Non-contact Voltage Testers
check for presence of electricity.
-
Product
High Voltage DC Personal Tester
DC/PT 75
-
Within a matter of seconds you can measure for yourself whether a voltage exceeding 750V is present. Used on voltages up to 75kV DC to earth.
-
Product
Toe Compression Tester
UI-FT03
-
Safety Shoe Toe Cap Compression is to test toe cap compression resistance ability.
-
Product
Digital Igniter Tester
Alpha 4314KRC
-
The Alpha 4314KRC Digital Igniter Tester packaged per NSN 6625-01-460-1499.
-
Product
Solar Cell Testers
-
Solar Cell Testers are integrated systems incorporating Solar Simulator and I-V Measurement systems. PET offers Standard and Advance IV Measurement software. PET Cell Testers are capable of measuring a diverse range of solar cell parameters such as Isc,Voc, Imax,Vmax, Pmax, FF, Rsh, Rs and η cell conversion efficiency, complete light and dark I-V curves. All that needs to be done to test a cell is to load the cell, make electrical probes contact and press “Measure” icon on the I-V Measurement System software. The software will automatically open the Solar Simulator shutter, perform the test and close the shutter after the test is complete. The design is modular in nature and can be easily upgraded. Some options can added at a later time.
-
Product
Relay Tester
PTE-50-CE
-
The reversible 100-VA amplifier can inject up to 50A or 150V with outstanding stability, free of distortions and completely isolated from the power supply. The waveform is synthetized electronically and can generate harmonics from 1st to 7th of the supply’s frequency. Various output ranges are available to maintain the 100VA power throughout the entire settings scale. The system features automatic protections against overload and overheating.
-
Product
Digital Clamp Tester
MCL-550D
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・55mmφCT window and Multi Function・AC Line Current up to 1000A・AC/DC Voltage, Resistance, Continuity Check & Diode Test・Conform to IEC safety requirements (IEC1010-1, CAT III 600V)
-
Product
Moisture Testers
-
Wuxi IMHOO Technology Co., Ltd.
Used to measure the percentage of water in materials like wood, drywall, concrete, and soil.
-
Product
Fully Automatic Non-contact Sheet Resistance Measurement System For Flatpanel Display
NC-60F/RS-1300N
-
*Global standard for non-contact measurement of ITO film, Metal thin films on flat panel*Automatic X-Y and Z (eddy current probe head) axis moving mechanism*Compatible with Loading robot for fully automatic measurementOption :*Integlate to combined system (film thickness meter, etc)*Add 4 point probe measurement unit : RT-3000
-
Product
RF PHY Tester
TLF3000
-
TLF3000 RF PHY tester is a wideband, ultra-high dynamic range 2.4 GHz software-defined receiver, signal analyzer and signal generator. It captures and analyses the entire 2402-2480 MHz band simultaneously providing RF PHY testing, signal generation, signal analysis in one powerful package.
-
Product
Process Voltage & Current Data Loggers
-
Monitor and log virtually any process voltage or current output from your transducers.
-
Product
NBS Abrasion Tester
UI-FT40
-
NBS Abrasion Tester is used to test rubber abrasion resistance and to know material nbs abrasion index. NBS abrasion test is suitable for vulcanized rubber used for soles and heels of footwear. Unuo NBS Rubber Abrasion Tester is designed and applicable according to ASTM D1630. Here for More Abrasion Tester.
-
Product
Multifunction Tester
M70
-
M70 is a mobile device dedicated to measuring Insulation resistance with test voltage up to 1000VDC and Continuity of protective and equipotential conductors with current of 200mA in private and industrial electric installations.
-
Product
Oil Tester
-
AJIT Transformer Oil Set is completely self contained, compact & portable unit giving smooth variable output voltage from zero to 60/80/100KV for testing the dielectric strength of insulating oil.
-
Product
Film Permeability Tester
-
Film Permeability Tester is designed to test the permeability of a wide range of packaging materials such as plastic film, composite film, aluminum foil, thin sheets, rubber, porcelain, medical patch, etc.
-
Product
Voltage Meter
МН32СМ
-
The mezzanine module (mezzanine) МН32СМ is designed to measure instantaneous voltage values over thirty two two-wire differential channels.
