Sensor Amplifiers
-
Product
Low Power Op Amplifiers (< 1mA/amp)
-
Analog Devices low power op amps offer a variety of benefits in many applications such as prolonging battery life, easing waste heat management in end equipment, reducing self heating to minimize thermally induced offset shift, and reducing total system power consumption and cost. Offering power efficient devices without compromising speed, noise, and precision has been a key focus on developing products at ADI.
-
Product
Instrumentation Amplifiers
HIGH-POWER RADIO FREQUENCY (RF) AND MICROWAVE AMPLIFIERS, TWTA AND SOLID STATE
-
Communications & Power Industries
Electromagnetic compatibility (EMC) high-intensity radiated field (HIRF) testing, military testing, electronic warfare simulation and scientific applications are based on the same switched-mode power supply technology as its rugged amplifiers. As a result, these instrumentation amplifiers have all the same performance and reliability advantages as the rugged product line, but have been neatly re-packaged into compact, lightweight and affordable rack-mountable units more suitable for less demanding physical environments. CPI TMD's new modular design (the PTCM range) has many user benefits, including advanced self-diagnostics, ethernet interfaces, remote management, VSWR protection and plug and play field replaceable power supplies.
-
Product
LINEAR AMPLIFIERS
F-series
-
The F-series amplifiers are designed to extend the output range of low voltage signal sources. They are general purpose devices with a very low output impedance, very fast response and high current. The output is linear from DC up to few megahertz range.
-
Product
Non-contact Sensors
SENSOR NAVI
-
The easy system check is a function that allows easy checking of the compatibility or incompatibility between products and accessories, but does not guarantee all combinations.- Since the information provided through this system consists of approximate estimates, Mitutoyo declines any responsibility regarding damages that may arise from such information.
-
Product
Remote Sensors
-
The most versatile and popular sensors we make. The ROS-W (Remote Optical Sensor with tinned wire termination) and ROS-P (Remote Optical Sensor with 1/8" phone plug termination) are threaded stainless steel remote optical sensors with a visible red LED light source. All these sensors have the "on-target" green LED indicator
-
Product
Single Channel High Voltage Linear Amplifier
F10A
-
The F10A is a general purpose broadband linear amplifier having a fixed amplification of 10 times and capable of bipolar high voltage output of ±100V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±10 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
Product
PWM Amplifiers
SA Series
-
Covering a power range of 5 to 20 KVA, the MCS line of high frequency PWM servo amplifiers utilizes the latest in solid state power circuitry and power devices to provide the greatest amount of flexibility available in the brushless motor drive market. The SA Series is a stand alone system with integral power supply designed for industrial application where the system will mount inside a NEMA type enclosure.
-
Product
Torque Sensors
-
TE Connectivity (TE) offers solutions for measuring reaction torque and rotating torque. Our torque meters, complete with integral mechanical stops, increase overload capacity and provide additional protection during mounting and operation. We offer a variety of small capacity sensors for dynamic and reaction torque measurements. Our combination sensors simultaneously measure reaction torques and forces with a single device; these sensors can also detect angle position and provide velocity measurement. We can customize a wide range of available models to meet your specific needs.
-
Product
Non Contact Temperature Sensors
-
Non Contact Type temperature measurement involves determining temperature of object surface without direct contact with the surface. Tempsens offers both single point and area inspection model devices which are infrared thermometers and infrared camera and industrial furnace monitoring camera.
-
Product
Amplifiers
-
Amplifiers are used to amplify the energy output of photodetectors as well as convert their electrical signal for a number of illumination measurement or spectroscopy applications. Amplifiers are digital systems that amplify the low electrical current transmitted by photodetectors to easily detectable levels. Amplifiers also convert photodetectors' electrical current into voltage so that their signal may be read by other digital devices. Amplifiers are indispensable for nearly any light measurement applications by greatly increasing the usability of a detector system.
-
Product
CGS500-IR NDIR Gas Sensor
-
The CGS500-IR sensor is a NDIR (non-dispersive infrared) sensor designed to replace thermocatalytic gas sensors for monitoring hydrocarbon gases in the range 0-100% LEL. The CGS500-IR is available as a sensor only or fitted in an EEx e certified junction box.
-
Product
Light Section Sensors
-
Leuze electronic GmbH + Co. KG
Switching light section sensors are designed to perform scanning, two-dimensional object detection along a laser line. They are especially well suited for completeness monitoring or product monitoring in the case of multiple track transport. The short measurement time and the detection range from 200 to 800 mm enable an inspection of the content at a high throughput rate even with deep containers. The internal data processing offers programming and differentiation of 16 different object types, thereby conserving control capacity. Complex detection tasks can be solved with one sensor. The compact housing ensures high flexibility during installation and saves installation space.
