Analog Input Output
Analog I/O are Devices that have the capability of sending and receiving analog signals.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit High Speed Digitizer - 180 MS/s on 2 Channels, 2 Single-Ended Inputs
DN2.447-02
-
The digitizerNETBOX DN2.44x series allows recording of one, two, four or eight synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit High Speed DIgitizer - 250 MS/s on 12 Channels, 12 Single-Ended Inputs
DN6.442-12
-
The digitizerNETBOX DN6.44x series allows recording of up to 24 synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Product
2 inputs Centesimal Thermometer Pt100
HD2127.1
-
Centesimal thermometer in the range ±199.99 °C, decimal outside this range, 2 inputs for Pt100 probes with SICRAM module. Measuring range -200 °C…+650 °C.
-
Product
With SAT-IF input EDFA
HA4600/IF
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HA4600/IF series, is narrow-band multiplexing EDFA suitable for L-Band fiber link application. With build-in 1550nm Internal Modulation SAT-IF optical transmitter, used for inter-cutting DBS. The WDM inside will multiply the signal from TX and main line signal that is inputted from outside, then the combined signal will enter EDFA to be amplified to serve the local subscribers. To avoid the interferes caused by mismatching of the optical output power between TX and main line signal from outside, output power of the TX can go through a VOA, thus, it can be adjusted or set from the front panel. This unit is simple and clear, easy to be installed and tested. It offers a high quality and cost-effective solution for inter-cutting DBS into full optic relay 1550nm fiber CATV system and second-stage service area.
-
Product
Buffered Analog Crosspoint Switches
-
Analog Devices buffered video crosspoint switches offer multiple configurations from 8x8 up to 32x32 channels with gain of 1 or 2 and are offered in LQFP, LFCSP, and BGA packages. These crosspoint switches can be programmed either in serial or parallel modes and are used primarily for routing high speed signals, including composite video (NTSC, PAL, SECAM) and component video (YUV, RGB) in applications such as studios, video on demand, in-flight entertainment, surveillance, and video teleconferencing.
-
Product
8/4-Ch, 14-Bit, 20MS/s/ch Simultaneous Analog Input PCI Express DAQ Card
PCIE-1843
-
8 or 4 x Simultaneously Analog Inputs, up to 20 MS/s14-bit resolutionSupports digital and analog triggersWide input range up to 20 Vpp (±10 V range)Onboard FIFO memory (65,536 samples)
-
Product
Infiniium UXR-Series Oscilloscope: 25 GHz, 4 Channels, 1mm Inputs
UXR0254AP
-
The UXR0254AP is the 25 GHz, 4 channel, 1mm input, Infiniium UXR-Series real-time oscilloscope.
-
Product
4A Solid State Flasher, AC Input
A915-8
-
NAI’s A915-8 is a 4 A, AC Input, Aircraft Warning or Navigation Light Flasher. With low RFI/EMI, zero crossover switching employed in the output circuits, this solid state, single channel unit provides long device and load life.
-
Product
LXI Reed Relay Matrix - Single 128x4 Plugin, Direct Y Access, 6 Analog Buses
65-221-012
-
The range includes four plug-in models covering matrices of up to 1,536x4 in increments of 128 (model 65-221), 768x8 in increments of 64 (model 65-223), 384x16 in increments of 32 (model 65-225), and 192x32 in increments of 32 (model 65-227). Users can specify as many or as few plug-in modules (up to six) required and can field upgrade the chassis to extend the matrix when necessary. Another important feature is that over 1,500 relays can be closed simultaneously for specific conditions for parametric testing.
-
Product
725-Watt (28VDC input) DC/DC Converter, SOSA™ Aligned, 3U VPX
VPX55HS
-
NAI’s VPX55HS-31 is NAI's latest +28 VDC Input, VPX DC/DC Converter. The VPX55HS was developed in alignment of the SOSA™ Technical Standard and is capable of handling up to 725 Watts of output power. It plugs directly into a standard 3U VPX chassis with a VITA 62 1.0” power supply slot. This off-the-shelf solution for VITA 46.0 and VITA 65 systems is compatible with VPX specifications; supports all VITA standard I/O, signals, and features; and conforms to the VITA 62 mechanical and electrical requirements for modular power supplies.
