AC Load Banks
source for testing and measurement of current, voltage and frequency.
See Also: Load Banks, DC Load Banks, Inductive Load Banks, Reactive Load Banks, Resistive Load Banks, UPS
-
product
AC Voltage Proving Units
HLV-2
Standard Electric Works Co., Ltd
The AC Voltage Detectors and AC Voltage Testers utilized to determine if the devices under test are functionally working. They are not a calibrator and cannot be utilized for calibration.
-
product
Loadpin Load Cell
LP
Designed to replace pins or bolts that carry a loadStainless steel constructionCapable of 100% humidity, 30G mechanical shock and 5G vibrationUsed with clevises, or pulley shafts to monitor loadsCapacity 1,740 lbf
-
product
PXI 4 Banks of 20 Channel 2 Pole MUX
40-615-022-4/20/2
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
product
AC Voltmeter/Noise Meters
The AC Voltmeter is high sensitivity voltmeter with 10µV full scale which nearly the limit of the measurement by the analog technique.And its frequency characteristic is suitable for measuring audio signal etc.
-
product
DC-Powered, AC Voltage Monitor
VAD/VQD
NAI’s VAD and VQD are DC-Powered, AC Voltage Monitors used to monitor voltage characteristics of single- or three-phase power lines. This allows normal operation of system loads when the power-line characteristics are within pre-determined limits. These voltage monitors are ideally suited for rugged defense and industrial applications.
-
product
AC Voltage Monitors
NAI's AC- and DC-powered AC voltage monitors are used to monitor and measure voltage characteristics of single- and three-phase power lines. Field-adjustable AC voltage monitors are also available. These monitors are specifically designed for rugged defense and industrial applications.
-
product
Load Cells
Whether you need general purpose, low profile or miniature cells for standard or special applications, you don't have to be an expert in force measurement, because we are. Talk to us about what sort of forces you need to measure, and under what conditions and constraints. We'll walk you through the load cell specification process, quickly and efficiently, and if we don't have what you need on the shelf, we'll be happy to customize an existing product or build a new one from scratch to meet your exacting requirements.
-
product
AC Power Sources
CS Series
AMETEK Programmable Power, Inc.
The CS Series represents an advanced AC current source that addresses increasing demands on manufacturers to test products using real-world current profiles. By combining true current transconductance amplifiers with an advanced digital controller and harmonic power analyzer, CS Series current sources are capable of performing tests that would traditionally have been difficult to accomplish.
-
-
product
Programmable AC Electronic Load
63800
Chroma Systems Solutions, Inc.
The Chroma 63800 Loads can simulate load conditions under high crest factor and varying power factors with real time compensation even when the voltage waveform is distorted. This special feature provides real world simulation capability and prevents overstressing resulting in reliable and unbiased test results.
-
product
AC Current Sensor
RCTi and RCTi 3ph
The RCTi & RCTrms sensors convert ac current to an isolated 0-5V voltage or 4-20mA current loop. TA5V-5A allows compatibility with existing 1A or 5A CT metering circuits. Both offer a choice of proportional (rms) and instantaneous outputs. The available RCT current ranges are 0-100A to 0-50,000Apk. Both RCTi and RCTrms provide accurate measurement over a wide bandwidth ensuring precise measurement even with harmonically distorted wave shapes - using a flexible clip-on sensing coil. The RCTs are available as single and three phase models.
-
product
Programmable AC and DC Power Source
AFX Series
The AFX Series is a family of high power, single, split and three phase, AC, DC and AC+DC output capable Power Sources. Available models range from 6 kVA to 90 kVA with available configurations to 150kVA. Using a modern user interface for ease of use, the AFX Series is cost effective and fully programmable for both basic frequency conversion and advanced AC power line or DC power disturbance test applications.
-
product
AC Digital Clamp Meter
SK-7601
Up to 300A AC., Conductor dia. : Φ27mm max., Compact size clamp neatly fit in your hand., Twist-resistant beaked clamp head., Auto power off., Display hold.
-
product
Load Testing Services
If you're looking for load testing services, you're probably investing heavily in advertising campaigns. But unless you run load tests to ensure your system works properly under real-life load conditions, you can lose both your marketing dollars and potential sales. With UTOR you get the confidence that your application will not damage your business.