-
Product
110-125V Receptacle Tester
1938
-
Peaceful Thriving Enterprise Co Ltd
Test for 110-125V AC circuits. Detect faulty wiring in 3 wire receptacle.
-
Product
Resistance Tester
KT-2000RD
-
This equipment represents the wanted resistance value in digital figures and at the same time, is an ohmmeter which decides products to be bad in case of being out of the previously set range of H,L and to be good in case of being within the range. Moreover, because it is designed and manufactured on the basis of KAST's business experiences and know-hows accumulated through on-the-spot works for a long time, it is highly trustable, especially strong to noise and impulse that occur on the bad electric condition of on-the-spot or on the connection with any other equipments, and also is convenient for use.
-
Product
3-Phase AC Voltage Transducer
ENVIROMUX-PT3-600
-
Monitors and reports voltage of any 3 phase circuit. Remotely detect blown fuses or tripped circuit breakers. Three 600 VAC inputs, three 4-20 mA outputs. Inputs and outputs isolated from one another. Frequency: 50/60Hz. Maximum primary current: 600 volts. Accuracy: ±0.25% F.S. @60Hz. Output: 4-20 mA. "Zero" adjustment for accurate 0 VAC reading, and "Calibration" adjustment for frequency and voltage level. Powered by the ENVIROMUX-S420MA-24V. Regulatory approvals: UL, CUL, CE. Requires two ENVIROMUX-S420MA-24V to monitor three phases. Caution: installation should be performed by qualified electricians only. Make sure electrical service is disconnected before making any electrical connections.
-
Product
Tensile Tester
-
Wewon Environmental Chambers Co, Ltd.
Is a fundamental materials science test in which a sample is subjected to a controlled tension until failure
-
Product
High Voltage Dividers
-
Ohm-Labs manufactures precision resistive high voltage dividers. By individually characterizing each resistor in the divider, voltage and power effects are minimized.
-
Product
Reel to Reel Non-Contact OS Inspection System for TAB/COD/TCP/TBGA
TRV
-
*Most suitable mechanism for non-contact inspection*Sprochet-less transfer decreases products damage.*Easy operation by Fixture alignment mechanism*Equipped with Tracing Test function
-
Product
Hardness Tester
NB3010 Series
-
Newage Testing Instruments, Inc.
A basic Brinell hardness tester with semi-automatic operation. NB3010 is a cost-effective Brinell tester using deadweights with a pneumatic load system to apply and remove the loads. Operates in most all Brinell scales.
-
Product
Thermal Voltage Converter
1395D
-
The 1395D series of TVC's, have Dual Thermal Element technology. The 1395D offers double the output voltage (typically 14 mV instead of 7 mV). This higher output voltage means better resolution and increased accuracy. It can be used to measure AC Voltages between 20 Hz and 100 MHz and it can serve as a primary AC voltage standard and/or standard for calibration of AC calibrators and voltmeters.
-
Product
Non-contact Sensors
SENSOR NAVI
-
The easy system check is a function that allows easy checking of the compatibility or incompatibility between products and accessories, but does not guarantee all combinations.- Since the information provided through this system consists of approximate estimates, Mitutoyo declines any responsibility regarding damages that may arise from such information.
-
-
Product
Macro Hardness Testers
-
Macro hardness is the measurement of the hardness of materials tested with high applied loads.
-
Product
Signature Surge Testers
TS Model
-
Although all PJ Surge Testers are capable of testing 3 Phase Motors, this "TS" Model has the same characteristics as the Signature Model (rack-mounted, Tektronix TDS1002, 1 Billion Samples/sec, real time, programmable, storage oscilloscope) but includes a built-in 3 phase test selector switch that facilitates 3 phase motor testing by mechanically re-positioning the ground terminal.
-
Product
Generator Of Direct Current And Voltage
GPTN
-
The module is intended for use as part of information measuring systems based on the VXI-bus trunk. The module is designed to generate constant current or constant voltage.
-
Product
Safety Testers
-
Safety testers (also named hi-pot tester/hipot tester/hipot test) are designed to ensure safe operation of DUTs under various operating conditions and environment.
-
Product
Hail Impact Tester
HIT
-
Hailstorms can cause severe damage to modules and collectors. Our test stand enables you to carry out tests according to international standards. The hail impact test stand uses an air-pressurized launcher that shoots ice balls representing hailstones of a predetermined size at the module or collector mounted on the support frame.
