DC/DC Converters
Takes DC input and then provides regulated and/or isolated DC output.
-
product
Three-Phase Converters
SIRIO 3PH 7 ALFA 3PHSAP
The three-phase converter is an electronic equipment able to vary the RMS value of a sinusoidal voltage by controlling no. 6 controlled, antiparallel-connected conducting diode pairs.Since the wave form is symmetrically split both into positive and negative halfwave, the output voltage average value is not affected and equal to zero. This means that three-phase loads can be fed without gene rating inside the mesh a circulating current with average value other than zero.Moreover, the three-phase converting is obtained with only one control circuit thus ensuring balance between the three linked voltages applied to the load.
-
product
BCD to Binary Converter
BCD250
Computer Conversions Corporation
The BCD Series of BCD to Binary Converters will convert 4 digits of scaled BCD angle data with a full scale of 359.9degrees into 12 Bits of binary angle data (MSB=180degrees). These units are entirely digital, require no timing or control signals and do this conversion in less than 500 nano-seconds. Logic levels are TTL/DTL compatable and +5V DC power is required. They are packaged in a 2.6 x 3.1 x .82" H PC board mounting module.
-
product
Interface Converter
ZET 7176
Interface converter Ethernet/Wi-Fi↔CAN ZET 7176 is used for connection of CAN interface instrument communications nets based on digital transducers to PC over Wi-Fi or Ethernet. Wi-Fi or Ethernet network throughput rate allows to immediately fulfill commands and transmit great scope of data. Shared use of ZET7176 and ZET 7172 interface converters allows arranging instrument communications nets with radio linked transmission interface.
-
product
O/E Converter
TIA-1200
The TIA-1200 optical to electrical converter is a convenient battery powered wideband detection system for fibre optic applications. With a typical bandwidth of DC to 12 GHz (min. 10 GHz), it accurately provides an electrical replica of the optical signal presented to it. It is intended to drive a 50 ohm cable terminated in its characteristic impedance.
-
-
product
Converter
ARINC 429
ARINC 429 runs at one of two speeds – 100KHz or 12.5 Khz (nominal). But, the Russians have created an 'ARINC 429 like' standard, which operates at ~ 50KHz. Our customer needed to convert the 50 Khz 'Russian ARINC' to standard high speed ARINC 429, so that their existing test rig would accept it. Our solution all fits in this very small enclosure.
-
product
RS-232/RS-485 Converter
ECD485
Deploy sub-metering sites and simple metering networks with ease using the EDMI MiniHub RS-232 to RS-485 converter.1/4 Load RS-485 modules allow for up to 128 devices over 1.2km of wired daisy-chain network, with each meter capable of becoming the Network Master and remotely connecting to a backhaul system via an integrated EDMI Modem Port redirect connector.
-
product
Transition Time Converters
Designed Specifically for High Speed Digital Networks utilizing modified Bessel Filter Function.
-
product
Integrated TFT-LCD DC-DC Regulators For Automotive
Renesas' portfolio includes automotive-grade multiple output regulators for use in TFT-LCD automotive applications.
-
product
IPv6 to IPv4 Converter
An IPv6 to IPv4 Gateway is known by many names, including IPv4 IPv6 converter, IPv6 to IPv4 gateway, IPv6 to IPv4 network gateway, IPv6 converter, IPv6 gateway, or IPv4 converter. Some people refer to these solutions as IPv6 Compatibility tool, IPv6 compatibility appliance, IPv6 compatibility device, IPv6 transition mechanism or IPv4 to IPv6 tool.
-
product
D/A Converters (DAC)
Analog Devices has the industry’s largest portfolio of D/A converters ranging from 8 bits to 24 bits. ADI DACs are unmatched in their ability to deliver performance and value by providing accurate and reliable conversion for a range of applications including industrial automation, programmable logic controllers, optical transceivers, data acquisition, and more. Our portfolio includes integrated output amplifier options for ease of use, dynamic range DACs for multicarrier generation over a very wide bandwidth, and a variety of other digital to analog converters to suit your design needs.
-
product
Balanced O/E Converter
TIA-527
The TIA-527 balanced optical to electrical converter provides adjustable gain and a bandwidth of DC to 125 MHz. It is useful for coherent heterodyne detection applications, spectroscopy and similar applications for which the ability to discern small variations in signal strength in two optical paths is critical..
-
product
Industrial Media Converters
Advantech's industrial media converters can convert Ethernet data and power into fiber optic signals. They also offer Link Fault Pass-Through (LFPT).
-
product
Signal Isolators and Converters
DC powered isolator/signal converter to convert 0-20 mA or 4-20 mA into 0-10 V DC or vice versa in any combination. Easy to switch the inputs & outputs, by just changing the DIP switches.
-
product
USB Converters and Hubs
The C1/D2 USB converters and hubs offer industrial features like high retention USB ports, DIN rail mounting, isolation, and wide temperature ranges.
-
product
Resolver-to-Digital Converter
MSX-RDC-17
The resolver-to-digital converter MSX-RDC-17 is a device for supplying and acquiring a resolver. It converts the position value given by the resolver into a digital incremental output signal. The resolution of the incremental encoder output can be defined using the switch on the front side of the MSX-RDC-17.
