Category 5
Category 5 cable.
-
product
PXIe-4304, 24-Bit, 32-Channel, 5 kS/s, 42 V, PXI Analog Input Module
783867-01
24-Bit, 32-Channel, 5 kS/s, 42 V, PXI Analog Input Module—The PXIe‑4304 is a filtered analog input module for higher voltage measurements. The module offers the ability to select a digital filter per channel to provide extra filtering performance. You also can operate up to four different sample rates and triggering configurations concurrently to ensure you measure every sensor as needed. The module has an A/D converter per channel to enable a simultaneous sample rate at the maximum sample rate across the input range. The included NI‑DAQmx driver simplifies hardware configuration and measurement.
-
product
PXI 8 Slot BRIC 150x8 1-Pole (5 sub cards)
40-561A-121-150X8
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
5 ft Harness, 78-Pin Male Connector
GT96110
5 ft harness, 78-pin male connector on both ends
-
product
Multi-channel S-band Klystron 2.45 GHz / 5 MW
Insight Product Co. 's multi-channel S-band, 2.45 GHz, klystron provides up to 5.0 MW of output pulse power.
-
product
Active Probe, 5 Hz to 500 MHz
41800A
The Keysight 41800A Active Probe provides high input impedance from 5 Hz to 500 MHz. The Keysight 41800A is a valuable tool when used with a network and spectrum analyzer for circuit signal analysis.
-
product
PCIe-6509, PCI Express, 96-Channel, 5 V, TTL/CMOS, 24 mA Digital I/O Device
779976-01
The PCIe-6509 can directly drive external digital devices such as solid-state relays (SSRs). You can configure each port for input or output, and no external power supply is required for outputs. Using programmable power-up states, you can configure the initial output states in software to ensure glitch-free, safe operations when connected to industrial actuators. If a computer or application fault occurs, the PCIe-6509 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
product
PXI-2564 , 16-Channel, 5 A, SPST PXI Relay Module
PXI-2564 / 778572-64
16-Channel, 5 A, SPST PXI Relay Module—The PXI‑2564 is a general-purpose switch module that features independent single‑pole single‑throw (SPST) Form A armature relays. Each relay is nonlatching with very low on-resistance and low thermal offsets. The PXI‑2564 is fully software programmable. With an efficient coupling of voltage/current capability and relay density, this switch module is ideal for switching medium‑ to high‑power signals and loads in military, automotive, or automated test applications.
-
product
SH96F-96M-5, Shielded Cable for PXIe-4330 and PXIe-4331 to Rackmount Terminal Block, 5 Meter
786341-05
Shielded Cable for PXIe-4330 and PXIe-4331 to Rackmount Terminal Block, 5 Meter
-
product
4 & 5 Pin Trailer Circuit Tester
PT7866
Traces each lighting function to the terminal in question. Plugs into the trailer plug. Each LED light corresponds to the circuit being energized. Provides an easy to connect ground terminal for trailer lighting set-up.
-
product
PCIe 16 Bit Multi-purpose Digitizer - up to 5 MS/s on 8 Channels (Single Channel) or 4 Channels (Differential)
M2P.5913-X4
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
product
PXI/PXIe Power Relay Module, 8xSPDT, 5 Amp, 50-Pin SGMC Connector
42-158-004
The 40/42-158-004 is a PXI/PXIe high density power relay module with 8xSPDT switches rated at 5A. User connection is via a 50-pin SGMC male connector.
-
product
Prep HPLC & SFC Columns - 5 µm Spherical Particle Size
RediSep Prep
When you need the highest purity compound, the first choice in laboratories worldwide is Teledyne LABS RediSep Prep columns. Durable RediSep Prep columns are specifically designed to provide quick, accurate results to fulfill your High-Performance Liquid Chromatography (HPLC) and Supercritical Fluid Chromatography (SFC) needs.
-
product
PCI Express 5 CEM Receiver Test Automation
N5991PC5A
The N5991PC5A is the receiver test automation software for bit error ratio testers, allowing you to test, debug and characterize PCI Express 5.0 CEM Add-In Cards and systems.
-
product
Signal, Patchcord, ITA, 36", QuadraPaddle, (5 Amp), 26 AWG Twisted Pair White/Black (1.5 Amp)
7-123426000-036
Signal, Patchcord, ITA, 36", QuadraPaddle, (5 Amp), 26 AWG Twisted Pair White/Black (1.5 Amp).
-
product
ATE System Power Supply, 300 V, 5 A, 1500 W
N5771A
The single output, 1500W N5771A provides universal AC input, GPIB, LAN, USB, LXI compliance, and analog/resistance control of output voltage and current.
-
product
PXI 8-Slot BRIC Matrix, 55x16 1-Pole (5 sub-cards)
40-562B-121-55X16
The 40-562B-121-55X16 is a high density BRIC8 matrix module with a size of 55x16 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
Blank, Module, Receiver/ITA, 90 Series, 5 Positions
510104144
Blank modules are placed in unused module slots and cover empty slots to help prevent debris entrance into the rack. Blank modules fit in either ITA or receiver positions.