-
Product
MOTORIZED TRANSFORMER/RECTIFIER ASSEMBLY, 0-250 VDC, 200 A OUTPUT
18534PS1
-
Input power is 380 VAC, 3 PH, 50 Hz, P/N 18534PS1Output is 0 to 250 VDC, 200 Amp max.Variable Transformer is used to vary the output. SCR controller is not used, as it generates harmonics.Input control is 0 to 3.6 VDCIndoor enclosure, 50"H x 46"W x 36"DOutput voltage and current feedback as 4/20 mA for PLC interface.All input/output connections are inside the enclosure
-
Product
PXI 4 Slot BRIC 138x8 1-Pole Dual Analog Bus (3 sub-cards)
40-560A-021-138X8-M
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
Inputs Temperature Data Logger – Pt100
HD32.7
-
The instrument HD32.7 is a robust 8 inputs data logger for Pt100 sensor temperature probes. The probes can be Pt100 with SICRAM module, direct 4-wire Pt100 or direct 2-wire Pt1000.
-
Product
Analog Oscilloscope
PS-600
-
*60MHz DUAL TRACE, DUAL TRIGGER.*VERT SENSITIVITY FROM 1mV/DIV TO 15V/DIV.
-
Product
Infiniium S-Series High-Definition Oscilloscope: 4 GHz, 4 Analog Channels
DSOS404A
-
4 GHz bandwidth (upgradable)4 analog channels Capture a longer signal trace with 20 GSa/s max sample rate and 100 Mpts/channel of standard memory Get superior signal integrity with system ENOB of 7.2 bits and 10-bit analog-to-digital converter (ADC)Gain increased usability with the multi-touch supported 15 inch capacitive touch screen and solid state drive for fast boot and reliability Improve your testing with a wide range of protocol, compliance, and analysis software
-
Product
12-bit, 100KHz, 16SE/8DIFF Isolated Analog Input Board
APCI-3001-16
-
16 single-ended or 8 differential inputs 12-bit resolution Optical isolation 500 V 100 kHz data transfer rate Automatic analog acquisition 8 digital I/O, 24 V, isolated, timer Trigger functions Graphical display of the measured data
-
Product
High Definition Oscilloscope, 350 MHz Bandwidth, 4+16 Input Channels, 10 GS/s
HDO4034A-MS
-
350 MHz,4+16Ch,12-bit,10 GS/s,12.5 Mpts/Ch HD Mixed-Signal Oscilloscope w/ 12.1" WXGA Color Display.
-
Product
48-Channel VME Isolated Digital Input Module
V280
-
The V280 is a single-wide, 6U VME module that includes 48 isolated logic inputs. It is available in versions for nominal 5 volt or 24 volt input levels. The V280 has independently programmable rising and falling edge response times to support contact debounce, glitch catching, and DC or AC inputs.
-
Product
4 (High Voltage) D/A Outputs (+20 VDC to +80 VDC)
DA4
-
The DA4 module features 4 high-voltage D/A output channels with a maximum full-scale range of ±80 VDC at ±10 mA (max).
-
Product
Uni-directional Two Outputs Optical Receiver
9112, 9182 (Out-door)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Guangtai 9112 two outputs optical receiver has the same performance and index as 9912, except without bi-directional function. Guangtai 9182 low input two outputs optical receiver has the same performance and index as 9982, except without bi-directional function.
