PC
Checking personal computers and using a pc as host to perform test.
-
product
Networked CCTV
TCP/IP
As most of the test sites are using a LAN, we also offer camera systems that are accessed and controlled via TCP/IPIn this case the camera or controller has an Ethernet interface that is connected to the LAN. If our video control SW is installed on a PC, You may access the camera via this SW from any location within the net work.The Audivo video control software, allows you to view up to 4 cameras on one screen. The access can be limited to special defined users.The IP access gives the tools to store screen shots for documentation on the local HDD of the PC.
-
product
5 / 10 / 20 MHz Multiwaveform Arbitrary Signal Generator
MASG Series
- Economic and Light Weight- Dual Output with Same Characteristic- 1µHz Frequency Resolution- 11 Built-in Waveforms and 5 User defined Arbitrary Waveforms- AM, FM, PM, PWM, FSK Modulation, Frequency Sweep and Burst Function- Built-in 100MHz Frequency Counter- Arbitrary Waveform Editing PC Software- USB Host, USB Device
-
product
Torque Measuring and Monitoring System
WISER 4000
TECAT Performance Systems, LLC
The WISER 4000 system is the latest release of TECAT’s low-cost, ultra-low power and extremely accurate torque sensor. The wireless system has the optional ability to measure 3-axis acceleration, barometric pressure and ambient temperature, all within the same incredibly small footprint. The 4000 includes on-board data logging without PC or DAQ connectivity, and remote flash capability, which enables firmware upgrades without removing the system from the unit under test. Featuring shunt calibration, TECAT’s latest WISER system is designed to simplify instrumentation verification for users, while allowing them to check calibration of the system in the field. In addition, the WISER 4000 has been enhanced with two additional outputs, a higher-speed recording, and is available with custom-built remote enclosures to protect the system’s remote unit and battery from damage due to debris.
-
product
GPIB-RS485/RS422 GPIB Instrument Control Device - Brazil 127-220VAC
779733-12
The GPIB‑RS485 is an IEEE 488 controller device for PCs with RS485 or RS422 ports. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS485 or RS422 serial port into a talker, listener, or controller on the GPIB bus. It can also interface RS485 and RS422 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488, RS485, and RS422 standards, as well as interpret and execute high-level commands from the serial port, including serial‑to‑GPIB, and GPIB‑to‑serial protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
Magnetic Shielding Cabinet for EMI Testing
SDR-2000B
Cabinet Shell 2mm galvanized cold-rolled steel sheetCabinet Door 0.9*1.7m(L*W) 0.6*0.6mCabinet Window 0.3*0.3*0.025m(L*W*T) with 4mm hole N/APower Supply Filter 30A/220V 30A/220VInternet Line Filter RJ-45 N/ACabinet Inside Decoration PVC ceiling, PVC plastic steel wall, 10mm wooden + 2mm galvanized steel sheet floorCabinet Inside Size 2*1.2*1.8m 0.8*0.8*0.8mAfter Packing Size 2.2*2.3*2.3m 1*1.1*1.2mAfter Packing Weight 800kg 200kgWorking With EMI-9KA/EMI-9KB EMI-9KA/EMI-9KB, PC, Testing load, and operator inside Testing load is inside to connect with EMI-9KA/EMI-9KB via BNC
-
product
Combinated Thermometers
PeakTech Prüf- und Messtechnik GmbH
Professional "5 in 1" environmental video measuring device with a dual laser for exact target area determination for fast, accurate and non-contact surface temperature measurements. An additional type K measurement input is available on the device for direct contact measurements or differential measurements of surfaces. The integrated photo function displays the measured object with the temperature displayed and other measurement data such as air humidity and dew point temperature and can be saved in the internal memory or on a microSD card. The integrated data logger saves all measured values which can be evaluated and processed on the PC. Ideal for documenting important measurements in the industrial sector, electrical engineering, maintenance and service work, quality assurance, construction and energy consulting.
-
product
Signal Generator, 30MHz, 1 Channel
33519B
With these signal generators, Keysight introduces the highly accurate True form technology. It generates true point-by-point arbitrary waveforms with ten times less jitter than current Direct Digital Synthesis (DDS) technology. The tracking filters allow for clean, alias-free signals. The devices have USB, LXI and GPIB interfaces for remote control from the PC.
-
product
Interface Adapter. USB Solution
U2C-11
Dimax USB to I2C Bridge device - U2C-11 converts USB transactions to I2C Master transactions. U2C-11 turns your PC running Windows or Linux OS into comprehensive I2C Bus master.
