Analog Input Output
Analog I/O are Devices that have the capability of sending and receiving analog signals.
-
Product
USB Modular Oscilloscope, 100 MHz, 2 Analog Channels
U2701A
-
100 MHz2 analog channelsMore accurate analysis of electronic designs with deep 32 Mpts memory and high 1 GSa/s sample rateSimple USB setup with plug and play capabilityGet the debug power you need with advanced triggering, automatic measurements, math functions including FFTs and moreQuick and easy measurement configuration and acquisition with bundled Keysight Measurement Manager (KMM) softwareDocument results more easily using the high speed USB 2.0 interface
-
Product
High Output Simulators
-
The Abet Gen II optical design, patent pending, dramatically increases the percentage of photons reaching the work plane.All electronics are packaged in the lamp house – no clutter of high power cables to deal with. A digital shutter timer allowing both manual and external control is included with every unit.Standard maintenance, lamp or filter replacement, does not require any tools.Locking indicator dials on all the system controls provide for a reproducible and stable setup.
-
Product
PXI 8 Slot BRIC 276x8 1-Pole Dual Analog Bus (6 sub-cards)
40-560A-121-276X8-M
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI/PXIe 16-Channel Digital Output Module
42-412A-024
-
The 40-412A-024 (PXI) and 42-412A-024 (PXIe) are 16-Channel Digital Output modules with high output voltage and current capability. The outputs can be used for high or low drive and each channel is capable of sourcing 0.5A from the high side or 0.5A sink on the low side. Accidental operation of both high and low side driver on the same channel is prevented by the supplied driver. Outputs are fully protected against over-voltage, over-current and thermal overload, ensuring robust and reliable operation in the toughest test environments. For high side driving, the voltage source is supplied externally, allowing the module to drive high capacity loads separate from the chassis power supply. For low side driving, the external source is not used and the module’s output operates an open collector or open drain driver.
-
Product
Input Modules
-
A Range of Input Modules To Support Most ApplicationsMix and match input modules for even greater flexibility. Up to 4 modules can be installed in the Synergy portable or Qb, 8 modules in the Synergy 8 and 16 modules in the Synergy Rack system.
-
Product
15W to 30W - Single Output
CC-P-E Series
-
*Compact Footprint / Low Profile*18-36 Vdc, 36-76 Vdc Inputs*3.3, 5, 12, 15 Vdc Outputs*Isolation: 1 kVdc (Case); 1.5 kVdc (Uncased)*-40 to 85 °C Operating Temperature*Parallel Operation
-
Product
High Performance Analog & Mixed Signal Test Solutions
Applicos
-
Effective mixed-signal test solutions demand know-how and experience. Low level analog signals need to be stimulated and analyzed near fast switching digital logic. Cross talk, magnetic fields, clock jitter, ground noise and non-linearity of components, are just a few of the problems that must be addressed. Applicos knows what it takes to design and produce high quality mixed-signal test solutions. They have been servicing the mixed-signal test industry since 1993 and have established a distinguished reputation for providing our customers with high performance, cost effective solutions. In 2018 we acquired Applicos B.V. to extend our portfolio for the ATE business.
-
Product
16 Relay Output Board, 8 Isolated Digital Input Channels, 24V
APCI-2200-16-8
-
16 electromechanical relays with change-over contacts ? Max. switching voltage for the relays: 60 V/DC, 48 V/AC ? Max. switching current: 1 A ? Short response time ? Option: 8 input channels for AC voltage, optically isolated, input voltage range: 12 - 24 V DC ? Watchdog: software-programmable release, stop and time selection.
-
Product
Analog I/O via Ethernet
2608 Series
-
16 inputs of voltage, thermocouple, or 4-20 mA16-bit A/D, 15 -bit D/AUp to 8 analog outputs with remote sensingAuto standardizationSelectable input gainAll differential inputsWatchdog TimerCompatible with Linux and WindowsUse our design assistant to configure a system and calculate pricing
-
Product
Mixed Signal Oscilloscope: 13 GHz, 4 Analog Plus 16 Digital Channels
MSOV134A
-
13 GHz analog bandwidth (upgradable)4 analog plus 16 digital channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (1.09 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Access the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
Product
Telephone Line Testers for POTS / Analog Line
-
*This analog line tester is suitable for all instalers installing telephone equepement on POTS line.*Led indications signaling the status of analog line.
-
Product
Mixed Signal Oscilloscope: 200 MHz, 2 Analog Plus 8 Digital Channels
MSOX2022A
-
200 MHz2 analog plus 8 digital channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 1 Mpts memory See more signal detail with 50,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add 20 MHz function generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time Easily set up teaching labs with our free Educator's Resource Kit
-
Product
Oscilloscope, 100 MHz, 2 Input Channels, 1 GS/s interleaved, 7 Mpts/Ch)
T3DSO1102
-
100 MHz, 500 MS/s per Ch, 1 GS/s interleaved, 2 CH, 14 Mpts/Ch DSO with 7"" Color Display.
-
Product
Camera Link PXI Output Module
-
It is a PXI module to output as a camera link signal NTSC video signal.For outputting a trigger signal when you have the image conversion, you can ignore the delay at the time of conversion.
-
Product
Loop Powered Trip Amplifier With Dual Relay Output
SEM1636
-
The SEM1636 monitors a (4 to 20) mA loop and provides two independent change over trip contacts set to trip at any point within the (4 to 20) mA range.