-
Product
Ethernet/LXI digitzerNETBOX 14 Bit High Speed Digitizer - 500 MS/s on 2 Channels, 2 Single-Ended Inputs
DN2.445-02
-
The digitizerNETBOX DN2.44x series allows recording of one, two, four or eight synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Product
NI-9230, 3-Channel, 12.8 kS/s/channel, ±30 V, C Series Sound and Vibration Input Module
783824-01
-
3-Channel, 12.8 kS/s/channel, ±30 V, C Series Sound and Vibration Input Module - The NI‑9230 can measure signals from integrated electronic piezoelectric (IEPE) and non‑IEPE sensors such as accelerometers, tachometers, and proximity probes. The NI‑9230 is also compatible with smart TEDS sensors. The NI‑9230 incorporates software-selectable AC/DC coupling, IEPE open/short detection, and IEPE signal conditioning. The input channels simultaneously measure signals. Each channel also has built-in anti-aliasing filters that automatically adjust to your sample rate. When used with NI software, this module provides processing functionality for condition monitoring such as frequency analysis and order tracking.
-
Product
Low pin and internal configurable analog MCU
RL78/G11
-
The RL78/G11 microcontroller line-up concept is based on small packages like 20 to 25pin, in small 16KB flash memory and rich analog peripherals such as A/D converters, D/A converters, comparators and PGA and these are configurable as PGA+ADC+VBGR, PGA+CMP, CMP+DAC/VBGR, or PGA+CMP+DAC/VBGR. Using the smart features like DTC and ELC a lot of peripherals can be connected internally to reduce CPU workload and can save overall power consumption. It also supports very low power operation (100 uA @ 1 MHz ) and a high speed 4µs wake up. Available in small 3x3mm² WFLGA , 4x4mm² HWQFN and standard 20pin LSSOP, this MCU line is suitable for sensor application, Lighting/power sources and many small appliances.
-
Product
NI-9478, 50 V, 16-Channel (Sinking Output), 50 µs C Series Digital Module
779940-01
-
50 V, 16-Channel (Sinking Output), 50 µs C Series Digital Module - The NI‑9478 works with industrial logic levels and signals to connect directly to a wide array of industrial relays, solenoids, and motors. The NI‑9478 features programmable current limits, which provide customizable system protection that is ideal for solenoid and valve control applications. Each channel is compatible with signals from 5 V to 50 V and features isolation from channel‑to‑earth ground.
-
Product
W-band Transmitter (94 GHz, 50 MW Output Power)
-
W-band Transmitter (94 GHz, 50 MW Output Power)
-
Product
Oscilloscope, 200 MHz, 4 Input Channels, 2 GS/s interleaved, 200 Mpts - interleaved
T3DSO2204A
-
200 MHz, 2 GS/s per Ch, 2 GS/s interleaved, 4 CH, 200 Mpts/Ch DSO with 10.1" Color Display.
-
Product
12-bit, 100KHz, 8SE/4DIFF Isolated Analog Input Board, LACQUERED
APCI-3001-8-LAC
-
LACQUERED 8 single-ended or 4 differential inputs 12-bit resolution Optical isolation 500 V 100 kHz data transfer rate Automatic analog acquisition 8 digital I/O, 24 V, isolated, timer Trigger functions Graphical display of the measured data
-
Product
Mixed Signal Oscilloscope 200 MHz, 4 Analog Plus 16 Digital Channels
MSOX3024G
-
The MSOX3024G 200 MHz oscilloscope provides 4 analog plus 16 digital channels, 4 Mpts memory, 1,000,000 waveforms/sec update rate, zone touch trigger with an 8.5-in capacitive touch screen, and standard embedded software with waveform and measurement histograms.
-
Product
Infiniium V-Series Oscilloscope: 13 GHz, 4 Analog Channels
DSOV134A
-
13 GHz analog bandwidth (upgradable)4 analog channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with low noise floor (1.09 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Improve your testing with the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
Product
16-Ch, 24-Bit Thermocouple Input IDAQ Module
iDAQ-868
-
Hot-swappable in iDAQ system16-channel thermocouple sampling24-bit resolution50/60Hz rejection filter availableWide range of thermocouples supportedIsolation protection up to 600VRMS
