Analog Input Output
Analog I/O are Devices that have the capability of sending and receiving analog signals.
-
Product
ASI/SD-SDI Input+output With Relay Bypass For PCIe
DTA-2145
-
General-purpose DVB-ASI input and output, also SD-SDI capable. A relay automatically connects input port to output port upon software- or hardware failures, enabling highly-available system configurations without requiring a failover switch.
-
Product
NI-9216, 8-Channel, 400 S/s Aggregate, 0 Ω to 400 Ω, PT100 RTD C Series Temperature Input Module
783863-02
Temperature Input Module
8-Channel, 400 S/s Aggregate, 0 Ω to 400 Ω, PT100 RTD C Series Temperature Input Module - The NI‑9216 is a resistance temperature detector (RTD) input module. You can configure the NI‑9216 for two sample rate modes: high sample rate or high resolution. The NI‑9216 is compatible with 3‑ and 4‑wire RTD measurements, and it automatically detects the type of RTD (3-‑or 4‑wire) connected to the channel and configures each channel for the appropriate mode. The module provides per channel current excitation. The NI‑9216 features calibration and includes a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and a high common-mode voltage range.
-
Product
Analog I/O Interfaces
-
United Electronic Industries, Inc.
24 differential analog input channels Maximum sampling rate of 1000 Hz per channel 18-bit resolution ±3 µA accuracy 350 Vrms Isolation Dynamic autozero support Embedded averaging engine
-
Product
Analog Seismic Sensors
Seismometers
-
Designed to yield the performance needed for scientific studies, our seismometers are used for monitoring long period (very low frequency) signals. These units are often used for earthquake monitoring and for triggering potential alerts during natural disasters such as tsunamis.
-
Product
Isolated Input Card
mPCIe-II-16
-
The mPCIe-II-16 consists of a type F1 PCI Express Mini Card (mPCIe) interface board that connects to a Mobile-ITX-sized, DB-37M Isolation Module via an included 9” cable. That module is designed to be easily panel-mounted in any application environment. It uses the high speed PCI Express bus to transfer digital data to and from the card. The digital I/O is compatible with 8255 PPI chips making it easy to program.
-
Product
sbRIO-9213, Non-Enclosed, 16-Channel, 75 S/s Aggregate, ±78 mV C Series Temperature Input Module
781210-01
Temperature Input Module
Non-Enclosed, 16-Channel, 75 S/s Aggregate, ±78 mV C Series Temperature Input Module - The sbRIO-9213 is a high-density thermocouple input module that is designed for higher-channel-count systems. With this module, you can add thermocouples to mixed-signal test systems without taking up too many slots. The sbRIO-9213 includes anti-aliasing filters, open-thermocouple detection, and cold-junction compensation for high-accuracy thermocouple measurements. The sbRIO-9213 features NIST-traceable calibration and a channel-to-earth ground double isolation barrier for safety, noise immunity, and high common-mode voltage range. Non-enclosed modules are designed for OEM applications.
-
Product
500W - Single Output
XMS500 Series
-
*ITE & Medical Certifications (2 x MOPP)*Class I & Class II operation with Level B EMC*Compact 4 x 7.1" footprint*Suitable for B and BF rated equipment*Five year warranty
-
Product
8 Relay Output Board, 8 Isolated Digital Input Channels, 24V
APCI-2200-8-8
-
*8 relay output channels*Switching voltage 60 V/DC, 48 V/AC, switching current 1 A*8 digital input channels, 24 V*Optical isolation*Watchdog*Easy programming
-
Product
12-bit, 100KHz, 16SE/8DIFF Isolated Analog Input Board
APCI-3001-16
-
16 single-ended or 8 differential inputs 12-bit resolution Optical isolation 500 V 100 kHz data transfer rate Automatic analog acquisition 8 digital I/O, 24 V, isolated, timer Trigger functions Graphical display of the measured data
-
Product
Analog Oscilloscope
PS-251
-
*25MHz, ALT Trigger.*1mV sensitivity.*10ns Resolution.*Component test, Beam-finder*Illuminate, Hold-off, X-Y
-
Product
Analog Sequencers
-
Analog sequencers from Analog Devices integrate accurate comparators with the control functionality of power-on and power-down sequencing for voltage regulator banks. The comparators monitor the regulator voltage outputs and trigger the turn on of next rail in the system after a preconfigured time delay. Some members of this portfolio can be cascaded together, which provides scalable solutions to expand functionality across multiple devices. Our analog sequencers provide an easy to use solution for power sequencing challenges in cellular infrastructure, telecommunication, data communication, and data center applications.
-
Product
Analog Panel Meter
-
Wuxi IMHOO Technology Co., Ltd.
A mechanical, electro-mechanical instrument that displays real-time electrical measurements using a moving pointer (needle) on a calibrated scale.
-
Product
GPIB Analog Interfaces
-
ICS's GPIB to Analog Interfaces are designed to provide isolated analog and digital drive signals to control power supplies and other devices. Optional isolated Analog inputs. Available in rack mountable Miniboxes™ and OEM board versions. All of ICS's GPIB to Analog Interfaces are fully IEEE-488.2 compliant and HP-IB compatible.
