differential
-
Product
Clamp type AC Current Sensor／for Low Leakage Current Measurements(ZCT Series)
ZCT-18
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Best sensor for low leakage current measurements of less than 1mA.*Ultra compact size with 18mmφ jaw opening capability.*High sensitivity and least affection from external magnetic field.
-
Product
AC Power Source
AFC series
-
The AFC Series is an economically priced AC power source to provide reliable voltage and frequency simulation for general applications, such as testing for home appliance, electronic, medical equipment, lighting and other fields of production or R&D. Utilized PWM switching technology, AFC provides high quality pure sine waveform with output level up to 2,000kVA. The AC source is coupled with output voltage range of 5~300V and output frequency of 47~63Hz, 50/60Hz fixed. User can select optional frequency output of 2 or 4 times standard frequency and 400Hz.
-
Product
AC/DC CAT IV 600 A TRMS Navigator Clamp Meter
ACDC-52NAV
-
The ACDC-52NAV clamp-on power meter is the ideal choice for jobs that require AC/DC current measurements to 600 A, AC/DC voltage to 1000 V and wide jaws to accommodate large conductors.
-
Product
Power Cord, AC, U.S., 120 VAC, 2.3 Meters
763000-01
Power Adapter
Power Cord, AC, U.S., 120 VAC, 2.3 meters
-
-
Product
AC Reference Generators
SRB
-
Computer Conversions Corporation
The SRB Series are miniature, Bulk-head Mount, low cost AC reference generators to supply moderate power 2-115VAC excitation to Synchro's, Resolvers, LVDT's and related converters in COTS-Military and industrial applications for measurement, control, simulation and data communications.
-
Product
Analog AC Leakage Current Clamp Tester
MCL-350
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*High accuracy analog display with strong taut band meter.*3 years long battery life.*Meter lock function and data output for recorder.*Filter rejection for high frequency noise
-
Product
Digital Clamp Tester (CE)
M-2100
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Wide current measurements with tear drop type 55mmφCT up to 2000A.*Data-hold and Auto power off function.*Additional AC/DC voltage, resistance, diode test, continuity check.*Conform to IEC safety requirements.
-
Product
Capacitor for AC Filtering
PECA4 (440V)
-
Lifasa - International Capacitors, SA
These capacitors are especially suitable for applications where high levels of AC voltage are required. The design of this series has been optimized for the manufacture of high performance AC filters for compensation equipment with high pollution such as UPS or wind turbines.
-
Product
1000A Power Quality Clamp Meter with Temperature
ACD-41PQ
-
The Amprobe ACD-41PQ provides a simple and effective way to verify if the electrical system is affected by harmonics. Add on troubleshooting capabilities with the ACD-40PQ data-logging feature or get complete power analysis with the ACD-41PQ. Increase measuring efficiency with an optional PC interface kit.
-
-
Product
AC & DC Electronic Loads
-
The Adaptive Power Systems Electronic Loads cover a wide range of power levels, voltage and current profiles and feature sets.Supported voltages range up to 1250Vdc or 350Vrms AC. From bench to system and DC or AC requirements, we can more than likely offer you the optimal programmable load to meet your needs.
-
Product
Flex Clamp Meters
-
*Flex Clamp Current Probes expand existing meters *Compatible with most meters using universal banana leads*Flexible Coil adds accessibility - easily maneuvering around cables that are in hard to reach areas and large enough to thread around larger conductors
-
Product
Combinated Current Clamps
-
PeakTech Prüf- und Messtechnik GmbH
Measure small direct and alternating currents up to 2 A with 1 mA resolution. The device measures the current indirectly via the surrounding magnetic field, so it is measured without contact when the clamp jaws enclose the current-carrying conductor (single wire).
-
Product
Meter
TruFlow™
-
TruFlow meters help improve production efficiency and product quality by enabling simple, cost-effective material flow measurement. This is a crucial first step in the OptiBond™ variation management process of measure, understand and improve material delivery and dispensing.
-
Product
AstroAI Digital Clamp Meter
-
Check out our VIDEO on the left side and take a quick tour of AstroAI Multimeter! TEST A WIDE RANGE of measurements including AC/DC Voltage, AC Current, Resistance, Continuity; Also Tests DiodesQUALITY DESIGN features a sampling speed of 2 times per second; Auto off conserves battery life and increases the lifespan of your multimeter
-
Product
Advanced Power System - DC Power Supply, 20 V, 100 A, 2000 W
N6971A
DC Power Supply
The N6971A is designed for automated test equipment (ATE) applications where high performance is critical.
-
Product
Clamp type AC Current Sensor／for Low Leakage Current Measurements(ZCT Series)
ZCT-110S
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Best sensor for low leakage current measurements of less than 1mA.*Suitable for low current measurements of terminal feeder.*High sensitivity and least affection from external magnetic field.
-
Product
Regenerative Power System, 80 V, ±125 A, 5 KW, 400/480 VAC
RP7942A
DC Power Supply
The Keysight RP7942A regenerative power system is a single output, bi-directional, regenerative DC power supply with highly integrated safety features that protect both your people and your device under test.
-
Product
High Accuracy Clamp Leaker
-
Leakage Current Clamp Meter, Car Standby Current Clamp Meter, Car Inrush current Tester, Car Charge Current Tester. It is specially designed for online measurement of AC/DC leakage current, current below 600V by adopting up-to-date CT technology and digital integration technology. It is especially suitable for measure car standby current, leakage current, inrush current. It is a product with the characteristic of relatively small size, high accuracy, strong anti-interference capability and automatic shifting.
-
Product
Earth Ground Clamp Meter
T2000
-
T2000 is a professional clamps specially developed to evaluate resistance of earth rods with no need to disconnect any part of the system (STAKELESS METHOD)
-
Product
AC Source
5310（0~500Vrms/1KVA）
-
Voltage output has totally six ranges，maximum up to 500V，convenient for 300V above the voltage regulation test
-
Product
AC Current Clamp Meter
3280-10F
-
AC Current Clamp Meter with Broad Operating Temperature Range, Attachable Flexible Sensor, and Drop-Proof Durability
