Analog Input Output
Analog I/O are Devices that have the capability of sending and receiving analog signals.
-
Product
175W - Single Output / Multiple Output
NV CONFIGURABLE Series
-
*1-5 Outputs*Up to 90% Efficient*Active Power Factor Correction*Universal Input (90 - 264VAC)*No Minimum Loads*Medical Approvals
-
-
Product
200W to 250W - Single Output
CUS200M Series
-
*IEC 60601-1 (2xMOPP), IEC 60950-1 Approvals*200W Convection Cooled Rating*High Efficiency, up to 94%*Industry Standard 3" x 5" footprint*Suitable for B and BF rated equipment*5V Standby Output
-
Product
sbRIO-9375, Non-Enclosed, 24 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module
781212-01
Digital Module
Non-Enclosed, 24 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module - The sbRIO‑9375 is a digital I/O interface that works with industrial logic levels and signals for direct connection to a wide array of industrial switches, transducers, and other devices. Each digital input line is compatible with 24 V logic levels, and all the output lines are compatible with 6 V to 30 V signals, based on the external power supply. The sbRIO‑9375 offers isolation between the input and output banks from channel‑to‑earth ground. Non-enclosed modules are designed for OEM applications.
-
Product
864W to 1008W - Single Output
FPS Series
-
*1U High*Up to 3000W (3 units) in 19" rack*Hotswap capable (ORing diodes built in)*Low Cost*PoE Option
-
Product
Analog Output Module For Remote I/O
Analog Output Module
The Analog Output Module for Remote I/O features a 2-wire spring terminal connection, selectable output ranges (0 V to 10 V, ±10 V, 0 V to 5 V, ±5 V, 0 mA to 20 mA, 4 mA to 20 mA, and ±20 mA) output ranges, and short circuit proof outputs. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the Analog Output Module for Remote I/O from a real‐time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low‐cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high‐speed or specialty measurements.
-
Product
Analog Output Module, 16-bit D/A
IP230A
-
Jumper-selectable output ranges give you the choice of unipolar or bipolar voltage output. And for greater flexibility, the IP230A module accepts conversion start triggers from software commands, or from external sources for synchronization to specific events.
-
Product
Analog Optical Power Meter - PXI
Power 1500 Series
Power Meter
The Power 1500 Series analog power meter brings cost-effective test and measurement. The Power 1500 provides logarithmic analog output as well as a digital optical power meter for applications that require real-time feedback.
-
Product
Switched Amplifier With Analog Detector Output
-
Operates at 3 GHz-10 to -5 dBm Input Power to +4 to +7 Output powerAnalog Detector OutputTTL Compatible, 70 dB On-to-Off Ratio, 50 ηSec Response Integrated RF Switch
-
Product
sbRIO-9207, Non-Enclosed, 500 S/s, 16-Channel C Series Voltage and Current Input Module
781069-01
Current Input Module
Non-Enclosed, 500 S/s, 16-Channel C Series Voltage and Current Input Module - The sbRIO‑9207 is a combination voltage and current input module designed with industrial systems in mind. It features eight current and eight voltage input channels, with built-in noise rejection. Non-enclosed modules are designed for OEM applications.
-
Product
Analog Panel Meters (W)
-
Rishabh Instruments Pvt. Ltd.,
Measure AC/DC Voltage or Current and frequency. These meters are installed on 35mm Din rail, the mounting width is 45mm and it is housed in UL 94 V-0 approved polycarbonate case and can be mounted in Mosaic mounting (cascading).
-
Product
Analog to Digital Video Converter/Embedder
SDI Pro VADC-100
-
The SDI Pro VADC-100 converts composite analog video to SDI video and embeds two channels of analog audio.
-
Product
Dual Input Logging Thermometer
DT302
-
UEi Test & Measurement Instruments
This series of Digital Thermometers offers a unique combination of features including logging capabilities with 9,999 memory positions and a USB interface and software, one, two and four inputs offering relative and differential readings. The Apollo also offers a solution to storing probes and is manufactured to conform to the IP67 standard, meeting performance expectations of water submersion and high-pressure dust resistance.
-
Product
sbRIO-9237, Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
781028-01
Strain/Bridge Input Module
Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The sbRIO‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the sbRIO‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools. Non-enclosed modules are designed for OEM applications.
-
Product
8-Channel High-Speed Analog Input Module
ADAM-5017H
-
Accuracy: ±0.1% or betterEffective resolution: 12-bit plus sign bit1000 Hz bandwidthHigh sampling rate:ADAM-5000/485&5000E: 100 samples/sec, ADAM-5510 & ADAM-5511: 8000 samples/sec max3000VDC Isolation voltage protectionDistinct range settings allowed on each channelInput type: mV, V, mA
-
Product
PXI-6521, 16-Channel, ±30 VDC, 8 Sink/Source Inputs, 8 Relay Outputs, Isolated PXI Digital I/O Module
779313-01
Digital I/O
16-Channel, ±30 VDC, 8 Sink/Source Inputs, 8 Relay Outputs, Isolated PXI Digital I/O Module—The PXI‑6521 is an industrial digital I/O module with high channel isolation and industry-standard 24 V logic levels. For added safety, the PXI‑6521 requires a keyed connector. If a computer or application fault occurs, the PXI‑6521 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. It also features programmable power-up states, digital filtering, and change detection for optimal control over your application.