-
Product
Temperature Input Device
-
The Temperature Input Device is a thermocouple measurement device featuring InstantDAQ technology. InstantDAQ technology includes built-in software for viewing and logging data that automatically loads when you plug in the device, so you can instantly take temperature measurements with your PC. You can connect the Temperature Input Device to any USB port to use your PC as a display and monitor data in real time. The device is compatible with J, K, R, S, T, N, E, and B thermocouples.The Temperature Input Device includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
-
Product
Hall-Sensor Board with analog output
041-970
-
The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
Product
15W to 60W - Single Output
KMS-A Series
-
*Medical Safety Cert (4kVAC In-Out)*Class II (No ground needed)*Wide Temperature Range*Low off-load power draw*High Efficiency*Small size and lightweight
-
Product
NI-9375, 30 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module
781030-02
Digital Module
30 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module - The NI‑9375 is a digital I/O interface that works with industrial logic levels and signals for direct connection to a wide array of industrial switches, transducers, and other devices. Each digital input line is compatible with 24 V logic levels, and all the output lines are compatible with 6 V to 30 V signals, based on the external power supply. The NI‑9375 offers isolation between the input and output banks from channel‑to‑earth ground.
-
Product
Transducers with 4-20 mA Output
-
Transducers / transmitters for temperature, humidity, atmospheric pressure and CO2 with 4-20mA interface.
-
Product
NI-9215, ±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
779011-01
Voltage Input Module
±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9215 performs differential analog input. The module contains NIST-traceable calibration, a channel‑to‑earth ground double isolation barrier for safety and noise immunity, and high common-mode voltage range. It is also offered in two connectivity variants: 10‑position screw terminal or BNC.
-
Product
Batch Controller (pulse input)
-
A low-cost controller for repetitive fill operations. The typical application utilizes a flow meter input and two built-in relays: a Prewarn relay slows down the pump near a preset to avoid overshoot and a Batch relay stops the pump at the preset.
-
Product
4-Ch, 16-Bit Isolated Analog Output EtherCAT Remote I/O Module
AMAX-4820
EtherCAT Motion Module
Suitable for EtherCAT networks4-ch, 16-bit analog output channels with 2,500 VDC isolationVoltage or current output with multiple rangesQuick removable European type connectorSupports EtherCAT Distributed Clock (DC) mode and SyncManager modeTwo rotating switches for up to 256 slave IDs
-
Product
16-bit, 200KHz, 16SE/8DIFF Isolated Analog Input Board
APCI-3016-16
-
The APCI-3016 is a 16-bit analog input board for 3.3 V and 5 V PCI systems, with optical isolation and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.
-
Product
JFET Input Amplifiers
-
Analog Devices JFET input op amps or FastFET high speed (>50 MHz) input op amps provide high input impedance and ultralow input bias currents for high speed applications. The majority of our FET input op amps feature wide supply ranges from +5 V to 12 V or higher and feature rail-to-rail outputs enabling wide dynamic range.
-
Product
5W to 26.4W - Single Output
KWS-A Series
-
*-40°C (start up) to +85°C operation*Low off-load power draw (<0.5W)*Improved efficiencies up to 88%*Class II, No Ground Connection*Long Electrolytic Capacitor Lifetime*Compact Size*No external components needed
-
Product
8-Ch, 16-Bit Isolated Analog Input EtherCAT Remote I/O Module
AMAX-4817
Analog Input Module
Suitable for EtherCAT networks8-ch, 16-bit analog input channels with 2,500 VDC isolation±275 V high common-mode voltage rangeQuick removable European type connectorSupports EtherCAT Distributed Clock (DC) mode and SyncManager modeTwo rotating switches for up to 256 slave IDs
-
Product
250W - Single Output
RGA Series
-
*1/16th Brick Footprint*9-40 Vdc, 9-53 Vdc Inputs*3.3 up to 40 Vdc Outputs*Up to 20 A max Output Current*Non-Isolated Step-Down*-40 to 110 °C Case Temperature*Rugged 5-sided Aluminum Case
-
Product
32 Input, 32 Output USB Modular Digital I/O
U2651A
Digital I/O Module
The Keysight U2651A USB Digital I/O is a cost-effective device with its offering of 64 opto-isolated digital lines. It comes bundled with the Keysight Measurement Manager (AMM) software for quick set up and data logging. Simplifying this further is the command logger function offered in the Keysight Measurement Manager that allows capturing of configuration commands that can be easily converted to snippets of VEE code. Other supported languages are VB, C++, and C#.
-
Product
Analog Oscilloscope
PS-605
-
VERT. SENSITIVITY FROM 1mV/DIV TO 15V/DIV. SWEEP RATE FROM 10NS/DIV TO 1S/DIV. COMPONENT TESTER. DELAY SWEEP. CE, TUV GS, UL, CUL, IEC1010.
-
Product
Analog Output Industry Pack Module, 12-bit D/A
IP220A
-
The IP220A outputs analog voltage signals to drive up to 16 devices. When used with a carrier that holds four IP modules, up to 64 voltage outputs can be obtained from a single card cage slot.
