Optical Coherent Tomography
-
Product
Optical Fiber Identifier
X5004
-
Lower power indicationEasy-to-replace adaptersEasy-to-use with "ONE KEY" operationDisplays the relative core powerDurable metal housing and quality constructionEfficiently identifies the fiber transmission direction and frequency tone (270Hz, 1 KHz, 2 KHz) with audible warning
-
Product
O.E.M. Optical Standards
-
O.E.M. Optical Standards by Applied Image - Boston Scientific Checkerboard Array, Cognex Glass Calibration Plate Set
-
Product
Optical Touch Switch
SW-100
-
Panasonic Industrial Devices Sales Company of America
The SW-100 Optical Touch Switch is an ergonomically designed start-up Switch that is activated simply by touching it for greater convenience and less stress on the hands.
-
Product
Optical Device
-
Optical devices are products that use the optical characteristics (birefringence) of quartz crystals. Murata Manufacturing uses high-precision synthetic quartz crystals grown using our proprietary technology to manufacture high-grade products.
-
Product
Active Optical Cable
-
Shanghai Tarluz Telecom Tech Co., LTD
Are cables with optoelectronic modules in the connector heads that convert electrical signals to light.
-
Product
Optical Communication Probes
-
Abacus Electrics ANSI Type 2 optical probes utilize infra-red LED technology to provide a galvanically isolated, bi-directional communications interface between energy meters and laptop computers or handheld devices for onsite data retrieval, programming and diagnostics.
-
Product
Optical Active Module
-
UPM (Universal SFP-Typed Power checker Module) provide very high productivity for power checking work on high density fiber optic systems and devices for FTTH, CWDM-PON and local network systems. UPM can measure optical power intensity.
-
Product
Optic Node
OX 752
-
Converts even weak Optic Signals to a high quality RF Signal. LED BAR Optic Level Display has been provided for ease of system maintenance. They are best suitable for Analog as well as Digital transmission to maintain BER, MER Characteristics.- High Quality Nodes- Frequency 40 ~ 1000 MHz- Good Sensitivity of -11 dBm- RF O/P 110 dBµV at 0 dBm Optic I/P- High Voltage Surge Protection- LED Optic Level Display- Powder Coated Housing
-
Product
3D Optical Microscopy
-
Bruker is the worldwide leader in 3D surface measurement and inspection, offering fast, non-contact analyses for samples ranging in size from microscopic MEMS to entire engine blocks. Our microscopes are the culmination of ten generations of proprietary Wyko® Technology advances that provide the high sensitivity and stability necessary for precision 3D surface measurements in applications and environments that are challenging for other metrology systems.
-
Product
Electrical Tomography Software
Res2dinv
-
This very popular software, developped by M.H.Loke, uses the method involving the Sasaki minimum squares inversion (1992) to produce a 2D sub-soil model starting from the data of apparent resistivity (up to 2000 electrodes). It is completely automatic and does not require that the user formulates a starting model. When using a state-of-art computer, the inversion of a single pseudosection will require only a few minutes.RES2DINV supports spreading types like Wenner, Schlumberger, Pole-Pole, Pole-Dipole, line Dipole, equatorial Dipole and other non-conventional spreading types.
-
Product
Optical Spectrum Analyzers
FTBx-5245/5255
-
Robust In-service Pol-Mux OSNR for 100G/200G/400G (FTBx-5255). Industry’s only all-in-one OSA covering all applications: high speed (100G+ In-service OSNR, etc.), CWDM, O and L-band testing, etc.Portable solution for spectral characterization of DWDM/CWDM networks. Industry’s smallest OSA/transport solution in a single platform (FTB-4 Pro). Pol-Mux OSNR option compliant with IEC 61282-12 standard.
-
Product
Optics
-
Rising from our Qioptiq® heritage, Excelitas now offers precision optics in most every form and spanning the entire spectrum. You can choose from more than 4,800 off-the-shelf optical products! Our selection includes plano-convex lenses, biconvex lenses, aspheres and achromats with individual coatings, as well as plano optics, mirrors, polarization optics, electro-optics and optical design software and of course our optical assemblies and systems, such as objective lenses, optronics modules, and complex custom sub-assemblies and turn-key systems.
-
Product
Custom Optical Lenses
-
Since 2006 we have developed over 100 custom lenses for various lighting industry according to specific regulation and standards. From optical design, high accuracy optical tools till production of custom lenses, DBM offers the best guarantee of results as all steps are managed under the same roof.
-
Product
Optical Modules And Components
-
Luna offers a complete line of high performance active and passive fiber optic modules and components for a wide range of fiber optic systems, including interferometric systems for fiber optics sensing, fiber optic gyroscope (FOG) and optical coherence tomography (OCT).