-
Product
Analog IC test system
-
A paradigm shift has been occurred in Japan’s major brand WL25 series tester. Ultimate simple system is available by effective analog pin architecture.This cost performance system is covered analog IC extensively, which are high accuracy, speed and multi-site test function.
-
Product
Digital and Analog Communications
-
1. Design and implementation of RF oscillators and filters. 2. Design and implementation of analog AM and FM modulation and demodulation. 3. Design and implementation of digital and analog converter. 4. Design and implementation of ASK and FSK modulation and demodulation. 5. Design and implementation of PSK and QPSK modulation and demodulation.
-
Product
15W to 960W - Single Output
DPP Series
-
*Low Cost*UL 508 Listed*Convection Cooled*Conducted and Radiated EMI, Class B*Input Transient Protection, IEC61000-4*Conforms to EN61000-3-2 (PFC)*Three year warranty
-
Product
NI-9203, 200 kS/s, ±20 mA, 8-Channel C Series Current Input Module
783731-01
Current Input Module
200 kS/s, ±20 mA, 8-Channel C Series Current Input Module - The NI‑9203 is intended for high-performance control and monitoring applications. It features programmable input ranges and variable connectivity options. To protect against signal transients, the NI‑9203 … includes a channel‑to‑earth ground double‑isolation barrier (250 Vrms isolation) for safety and noise immunity.
-
Product
Analog Measurement Unit
AMU05
-
The AMU05 (Analog Measurement Unit 05) is the core of all our test systems. It ensures that all the measurements are performed faster, more accurately and with even greater stability.
-
Product
Integrating Display Output A/D Converters
-
Renesas offers a selection of high-performance integrated display output analog-to-digital (A/D) converters.
-
Product
I-8000 Analog Data Acquisition Modules
-
ICP DAS offers a versatile array of analog, cartridge based I/O modules to meet the precise needs of sensitive data acquisition applications using I/W-8000 controllers. ICP offers a bevy of thermistor, thermocouple, RTD, strain gauge, and universal I/O, as well as high resolution analog output modules! Please note that more modules are available in the "serial 87k section".
-
Product
Analog Sequencers
-
Analog sequencers from Analog Devices integrate accurate comparators with the control functionality of power-on and power-down sequencing for voltage regulator banks. The comparators monitor the regulator voltage outputs and trigger the turn on of next rail in the system after a preconfigured time delay. Some members of this portfolio can be cascaded together, which provides scalable solutions to expand functionality across multiple devices. Our analog sequencers provide an easy to use solution for power sequencing challenges in cellular infrastructure, telecommunication, data communication, and data center applications.
-
Product
PXI Temperature Input Module
Module
PXI Temperature Input Modules offer up to 32 channels of analog temperature measurements. Some models include autozero channels for offset compensation as well as open thermocouple detection to identify disconnected thermocouples, while others support 2-, 3-, or 4-wire resistance temperature detector (RTD) measurements. PXI Temperature Input Modules support both high-speed and high-resolution modes. You can program channel configurations and scale measured data into engineering units.
-
Product
OEM DVB-S2 Receiver With ASI Output
DTM-3237
-
Compact module for receiving a full DVB-S2 or DVB-S transport stream and outputting it as ASI. With it's fast receiver architecture and advanced signal quality indicators, it is highly suitable for system integration.
-
Product
C Series Relay Output Module
Input/Output Module
The C Series Relay Output Module enables you to switch up to eight signals at 60 V maximum DC switching voltage and up to 250 V of maximum AC switching current. For quick reference, every channel features an LED to indicate the state of that channel. The C Series Relay Output Module allows for direct connection to a wide array of industrial devices such as motors, actuators, and DC devices.The C Series Relay Output Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
32 Channel Relay Output Switch
DP-VME-4224
-
DP-VME-4224 is a 32 Channel Relay Output Switch. Applications for this module includes hardware simulation, digital simulation, high-reliability systems, and automatic test equipment, and relay output for soft PLCs.
-
Product
300W to 500W - Single Output
CUS500M1 Series
-
*300W (500W Peak) Convection Cooled*500W with Forced Air*Medical Certifications (2xMOPP)*Class B Conducted and Radiated EMI*Suitable for Class I and Class II installations*Compact 3 x 5 x 1.46" size
-
Product
17W to 50W - Multiple Output
LWT-H Series
-
*Triple Output*26mm height*Outputs 2 and 3 isolated from output 1*Universal input (85 - 265VAC)*Low profile*Wattbox design