-
product
Basic 3U VPX-to-PCI Express (PCIe/PCI-e) Adapter
8462
The Technobox, Inc. P/N 8462 is a 3U VPX-to-PCI Express (PCIe) adapter that provides a convenient and cost-effective means for developing 3U VPX boards in a personal computer environment. It can also be used for production testing of 3U VPX boards. The adapter is a half-length PCIe card with the VPX card under test mounted close to the PCIe edge fingers to minimize signal lengths. When seated in a PC motherboard, the VPX card primary side faces upward to allow convenient access to components.
-
product
Auditor Universal Electronic Testers
AUET-DC Series
The Auditor Universal Electronic Testers (AUET) have a broad range of features to accommodate most requirements. These instruments are designed to be bench top mounted and are available in several configurations and various single or multiple torque ranges. They are also available with file capability (DC) models. The DC models require PC software Auditor Tool Manager (ATM).
-
product
100BASE-T1 MEDIACONVERTER BCM
Art.-Nr.: TE-1000
The ideal physical layer conversion between Automotive Ethernet and your PC system. The 100BASE-T1 MediaConverter BCM establishes one direct point-to-point conversion between automotive ECU’s using 100BASE-T1 and any standard Fast Ethernet device with RJ-45 connector.
-
product
Terminal Test Kit (94 Pcs)
3601
Peaceful Thriving Enterprise Co Ltd
*Total: 94 pcs*Alligator Clip x 2 pcs*Testing Probe x 2 pcs*Flat Terminal x 48 pcs*Testing Needle x 4 pcs*1 to 2 Connector x 2 pcs*Round Terminal x 24 pcs*5K Variable Resistor x 2 pcs*Polarity Tester / Stroboscope x 2 pcs*Insulator Pierce Through Clip x 2 pcs*SRS Air Bag Replacement Connector x 2 pcs*Male / Female to Male / Female Extension Wire x 4 pcs
-
product
GPIB-RS485/RS422 GPIB Instrument Control Device - Taiwan 110VAC
779733-11
The GPIB‑RS485 is an IEEE 488 controller device for PCs with RS485 or RS422 ports. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS485 or RS422 serial port into a talker, listener, or controller on the GPIB bus. It can also interface RS485 and RS422 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488, RS485, and RS422 standards, as well as interpret and execute high-level commands from the serial port, including serial‑to‑GPIB, and GPIB‑to‑serial protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
Temperature Data Loggers
It can also be used as an Easy and Protable Meter. This data logger measures and stores up to 32,000 temperature(-35 to 80℃(-31~176℉)) readings. Some professional applications can be provided by the PC software DGraphTM. Logger status, alarm indication and low battery indication are via flashing red/green LED and yellow LED. The button on housing can be used to start logging, or confirm and clear LED alarm when LED alarm is hold status.
-
product
Power Supply for Watthour Meter Test
DAC-3100
DAC-3100 is a power supply system that can generate precise and stable power under electronic-burden conditions for watthour meter tests.This system has the Touch-Panel Control unit, and you can control it via PC.
-
product
Avionics Data Loaders
The Ballard DL 615 Data Loader is the modern replacement for outmoded 3½-inch floppy-disk-only ARINC 615 portable data loaders (PDL). Any PC running Microsoft® Windows® can perform data loads using the USB to ARINC 429 interface, cables, and software included with the DL 615. While being as simple to use as older floppy disk PDLs, the DL 615 provides record keeping, flexibility in data management, and powerful features for troubleshooting and enabling data loads into difficult LRUs. As an added benefit, the interface can be used as a general purpose ARINC 429 (and optionally ARINC 717) maintenance tool.
-
product
PCIe Carrier For PMC And PrPMC
PCI104
The PCI104 is a PCIe carrier for PCI Mezzanine Cards (PMC) or Processor PCI Mezzanine Cards (PrPMC). The PCI104 carrier allows simplified testing of PMC/PrPMCs and their associated PMC I/O Modules (PIMs) by using a PC environment during board development or deployment. The PCI104 can also reduce the costs of manufacturing PMC/PrPMCs by allowing manufacturers to use off-the-shelf PCs for functional testing. The PCI104 converts the PCIe x4 edge connection to PCI-X via a PCIe to PCI-X bridge. The trace lengths to the PMC/PrPMCare kept to a minimum so the PMC/PrPMC can run with a133MHz PCI-X clock speed. The J4 connector of the installed PMC/PrPMC is routed to a 96-pin DIN connector per theVITA-35 specification. The PCIe to PCI-X bridge can run in either transparent or non-transparent mode and can also operate in forward or reverse mode. The PCI104 has a fan mounted on the board to cool the PMC/PrPMC. The fan can easily be removed for testing and probing of hosted card.