-
product
PXI MUX 8 Banks of 16 Channel 1 Pole
40-610-022-8/16/1
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
product
DC Electronic Load
3310G Series（800W）
Has its own control and display panel, CC / CR / CV / CP / Dynamic modes, with 150 sets Store / Recall memory which provides load set-up more efficiently, also can be controlled via RS232、Ethernet、USB and GPIB interface
-
product
Load Switches
Analog Devices load switches provide a highly integrated solution for switching voltage rails on in a controlled manner via an internal, high-side switch. This portfolio features overcurrent and overtemperature protection and supports currents up to 3 A. They provide a very low pass element RDSON to reduce power losses. The combination of the functionality and integration levels of ADI load switches make them extremely well-suited to inrush control applications for pluggable optical modules, line side pluggable interfaces protection, power plane switching, and power rail sequencing applications.
-
product
AC Power Source
61600 Series
Built-in PFC, provide input power factor over 0.98 (full load)AC+DC output mode for voltage DC offset simulationProgrammable voltage,current limitComprehensive measurement capability,V, Hz, Irms, Ipk, Iinrush, P, VAR, VA, PF, CF of current and etc.High output current crest factor, ideal for inrush current testingTurn on, turn off phase angle controlOne-key recall for 9 different voltage and frequencyProgrammable slew rate setting for changing voltage and frequencyAnalog input for power amplifierOptional Analog programming interfaceOptional GPIB and RS-232 interface(Model 61601~61605)Full protection: OP,OC,OV and OT protectionEasy use graphic user interface: softpanel (option)Capable of delivering power output up tp 90KVA by implementing Master-Slave operation
-
product
Axle Load Simulators
In case vehicles need to perform a brake test in laden condition, one could consider to use a load simulator. In that case the vehicles can come to the brake test unladen; the load simulator will add the required load to the axles.
-
product
6000 Series ATE（AC Source）
Voltage output has totally six ranges，maximum up to 500V，convenient for 300V above the voltage regulation test
-
-
product
AC Current Clamp Adapter
LAD-1100
MULTI MEASURING INSTRUMENTS Co., Ltd.
●Selectable measuring range 30mA~30A with CT ratio 10:1 and 30A~3000A with CT ratio 100:1.●φ110mm CT window, possible to measure from leakage to big current up to 3000A.
-
product
Rod End Load Cells
Our rod-end load cells are designed for integration into tension measurement. They are versatile, durable, and fit easily into small spaces such as inline with vehicle tie rods.
-
product
S-Type Load Cells
S-Type load cells are low-cost and high performance side mounted load cells suitable for a number of weighing and general force measurement applications. They come with a 6-foot strain relieved integral cable with pigtail leads that are stripped and tinned for electrical interface.
-
product
Desktop AC Power Supply
DRJ Series
DRJ Series is a stable sine wave output AC power supply of the world's smallest class that integrates the functions of rack-mount multifunctional AC power supply DRA Series in a desktop size. It is a new type of AC power supply that addresses both space saving and high-quality output that are required in experiments, evaluation tests, production line and so forth. With worldwide input feature DRJ can be used anywhere in the world. In addition, it delivers simple operability in a compact size, allowing first timers to operate easily.
-
product
PXI 10 Banks of 8 Channel 2 Pole MUX
40-615-022-10/8/2
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
product
Battery Extra Load Units
Performing capacity/discharge test on a high-capacity battery may be challenging since high requirements are set on the discharge system. In cases when discharge test times need to be reduced, high load capacities are required from the discharge system. The battery extra load unit BXL is an additional load unit designed especially for this purpose.It is primarily used with BLU battery testers. However, the unit is a universal add-on device. This means it can be used as an additional load with any other discharge/capacity tester in the market.When discharge current exceeds the capacity of a single BLU device, extra load unit increases discharge capacity. A system of BLU and BXL instruments enables performing the capacity test in an accurate, user-friendly way in accordance to battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.
-
product
PXI 8 Banks of 8 Chan 1 Pole MUX
40-657-001-8/8/1
40-657 High Density Power Multiplexer Modules are available in a choice of configurations, containing up to 8 separate multiplexers, all 1-pole switching. They are suitable for switching signals to 110VDC/250VAC at 2Amps, 90W.
-
product
AC Filament Switching and Line Relays
*Heavy duty Elkonite contact tips*AC and DC versions available*AC versions available with or without internal rectifier PCB*Automated vision system and operator inspection*Comprehensive automated end of line testing*Test Certificates supplied with each relay*Certificate of Conformity supplied with each order*Recertification and repair services available
-
product
AccuDyne™ AC Dynamometer Systems
SAKOR Technologies offers the AccuDyne™ series of AC motoring dynamometers. These 4-quadrant dynos offer full motoring as well as loading capabilities. AccuDyne dynamometers can be used for testing active components such as engines and electric motors as well as passive components such as transmissions, generators and alternators. AccuDyne dynamometers are available in models from 5 kW through 3 MW. SAKOR Technologies configures each AccuDyne system to meet customer-specific requirements.