-
Product
Infiniium V-Series Oscilloscope: 16 GHz, 4 Analog Channels
DSAV164A
-
16 GHz analog bandwidth (upgradable)4 analog channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (1.32 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Improve your testing with the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
Product
32-CH Sourcing Type Digital Input EtherCAT Module
EPS-1032
-
ADLINK" s EPS slave system features modular design for flexible high channel density, rugged construction, easy maintenance, and intelligent performance, compatible with 3rd party EtherCAT products. Precise time-deterministic control enables I/O synchronization for critical applications, and FPGA and ARM technology allow users to fully monitor status of EPS modules and systems, including operating temperature and usage cycle of relay switching, as well as motion control status for general purpose motor drive control. In addition, the ADLINK EtherCAT configurator enables auto-scan and configuration across EtherCAT systems. The EPS" unique structural and electronic design supports hot-swappable function, reducing repair time, and the rugged construction and operating temperature range of -20°C to 60°C allow operation in the harshest environments.
-
Product
Analog Video Switch
RVG-SA1
-
Curtiss-Wright Defense Solutions
The RVG-SA1 is a rugged, size, weight, power and cost (SWaP-C) optimized analog video switch designed for use in the harsh environmental conditions that are encountered in aerospace and defense applications. Part of the Rugged Video Gateway (RVG) family, the RVG-SA1 can be incorporated into space-constrained manned and unmanned vehicles of all types.
-
Product
100W - Single Output
i3A Series
-
*1/32nd Brick Footprint*9-53 Vdc Input*3.3-16.5, 5-30 Vdc Adjustable Outputs*Up to 8 A max Output Current*Non-Isolated*Remote ON/OFF, Sense, Power Good, Trim
-
Product
Programmable Linear DC Power Supply, 3 Output, 0-32V/0-3.2A, 2.5V/3.3V/5V/3.2A
T3PS3000
-
Teledyne Test Tools new T3PS3000 is a Linear Programmable DC Power Supply with a 4.3 inch TFT LCD display. It has three isolated outputs: two adjustable channels and one selectable channel from 2.5 V, 3.3 V, and 5 V with output short and overload protection for each channel. Support for series and parallel operation of the two main channels extends its flexibility beyond the standard specification. The T3PS3000 features include programmability via USB or LAN, a graphical display of power waveforms, and the high resolution numeric display of voltage and current. Typical users are Education, Production, and Design and Development.
-
Product
32 Channel PWM Generator Module with Analog Outputs
DP-VME-5835
-
DP- VME-5835 is a Pulse Width Modulator module with analog outputs. This module has thirty two Pulse Width Modulated output channels and four analog output channels.
-
Product
MOTORIZED TRANSFORMER/RECTIFIER ASSEMBLY, 0-250 VDC, 200 A OUTPUT
18534PS1
-
Input power is 380 VAC, 3 PH, 50 Hz, P/N 18534PS1Output is 0 to 250 VDC, 200 Amp max.Variable Transformer is used to vary the output. SCR controller is not used, as it generates harmonics.Input control is 0 to 3.6 VDCIndoor enclosure, 50"H x 46"W x 36"DOutput voltage and current feedback as 4/20 mA for PLC interface.All input/output connections are inside the enclosure
-
Product
PCI 16 Reed Relay Output Digital Interface
8003
-
The 8003 PCI digital I/O interface provides 16 Reed relay outputs provide high quality, long-life, low current (10 Watt maximum), dry contact switch closures. Reed relays are well suited for low-current applications. The relays are normally open, and close when energized. Writing a 1 to the proper port bit can individually energize each relay.
-
Product
Analog Control Variable Gain Amplifiers (VGAs)
-
Analog Devices voltage controlled variable gain amplifiers provide continuous gain control over a wide dynamic range for a variety of audio and optical frequency bands. Our VGAs improve the dynamic range of a circuit by allowing users to adjust a signal’s amplitude in real time, which is invaluable for ultrasound, speech analysis, radar, wireless communications, and instrumentation-related applications.
-
Product
Analog or Digital Communications Switching Systems with D Type Connectors
RS Series
-
The RS Series computer controlled switching systems are designed to switch multi-wire groups of signal up to 25 wires. These systems are typically used for signals such as parallel TTL, RS232, RS422, WAN or modems, but can also be used for any group of analog or digital signals having a bandpass up to 30 MHz or a data rate up to 20 Mbps.
-
Product
Analog Ionizing Radiation Detectors
-
A great general purpose analog radiation detector. Detects from 0-50 mR/hr.
-
Product
Analog Limiter
SIM964
-
Stanford Research Systems, Inc.
The SIM964 Analog Limiter provides upper and lower voltage limits for conditioning dynamic signals. Limits are set between ±10 V with 10 mV resolution. Two rear-panel TTL signals are activated when upper or lower limits are exceeded.
-
Product
50W to 300W - Single Output
ZWS-BAF Series
-
*Universal input (85 - 265VAC)*10 Year e-cap Lifetime*Power Factor Corrected*Convection Cooled*Compact Design*Five year warranty
-
Product
PXI/PXIe High Density Digital Input Module, 128-Channel, 50V
40-414-101
-
The 40-414-101 (PXI) and 42-414-101 (PXIe) are 128-channel digital input modules with 50 V inputs and provide a convenient way of determining the status of input lines by comparing the input voltage with two threshold voltages - quickly establishing if the input is low, high or in an intermediate logic state.
-
Product
4 Channels of Strain Gauge Inputs for the SCS-800 Signal Conditioning System
SCS-817
-
The SCS-816 and SCS-817 amplifier/filter module provides eight 8-pole low-pass filters that can be individually configured for a cutoff-frequency from 0.5Hz to 70kHz(SCS-816) and 0.5Hz to 60kHz(SCS-817). Each of the SCS-816/SCS-817's eight channels features an instrumentation amplifier with software-selectable gains of 1 to 1000 in 1-2-5 steps.