-
Product
Driver Amplifiers (< 3 W)
-
Qorvo's driver amplifiers are designed to provide good linear or efficiency performance for gain stages prior to the final power amplifier in a transmitter chain. These products support frequencies up to 46 GHz, using process technologies such as InGaP HBT, power pHEMT, E/D pHEMT and GaN.
-
Product
Meteorological Sensors
-
Automatic Weather Station, Wind Speed Sensor, Air Temperature Sensor, MIRA Visibility Sensor, Wind Direction Sensor, Air Pressure Sensor, Barometric Pressure Transmitter, Solar Radiation Sensor.
-
Product
Transparent Object Photoelectric Sensors
-
Contrinex Transparent Object Photoelectric Sensors
-
Product
Temperature Sensor
-
Precision temperature sensors from Stellar Technology are in demand worldwide for a variety of industrial test, measurement and process control applications.
-
Product
Lambda Sensor
KS60121
-
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
Product
2D CMOS Image Sensors
Emerald 36M
-
Superior 36 Megapixel resolution - 6K square resolution - Multi-ROI feature enabling more objects to be captured in a single high resolution shot - Small global shutter pixel for blur-free images.With its high resolution, Emerald 36M improves inspection accuracy, increases throughput through an optimized inspection system path, and covers wider areas for surveillance or aerial mapping.
-
Product
Amplifiers
-
Amplifier is designed to be used in conjunction with optional modules and can be confiugured for up to 8 inputs and 8 outputs. 9000 series modules as well as existing 900 series input modules can be used. The more appropriate modules can be selected depending on applications. Since it comes with two 60W power amplifiers, it can individually perform multi-origin braodcasts. It is equipped with singnal processing and control functions necessary for sound reinforcement, permitting all parameters to be set at the mixer. Settings data can be stored inside the unit and called up using the keys on the front panel.
-
Product
Quantum Cascade Laser Sensors
-
QCL sensors use mid-infrared semiconductor laser sources, either intraband Quantum Cascade Lasers or Interband Cascade Lasers to enable high precision, high accuracy, and selective detection of trace gases such as greenhouse gases and chemical agents with application to a variety of commercial, industrial, defense and environmental problems.
-
Product
Redox (ORP) Sensors
-
ORP sensors measure the oxidation-reduction potential—the tendency to gain or lose electrons when a solution comes in contact with a chemical substance. ORP measurements are used to ensure that a solution has been completely reduced or oxidized. ORP sensors are often used in tandem with pH sensors, which measure the hydrogen ion activity in a solution.
-
Product
Amplifiers
-
We have designed and manufactured amplifiers using all major semiconductor materials, LDMOS, GaN, GaAs, and InP, to produce narrow, wideband, and pulse, receive and transmit amplifiers from 1 MHz to 220 GHz and power levels from mW to over 10 kW.
-
Product
Acoustic Emission Sensors
-
Acoustic wave (acoustic emission) sensors are the ceramic piezoelectric transducers converting the mechanical elastic acoustic waves generated in the material (e.g. elastic waves occur when a material cracks, wears, deforms, or corrodes) to electrical signals. The electrical signals are then amplified and filtered by a preamplifier and then transmitted to a special acoustic emission acquisition instrument for further data processing and analysis.
-
Product
Portable Power Amplifier
PA30Bip-H
-
PA30Bip-H portable power amplifier is designed with linear amplifier principle. It is very light portable solution with three channels of current output and four channels of voltage output.
-
Product
Vibration Sensor
-
Remotely monitor the health of your equipment with 3560 FC Vibration Sensors. Obtain real-time vibration measurements through the Fluke Connect® Cloud via Fluke 3502 Gateway. Measuring imbalance and misalignment these sensors provide an early warning for equipment and sends alarms through the Fluke Connect Condition Monitoring software to a desktop or smartphone. This product requires a 3502 FC Gateway and Fluke Condition Monitoring software. Package comes with 10 sensors.
-
Product
Optical Speed Sensors
-
Allows use in a wide range of hazardous environments in petrochemical, Gas and volatile materials processing industries, ideally suited for Condition Monitoring, Data collectors in balancing applications, these sensors give excellent performance with repeatable results, engineered for easy mounting with the optional Mounting Bracket and Mini Tripod Stand in hand held applications.
-
Product
Wireless Sensor Nodes
-
Wireless technologies from ams are notable for their extreme high performance, low power consumption and small board footprint.
-
Product
Meteorological Sensors
-
A wide selection of premium meteorological sensors from our partners will allow you to log a wide variety of useful data.
-
Product
Dual Channel High Voltage Linear Amplifier
A400D
-
This unit contains two independent A400 amplifiers that share common ground reference and power supply.
-
Product
One-Piece Optical Sensor Head
OP
-
Sciences et Techniques Industrielles de la Lumière
OP series consists of a one-piece optical sensor head for dedicated applications (e.g. long distance).The performance and specifications are dedicated to various applications in the industry.Typically integrated as OEM for measuring 3D shapes, glass thickness, autofocus, OP series fits a wide range of applications.