-
product
5 kW and 10 kW RP7900 Series Regenerative Power System
RP7900 Series
The RP7900 Series regenerative power system is a family of 5 kW and 10 kW bi-directional, regenerative DC power supplies that reduces the cost of test with highly integrated capabilities. The regenerative capability enables the energy consumed to be put back onto the grid cleanly, saving costs from energy consumption and cooling, while not interfering with the grid. The RP7900 helps you overcome your toughest power test challenges by delivering industry-leading specifications and innovative features in an integrated solution for today's advanced high power automated test equipment (ATE)power testing needs. The RP7900 provides the fastest, most accurate, integrated regenerative power system.
-
product
PXIe 8 Bit High Speed Digitizer - 5 GS/s on 1 Channel, 2.5 GS/s on 2 Channels, 1.5 GHz Bandwidth
M4X.2233-X4
The 9 models of the M4x.22xx-x4 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
product
Multimeter 5 in 1 Environmental Multimeter with Lux Sound Level Humidity Temperature
VA19
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
VA19 5 IN 1 multifunction multimeter This multimeter combined with temperature, humdity, lux and sound lever in one meter.
-
product
PXI 4 Slot BRIC 220x4 2-pole (5 sub-cards)
40-562A-022-220X4
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
PXIe-6509, 96-Channel, 5 V, TTL/CMOS, 24 mA PXI Digital I/O Module
787358-01
PXIe, 96-Channel, 5 V, TTL/CMOS, 24 mA PXI Digital I/O Module - The PXIe-6509 can directly drive external digital devices such as solid-state relays (SSRs). You can configure each line for input or output and you also can configure each line with a user-configurable pull-up or pull-down resistor. Using the PXIe-6509 programmable power-up states, you can configure the initial output states in software to ensure glitch-free, safe operations when connected to industrial actuators. The PXIe-6509 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. The PXIe-6509 provides programmable input filters for eliminating glitches or spikes and for debouncing digital switches or relays through a software-selectable digital filter.
-
product
PXIe-5162, 1.5 GHz, 5 GS/s, w/CableSense, 10-Bit PXI Oscilloscope
782622-16
PXIe, 1.5 GHz, 5 GS/s, 10-Bit PXI Oscilloscope—The PXIe-5162 high-speed oscilloscope device has two or four channels that sample at up to 5 GS/s with flexible settings for coupling, voltage range, and filtering. PXI Oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with fast signals that require up to 1.5 GHz of analog bandwidth and flexible measurement configurations.
-
product
PXI 8 Slot BRIC Solid State 160x8 1-Pole (5 sub-cards)
40-563A-121-160X8
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance PXI matrix requirements and are constructed using solid-state switches. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
PCB Adapter, Receiver, VTAC, to (2) USB 5 Gbps (USB 3.0, USB 3.1 Gen 1, USB 3.2 Gen 1) and (4) RJ45 Connectors
510170114
Mates with p/n 510171114.Please note: The RJ45 connectors extend beyond the width of the module. Care should be taken when installing in positions adjacent to other PCBs. Please contact VPC, if further assistance is needed.
-
product
PXI 4 Slot BRIC 220x4 1-Pole (5 sub-cards)
40-562A-021-220X4
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays.
-
product
VTAC, Patchcord, Receiver, 72", VTAC, USB 3.0, To USB 5 Gbps (USB 3.0, USB 3.1 Gen 1, USB 3.2 Gen 1) Type A Male
7-142890690-72
VTAC, Patchcord, Receiver, 72", VTAC, USB 3.0, To USB 5 Gbps (USB 3.0, USB 3.1 Gen 1, USB 3.2 Gen 1) Type A Male.
-
product
PXIe-5162, 1.5 GHz, 5 GS/s, 10-Bit, 2GB mem, Oscilloscope
782622-15
PXIe, 1.5 GHz, 5 GS/s, 10-Bit PXI Oscilloscope—The PXIe-5162 high-speed oscilloscope device has two or four channels that sample at up to 5 GS/s with flexible settings for coupling, voltage range, and filtering. PXI Oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with fast signals that require up to 1.5 GHz of analog bandwidth and flexible measurement configurations.
-
product
PCB TA01, 5 mV/g, IEPE, Accelerometer, Triaxial Vibration Sensor
780990-01
5 mV/g, IEPE, Accelerometer, Triaxial Vibration Sensor - The PCB TA01 helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound and Vibration Input Modules, and USB-based Sound and Vibration Devices. This sensor uses the Integrated Electronics Piezo-Electric (IEPE) current excitation. The PCB TA01 features a sensitivity range of 5 mV/g.
-
product
Signal, Patchcord, ITA, 72", QuadraPaddle, 26 AWG White, Single Ended ( 5 Amps)
7-123926000-072
Signal, Patchcord, ITA, 72", QuadraPaddle, 26 AWG White, Single Ended ( 5 Amps)