-
product
Hand Held Video Tester
The hand held video tester is our world class video hardware and VIDSoft suite integrated to a micro PC via ATTI’s slot-0 service. The intent of the slot-0 service is to eliminate the bottleneck of VISA and PCI bridging.
-
product
Signal Conditioners
Datexel has a large range of Signal Conditioners. We manufacture Thermocouple Transmitters, that are either Head Mounted, Din Rail and we even have an OEM version that can fit inside an enclosure smaller than 1" x 1/4". These Temperature Transmitters are PC programmable or DIP Switch programmable. Some are isolated and accept input from various sensors such as RTD's, Thermocouples Voltages, Current, Resistance and Potentiometers. They have current outputs and we even have Temperature converters that have voltage outputs.
-
product
Electronic Ballast Tester
WT4000
• Measure parameter: 1) Input: Vrms, Lrms, W, PF, Hz, Phasic angle, total harmonic and 0-39 component of harmonic. 2) Output: Lamp voltage, Lamp current, Filament current, Guided cathodic current, Lamp power, crest factor and oscillatory frequency, single high frequency analysis. • Startup: Startup lamp voltage, lamp current, filament current, guided cathodic current curve and parameter, preheating time; • Simultaneously display on 8 windows for input and output parameters, convenient for comparison and analysis; • Test preheat energy, filament preheat time. And the parameters changes from 0 to 5s of filament voltage, filament current and filament power; • Up to 1MHz lrms test content to every EB; • Analysis symmetry of high Frequency curve of lout; • 12-bit high-speed A/D, sampling rate up to 10MHz, can easily analyse signal curve of output; • Finish an input and output testing at the same time within 1 minute; • Portable, can test, display, print without computer. Test report include data and curve, comply with international standard; • Communication port for PC, run under Windows98 or Windows2000, English Version available.
-
product
Three-axis Fluxgate Magnetometer
TFM1186
The Three-axis Fluxgate Magnetometer TFM1186 is a member of Metrolab's THM1176 family of 3-axis handheld magnetometers. It is a lightweight, low-power, go-anywhere fluxgate magnetometer. Outstanding noise characteristics make fluxgate magnetometers the instrument of choice for measuring minute disturbances in the local magnetic field, for example due to an iron mass or AC power-line noise. The TFM1186 has a range of ±100 µT and a resolution of 4 nT. The TFM1186 simultaneously measures all three axes of the magnetic field, so you get a true field strength reading no matter how you hold the probe. The entire instrument has been reduced to a cable with a few fat spots, which can plug directly into your PC or into a battery-powered handheld computer. 3-axis Teslameter Gaussmeter
-
product
Rugged PC Compatible
SYS-405S
The SYS-405S is a rugged, industrial system capable of operating at extended temperatures without requiring a fan or heat-pipe. The SYS-405S is based on the quad-core Intel® Atom™ E3815 processor and protected by a rugged enclosure.The SYS-405S includes dual Ethernet, dual MiniPCIe, USB 3.0, serial ports with RS-232/422/485 and two independent displays via DisplayPort, and/or Analog VGA.
-
product
Safety Test Panel for Mixer
SCR ELEKTRONIKS introduces Safety Test Panel for Domestic Mixer with PC Datalogging. The tests are Performed as Prescribed in IS the Panel Carries out different tests one by one and provides indication of the Test results as OK or NOT-OK. It is very useful and handy in line testing on Mass production line as well as type Testing. Special fixture can be provided for the specific product. This avoids the connections & disconnections of the product for different tests. The total time for entire testing is less than 20 seconds. Micro controller based sequential timer maintains the sequence of operation and displays the test status. This manual contains information about operating instructions and maintenance of the equipment. Please go through this manual carefully and retain it for future reference.
