-
Product
30 Amps, 100 MHz BW Current Probe - AC/DC , 50 Amp Peak Pulse
CP031
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
Product
Form A Circuit Board 80 Channel, 300 VDC, 2 A
OTP2 module no.195
-
The 40-139 2A relay series is suitable for applications requiring medium power, high density switching. With a current capacity of 2 A and voltages up to 300 VDC / 250 VAC, it is suitable for cost-critical applications.
-
Product
50-Pin SGMC Connector & Cable Accessories
-
Our 50-Pin SGMC connector is used on PXI power switching products to provide a high current user connector solution with high density.
-
Product
Cable Tracer and Phone Tester (2 in 1)
183 CB
-
Standard Electric Works Co., Ltd
Cable Tracer: Trace wires or cables. Volume control. Tip & Ring identification. 2 bi-colored LEDs ( Line 1 & Line 2). Tone speed selection : Fast & Slow. A phone jack is designed for headset or handset. (Amplifier probe)Phone Tester: Continuity and resistance testing for voltage-free objects. Check direct and alternating voltages. Testing capacitors. Testing diodes. Power ON/OFF switch. The indication of the LED lamp and the sound of the buzzer can occur at the same time. The LED indication for Power ON status.
-
Product
8x4 Power Matrix, 2-Pole, 2xGMCT
40-550-902
-
This version of the 8x4 power matrix is for heavy current/low duty cycle power switching. Connections are made via a front panel 37-way D-Type male connector or two 20-way GMCT male connectors. Used for switching inductive/capacitive loads up to 5A at 250VAC. Power matrix modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids. Used for applications requiring switching of either mains voltage or direct current.
-
Product
LXI Mainframes
-
The EX1200 family is the highest density switch and data acquisition instrument on the market with the ability to mix low-level, power, and RF switch modules in a single mainframe. This scalable family of products is designed to leverage capital investments in one common hardware and software platform that can be used in development, manufacturing, and field service. Mix and match a variety of modules to build a comprehensive signal switching subsystem that can be supplemented with precision analog and digital I/O modules.
-
Product
Saluki SEL8 Series Programmable DC Electronic Load (up to 200KW)
-
The new SEL8 series programmable DC electronic load is a new generation product designed by Saluki Technology. Incorporating high-performance chips, the SEL8 series delivers high speed and high accuracy with a resolution of 1mV and 1mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs).SEL8 series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar cell and fuel cell etc. test and measurement applications.* Customization available upon request
-
Product
Electronics Functional Test
-
Functional test for productive manufacturing. Manufacturers of products enabled by electronics must assure proper operation prior to shipment. Bloomy’s line of universal test systems are ideal for functional test of your PCBAs and subassemblies, from the simplest to the most complex. The UTS family of products combines high-performance test instruments, switching, power control and mass-interconnect hardware with our robust UTS software suite into a low-risk, cost-effective and powerful test solution for your device under test (DUT).
-
Product
PXI 2A 32xSPST High Density Power Relay Module
40-137-101
-
These Power Relay Modules are suitable for applications requiring power relay switching with high density. This version features 2A current and voltage to 110VDC/250VAC, they are configured as Single Pole Single Throw (SPST). Connections are made via front panel mounted 37 or 78-pin D-Type connector.Along with this 32 x SPST version, the range also includes a 39 x SPST, 2A version and a 16 x SPST, 5A version - go to Also in the Range above to learn more.Typical applications will be found in Automotive Test, Aerospace Test and Power Cell Test applications.
-
Product
Switchig Power Supply For LED Products
CX-P30
-
Shenzhen Chuangxin Instruments Co., Ltd.
switchig power supply for LED productsThis serial single output switch power supply is a kind of DC regulated power supply with high efficiency and stability.
-
Product
PXI Solid State Switch Module, 3xSPST, 10 A, Hardware Interlock
40-182A-012-HI
-
The 40-182A-012-HI has 3 off high current SPST switches with hardware interlock in one PXI slot and is part of our range of high power solid state switching solutions.
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-600B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
Product
Switches-SP5T
-
Macom Technology Solutions Holdings Inc.
At MACOM we offer an extensive collection of switches covering multiple commercial and aerospace and defense markets. Our product portfolio has a broad frequency spectrum from DC to 70 GHz. Our silicon Heterolithic Microwave Integrated Circuit (HMIC) PIN diode process is ideal for high power and broadband switches operating from 50 MHz to 26 GHz. Our AlGaAs PIN diode process can extend the upper frequency range of our switch die beyond 70 GHz and is ideal for instrumentation and radar applications. Our GaAs pHEMT and MESFET technology is ideal for fast switching and low control voltage switches optimized for both narrow band and broadband applications. Our 75 Ohm absorptive switches are designed specifically for demanding CATV, FTTx and DBS Infrastructure and CPE applications.
-
Product
Power-Switching Test System
High Voltage Switching Test System
-
The Accel-RF Power-Switching Test System is capable of measuring reliability under a variety of conditions for switching power applications up to 1kV (off) and 25A (on) at rates up to 1MHz switching frequency, dependent on voltage. By leveraging technology developed for the RF burn-in tray platform with new fast switching measurement techniques, this system can support testing of multiple devices under elevated temperature stimulus in a small physical area, and offers the flexibility to test both soft- and hard-switching applications. The Accel-RF Power-Switching System is the most flexible and accurate power switching platform available.