-
Product
Optical OTDR
TLM-01D
-
Hangzhou Tuolima Network Technologies Co., Ltd.
OTDR-01D series handheld optical time domain reflectometer (OTDR) is a new generation of intelligent optical measuring instrument designed for the optical fiber communication system testing by TUOLIMA Network Technologies Co., Ltd.. This product is mainly used to measure the parameters of optical fibers and cables, such as length, loss, and connection quality, etc.; it can realize the accurate positioning of event points and fault points, and can be widely used in the construction, maintenance testing and emergency repair of the optical fiber communication systems as well as the research, production and production measurement of optical fibers and cables and so on. This product can provide you with the highest performance of solutions for installation and construction of fiber optic network construction and the subsequent fast and efficient maintenance and troubleshooting testing.
-
Product
Optical Test Lab
-
Every object affects or interprets light differently, so appropriate and accurate measurements are needed in order to determine how much light is being produced by a source or cast upon an object. This can be measured with respect to power requirements, as well as how the human eye interprets that light.
-
-
Product
Optical Sensors: Fluorometers
-
Sea-Bird Scientific offers a wide variety of fluorometer configurations and measurement capabilities. ECO fluorometers are available in single, dual, and three-measurement combinations. Fluorometers measure chlorophyll-a, FDOM, rhodamine, phycocyanin, and phycoerythrin.
-
Product
X-ray Optics
-
Do you want to shape your X-rays to a tiny point? Then our X-ray optics can help you. Benefit from 30 years of know-how in the development and manufacture of customized optical components for demanding applications. Our high-precision optics offer unsurpassed performance and enable the best results in a wide range of applications.
-
Product
Optical Modulation Analyzer
OMA
-
In partnership with Tektronix, we bring you a high-performing and flexible OMA system that will meet your requirements today and into the future.With the market-leading performance of Quantifi Photonics’ IQRX coherent receiver and the scalable architecture of Tektronix’s high-performing oscilloscopes, you’ll get the most out of your investment. Use the stack as a single 70GHz OMA system, or use it as four independent oscilloscopes.Whether you are working with 100G coherent transceivers or 1 Terabit long haul communication systems, our OMA can be configured to suit your exact requirements.
-
Product
Optical Fiber Microscope
-
Connector-end face contamination is a problem that shouldn’t be ignored when it comes to fiber optic cables and patch cords. Allowing contamination to take place or fester will lead to network issues and down-time which you don’t need. For any fiber optic cable network, a high quality fiber microscope is a necessary tool to identify where contamination may be presenting.
-
Product
Optical Benches
-
There are two types of SPHEREA optical test bench, Autonomous, to meet very specific needs, Combined with a versatile bench, to enable multiple-system testing.
-
Product
One-Channel Variable Optical Attenuator
N7761A
-
The N7761A attenuator is an extension to Keysight's high density N77xx-family that establishes a new standard in space-saving fiberoptic instrumentation.
-
Product
Optical Inspection System
OIS Products
-
A manual optical inspection system that is able to inspect the wire-bonded leadframe or substrate.
-
Product
Optical Profilers
-
Finally, measurements of surface roughness and topography can be made for a price that's less than that of a stylus profilometer. The Profilm3D has sub-nanometer vertical resolution, which surpasses optical profilometers that cost 3x as much. It does so by using the same state-of-the-art measurement technologies as the most sensitive optical profilers available: vertical-scanning interferometry (VSI) and phase-shifting interferometry (PSI).
-
Product
Optical BGA Inspection
-
Imaging hidden solder joints of BGA, IBGA, FlipChip, CSP, CGA and SMD components
-
Product
Optical Fiber Sensors
-
Optical sensors based on Fiber Bragg technology (FBG) are a reliable and safe solution for numerous testing applications, such as in structural testing and lightweight construction. Benefit from perfectly-matched measurement chains when using an optical FBG sensor based on Fiber Bragg Gratings made by HBM FiberSensing.
-
Product
Optical & Vision Systems
-
Usually made up of every component that is needed to acquire and analyze an image in order to perform the intended task.
-
Product
Optical Power Meter with Optical Head
GM8012 + 2 X GM8300X
-
The UC8820 + 2 X UC8820X optical power meter with optical head offer superior performance for the test of DWDM components, AWG & PLC components, optical amplifiers, and other general purpose of fiber optical test and measurement applications. It is special design for volume production line application.
-
Product
Optics Test Systems
F Number Meter
-
Optik Elektronik Gerätetechnik GmbH
The f-number of a camera lens is defined as the quotient of the focal length f' and the diameter of the entrance pupil. The f-number measuring device is a simple structure for the automatic, software-controlled measurement of the f-number of optical systems.