-
product
PCI Converter
ES-200
The eSATA PCI BRACKET takes the blazing speed of eSATA outside your computer case with this external plate adapter. Simply install the PCI plate in an open PCI slot on your computer and attach the SATA cable to an available motherboard connector. Now you have an external eSATA port.
-
product
Frequency Converters
CAES offers a full range of custom frequency converter solutions including narrowband, wideband and block upconverters and downconverters.
-
product
Pattern Converter for WGL/STIL to ATE
VectorPort
VectorPort is a versatile, low-cost test development tool for converting WGL or STIL vectors to targeted ATE tester formats, including pattern, timing, and pinmap data. VectorPort can read and write all major formats in both parallel (Flat) vectors and serial (SCAN) vectors.
-
product
DC-DC Power Supplies
Advanced Conversion Technology, Inc
Units are available for use in extreme temperatures and other harsh conditions. We also offer products that meet specific military standards including MIL-STD-704A requirements for handling high voltage spikes and MIL-STD-1275 specifications for low input voltage transients. DC-DC power supplies can be VME rack mounted, bench mounted or installed in a ruggedized frame. High and low voltage units are available, as are hermetically sealed ion pumps and shipboard power supplies.
-
product
MACC Protocol Converters
Introducing the ultimate solution for effortless communication between different protocols - our state-of-the-art MACC II protocol converter.This powerful device allows you to easily translate messages between MIL-STD-1553, ARINC-429, Ethernet, Serial and more, ensuring compatibility and reliability in your aerospace and defense systems.With its advanced features and user-friendly interface, our protocol converter is the perfect solution for aircraft manufacturers, avionics designers, and military system integrators. It offers accurate and efficient data transfer, making it ideal for use in a wide range of applications such as aircrafts, ground vehicles, and naval vessels.Our protocol converters, both rugged, to withstand harsh environments, and standard, for the lab, are fully customizable to meet your specific needs. Its compact and lightweight design makes it easy to install and integrate with other systems.Don't let communication protocol limitations hold you back - Upgrade your systems today and experience the difference!
-
product
I/P Electro-Pneumatic Signal Converters
TEIP11 / TEIP11-PS
Electro-pneumatic signal converters are the link between the control rooms and pneumatic actuators. I/P converters are available with and without booster stage.
-
product
Plane Mirror Converter
10722A
The Keysight 10722A plane mirror converter modifies the use of the 10702A linear interferometer. With an additional 10703A reflector, the 10722A converts the 10702A into a 10706A plane mirror interferometer. With an additional 10723A high-stability adapter, the 10722A converts the 10702A into an 10706B high-stability plane mirror interferometer.
-
product
ARINC 818 to DVI Converter
The ARINC 818 to DVI converter is a rugged standalone module available in 6U cPCI form factor used for ARINC 818 to DVI conversion, DVI to ARINC818 conversion, ARINC 818 Mux as well as ARINC 818 Duplicator either on front panel or via cPCI back panel. It is a video Converter module designed with Cyclone V GT FPGA, using Analog device Video Encoder, and Decoder to provide video interfacing requirements.
-
product
Thermal Voltage Converter
1395B
The 1395B TVC. Has better thermal stability than it's predecessor. Measuring ac voltages between 20 Hz and 100 MHz with increased accuracy and reliability. The 1395B can be used as a primary ac voltage standard and/or standard for the calibration of ac calibrators and voltmeters.
-
product
Frequency Converters
Ducommun's frequency converter families include waveguide detectors (FAS), passive and active multipliers (FMP and FMA), up and down converters (FUB and FDB), harmonic mixers (FDH), subharmonically pumped up and down converters (FUS and FDS) and phase detectors and single sideband modulators (FPB and FSS). These devices are offered in 7 waveguide bands to cover entire 18 to 110 GHz frequency spectrum. These converters employ high performance GaAs Schottky beamlead diodes and DLT's proprietary circuit configuration to produce superior performance, such as low conversion loss and up to full waveguide instantaneous operation bandwidth.
-
product
Video Format Converter
RVG-FC1
Curtiss-Wright Defense Solutions
Video management integration is often complex and burdened with problems that arise from integrating legacy equipment with the latest video sources. The Curtiss-Wright Rugged Video Gateway Format Converter (RVG-FC1) provides a flexible building block capable of converting between a range of video formats and resolutions (15 different formats and resolutions are supported).
-
product
Single Phase Converter
Series Sirio AC / ACS
The SIRIO single-phase equaliser is an electronic device that offers the ability to regulate the rms value of a sinusoidal voltage through the control of two diodes connected in antiparallel.
-
product
Compact Converters
BrightEye
The BrightEye™ line of compact converters from Ensemble Designs takes advantage of the newest technology to bring you the best video and audio converters. With over 60 different BrightEyes to choose from, you’ll find the right unit for your video processing needs. The BrightEye line offers solutions for video routing, scan conversion, streaming, audio embedding, reference generation, video conversion, HDCP and more.
-
product
E/O Converter
LTX-510
The LTX-510 Electrical to Optical Converter is a convenient device that is intended to transmit analogue or digital signals to a remote location via a multi-mode fibre optic cable. The main applications are situations in which the signal of interest has a high common mode voltage with respect to the measuring equipment.