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-200B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
Product
6-Port Hardened Industrial Gigabit Ultra PoE DIN-Rail Switch
TI-UPG62
-
4 x Gigabit Ultra PoE ports2 x dedicated SFP slots240 watt power budget12 Gbps switching capacityHardened IP30 rated metal switchIncludes DIN-rail and wall mountsExtreme -40 to 75 ºC (-40 to 167 ºF) operating temperature rangeDual redundant power inputs with overload current protectionAlarm output triggered by power failurePower supply sold separately (TI-S24048)
-
Product
PXI Twelve 2:1 High Voltage Power MUX
40-331-006
-
The Pickering Interfaces 40-331/332 High Voltage Power Multiplexer and Matrix Modules are suitable for applications requiring high voltage power relay switching with high density. They feature current handling up to 5A, 1000VDC/1000VDC peak cold switching and 110VDC/250VAC hot switching. The 40-331 is available as a single 24:1, dual 12:1, quad 6:1, hex 4:1, octal 3:1 or twelve 2:1 multiplexer, and the 40-332 is available in 12x2 or 6x4 matrix configurations. Connections are made via a front panel mounted 37 pin high voltage D-Type connector.
-
Product
Radio Frequency (RF) And Microwave Products
-
Enable your 5G, aerospace, defense, test and measurement or industrial RF wireless applications with our portfolio of RF and microwave devices. These include high reliability RF diodes, Gallium Nitride (GaN) and Gallium Arsenide (GaAs) Monolithic Microwave Integrated Circuit (MMIC) amplifiers, frequency translation and power transistor devices, switches, attenuators, varactors, filters and more.
-
Product
PXIe Power Relay Module, 12xSPDT, 16 A
42-161A-101
-
The 40/42-161A-101 is a PXI/PXIe 12xSPDT power relay module and is part of a range of high density power switching solutions with a choice of SPST, and SPDT relay configurations with or without hardware interlock.
-
Product
PXI 2A Relay Module 52xSPDT
40-139-201
-
The 40-139 2A Relay Series is suitable for applications requiring medium power switching with high density. Featuring 2A current capacity and voltages to 300VDC/250VAC it is useful for cost critical applications.
-
Product
600-Watt DC/DC Converter, 6U VME
64PS1
-
The 64PS1 is a 600 Watt DC/DC Converter that plugs into a 6U VME chassis with an 0.8” slot. It is conduction-cooled through the card edge/wedgelock. This switching power supply accepts a +28 VDC input and provides a single output at 600 Watts continuous or 1,000 Watts peak.
-
Product
PXI Solid-State SPST Switch, 3-Channel 25A 100V
40-184-002
-
The 40-184-002 has 3-off high current SPST switches in one PXI slot and is part of our range of high power solid state switching solutions. Each SPST switch uses a fully isolated solid-state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation.
-
Product
PXI-2586, 10-Channel, 12 A, SPST PXI Relay Module
778572-86
-
10-Channel, 12 A, SPST PXI Relay Module—The PXI‑2586 is a general-purpose switch module that features independent single‑pole single‑throw (SPST) Form A armature relays. Each relay has low contact resistance and high isolation voltage. The PXI‑2586 is fully software programmable. It is rated for both high currents and high voltages, so it is ideal for switching power signals and loads in control applications and battery, power supply, and automotive testing.
-
Product
8-Ch SPST 20A-250VAC High Current
YAV90087
-
8 power relays Switching 20A 250Vac PNP Outputs para control or YAV90304 control CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
Product
Bench Power Supply, Switching DC, Adjustable, 1 Output, 0 V, 12 V, 0 A, 30 A
T3PS11230
-
Bench Power Supply, Switching DC, Adjustable, 1 Output, 0 V, 12 V, 0 A, 30 A.
-
Product
16-Ch SPST 10A-277VAC High Current
YAV90086
-
16 power relays SPST Switching up to 2770VA 16A Switching 125Vac 10A Switching 277Vac CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
Product
DataComm & LAN Testers
-
Tests & troubleshoots voice communication for open circuits, shorts, miswires, reversals, and split pairsSHIELD detection tests a cable’s shield integrityEasy to read fault display and high speed testingDebug mode for detailed fault identification resultsNetworking Cable Tester has auto sleep mode and power off switch to decrease power consumptionBattery low LED indicator
-
Product
16FE + 2GE Combo Port Unmanaged Switch
EKI-2718E-2CI
-
Provides 16FE+2GE combo port with Auto MDI/MDI-X, Supports 16 x 10/100 Mbps Auto-Negotiation + 2 x Combo 10/100/1000M Auto-Negotiation, Supports redundant 12 ~ 48 VDC power input.Supports DIP Switch Configuration: QoS/BSP/port-based VLAN.
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-1000B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
Product
100-Watt DC/DC Converter, 3U cPCI
55LQ2
-
NAI’s 55LQ2 is a 100 Watt DC/DC Converter that plugs directly into a standard 3U cPCI chassis with a 0.8” slot. It is conduction-cooled through the card edge/wedgelock. This modular, switching power supply accepts +28 VDC input and provides a single output at up to 100 Watts.