-
product
Circuit Breaker Analyzers & Timers
CAT circuit breaker analyzers and timers are advanced standalone or a PC controlled instruments for circuit breaker maintenance. Typical application areas of CAT instruments are medium and high voltage substations at electric power generation, transmission, and factories of switchgear. Also, industrial environments and electric power distribution are suitable application areas for these circuit breaker testing instruments.DV Power CAT circuit breaker testing instruments are portable and lightweight. They are designed for performing mechanical operations intended for circuit breakers testing according to standards IEC 62271-100 and IEEE C37.09.These instruments measure:the timing of main contacts, pre-insertion resistor contacts, auxiliary contacts operations,coil currents,motion parameters,voltage recording,main circuit resistance,arcing contacts wipe,and any relevant analog signal.Motion transducer channels provide measuring a displacement of the circuit breaker moving parts, contact wipe, over-travel, rebound, damping time, and average velocity. Even more, CAT circuit breaker analyzer optionally has a built-in micro-ohmmeter. Hence, it provides the main circuit resistance measurement and dynamic resistance measurement. Dynamic resistance measurement is an effective method for arcing contacts condition assessment.
-
product
AC + DC TRUE RMS Digital Multimeter With PC Interface
KM 829
Kusam Electrical Industries Limited
• Beep-Jack Audible & Visible Input Warning• Auto-Ranging• Relative Zero Mode• PC Interface Capability• AutoCheck V-Ω ; Auto-Ranging• Crest (Instantaneous Peak Hold)• T1-T2 differential Temperature readings.• Data Hold
-
product
Compact USB Programmer
S6
The Dataman S6 is a USB powered universal 48-pin programmer with compact dimensions and minimal weight • USB powered - no additional power supply is required • Over 16,000 devices supported with new devices added monthly • Intelligent pin drivers operate down to 1.8V so you'll be ready to program the full range of advanced low-voltage devices • Hi-speed USB 2.0 connectivity • Easy to use software compatible with the latest operating systems including Windows 10 • Multiprogramming support allows one PC to control up to eight units programming as a gang programmer • Comprehensive 3 years parts and warranty • Free life-time software updates
-
product
Ultra-High Vacuum Scanning Kelvin Probe
Our Ultra-high Vacuum Scanning Kelvin Probes (UHVSKP2020 and UHVSKP5050) give the user full access to work function (Φ) and contact potential difference (CPD) measurements under vacuum with the ability to scan a sample area of 20 x 20mm or 50 x 50mm respectively. Each system comes with the UHV head unit, tip amplifier (located at the mounting port), digital control unit and host PC with dedicated software. The tip can be retracted 100mm from the sample and approaches normal to the sample. The associated digital electronic unit powers the head unit and provides an interface between the head unit and the data acquisition system. The system comes with a complete user manual, which includes an introduction to work function measurements and a detailed description of the system software, including examples. The work function resolution of the Ultra-High Vacuum Scanning Kelvin Probes is 1-3 meV.
-
product
LXI Function Card Carriers
ProDAQ 6100 Series
Ethernet-based LXI is changing the way engineers and scientists perform test and measurement and data acquisition. As more and more PCs ship without expansion slots, customers are faced with the problem of replacing their test and measurement and data acquisition equipment. Bustec believes in the power of distributed systems and the use of IEEE standards.
-
product
ARM 9 System on Module
MS 1515
- Processor: LPC3250 processor with ARM 9 core running at 266 MHz SDRAM- Memory: DDR2 256 MB (scalable to 512 MB)- Flash Memory: NAND flash 512 MB- Display & Graphics: Programmable color LCD controller supports up to a TFT interface- Touch screen: Integrated touch screen controller- Network Support: 10/100 Base-T Ethernet PHY- PC Interface: One USB 2.0 high-speed On-the-Go interface- Serial Interfaces: Up to four external UARTs- + CAN 2.0B controller- + Three I2C ports- + Three SPI ports- GPIO: Programmable I/O depending on peripheral requirements- Mechanical: 60 mm wide x 60 mm long x 5.4 mm high
-
product
MOTUS Stand-Alone Sensor
There are numerous ways of measuring Ocean Waves. At Aanderaa, we focus on three measurement types: pressure, acoustic, and motion. In this section, we cover the motion-based sensors in the MOTUS family.MOTUS Directional Wave Sensor is suitable for integration on different buoy types. It is intended for commercial as well as research use. The directional stand-alone Sensor processes wave data and is configurable to directly present parameters and wave spectrum. The sensor can be connected to a SmartGuard using the CANbus-based AiCaP protocol. It can also be connected to a PC or third-party systems through the RS-232 interface.MOTUS Wave Height Sensor is for wave height only. As the MOTUS Directional Sensor, it is suitable for integration on different buoy types. In the sensor, the directional wave parameters are locked. It is possible to open the wave direction parameters with a software license from Aanderaa later if the need changes. MOTUS Lite OEM Sensor is the OEM version of the MOTUS Directional Wave sensor. It is delivered as an electronic board without housing and cables. Please get in touch with the factory for more options and restrictions.
